Intelbras XAS 4010 SMART Manuale utente
User manual
XAS 4010 SMART
English
XAS 4010 SMART
Sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The XAS 4010 Smart wireless aperture sensor was developed by Intelbras with 100%
digital technology. The sensor is mounted in SMD components and can be installed
in most products that work at the same frequency and modulation available on the
market.
Operates on FSK or OOK modulation.
Care and safety
» Follow all instructions in the manual for assembling and installing the product.
» LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or perform
any type of processing of personal data from this product.
» This product is intended for indoor and semi-open environments.
» Respect the GAP distance (distance between the sensor and the magnet).
» Conrm that the installation location is stable and appropriate.
» Wireless communication technology, when exposed to environments with high power radia-
tion, may suffer interference and have its performance impaired, for example: locations close
to TV towers, AM/FM radio stations, amateur radio stations, etc.
» Do not expose the XAS 4010 Smart Magnetic Sensor to direct sunlight, rain or moisture.
» For your safety, test the product and systems at least once a week. This is necessary due to
changing environmental conditions, electrical or electronic interruptions, and tampering.Take
all necessary precautions for the safety and security of your property.
Índice
1.Technical specications 5
2.Characteristics 5
3.Product 6
4.Sensor opening 6
5.Registering the XAS 4010 Smart sensor 7
6.XAS 4010 Smart Sensor supervision setup 8
7.Installation 9
8.Battery 11
9.Test 11
10.Homologation 11
Warranty term 12
5
1.Technical specications
Operating voltage Battery 3 V Lithium, model CR2032
Operating current 900 nA
Trigger indication Red LED
RF range 100 meters without hurdles
Transmission frequency 433.92 MHz
Detection Reed Switch SMD
Modulation Supervised (FSK) or unsupervised (OOK)
Baud rate OOK 2 KBps (open source)
Anti jamming Against external interference
Installation environment Internal and Semi-open
Opening gap 8~12mm
Closing gap 6~10 mm
Operating Temperature -10°C to 50°C
Dimensions (W × H × D) Sensor: 37×46×11 mm
Magnet: 11 × 31 × 9mm
Gross weight 0,06 Kg
Net weight 0,04 Kg
2.Characteristics
» Low battery indication;
» Supervised (FSK) or unsupervised (OOK);
» Long-lasting lithium battery;
» SMD reed switch;
» Transmission frequency 433.92 MHz.
6
3.Product
1
2
3
44
57
4
4
6
PAD PAD
FSK
8
1. Sensor cover
2. Light conductor (LED)
3. Sensor base
4. Screw hole for xing
5. Magnet cover
6. Magnet base
7. Battery contact
8. OOK/FSK track
4.Sensor opening
To access the XAS 4010 Smart board to change the battery or change the FSK/OOK
supervision, just remove the cover through the latch, it is not necessary to use tools. This
way the plate will be exposed and ready for handling.
Sensor Imã
Trava
Sensor
Magnet
Lock
7
Remove the board, then insert the battery (model CR2032), respecting the polarity.
CR 2032
3V
PAD PAD
FSK
PAD PAD
FSK
5.Registering the XAS 4010 Smart sensor
To register the XAS 4010 Smart sensor code in the alarm control panel, follow the
procedure below:
Insert the LITHIUM 3 Vdc battery - CR 2032, then type the command to register the
wireless device in the alarm center that will be used (Check the procedure in the
alarm center manual).Then perform a shot moving the magnet away from the sensor,
if the sensor is in a door for example, just open it observing if the LED will light up.
If the LED lights up, it indicates that there was a trip or transmission occurred, if the
LED does not light up, check the battery.
» Low battery sensor: the XAS 4010 Smart has a battery level meter, which me-
asures the voltage and noties you of the best time to change it, if the sensor
ashes the LED quickly in the opening, it indicates low battery level. If the alarm
center is Intelbras, the sensor low battery warning will be indicated on the product
panel. The sensor sends low battery warning in both OOK and FSK modulation.
8
6.XAS 4010 Smart Sensor supervision setup
The XAS 4010 Smart sensor allows you to select between supervised (FSK) and un-
supervised (OOK) modes. To switch between supervision modes, simply remove the
battery from the sensor, open the OOK/FSK jumper indicated on the board (and then
replace the battery), after which the sensor will operate in supervised mode (FSK).
Changing from supervised mode (FSK) to non-supervised mode (OOK) is also simple,
just remove the battery from the sensor, close the OOK/FSK jumper terminals again
and replace the battery, after which the sensor will return to operating mode. unat-
tended mode (OOK). Factory default: unsupervised (OOK)
In FSK modulation, the sensor transmits opening and closing and periodically super-
vises the sensor.
Com Trilha
Não supervisionado
OOK
PAD PAD
FSK
Sem Trilha
Supervisionado
FSK
PAD PAD
FSK
PAD PAD
FSK
PAD PAD
FSK
With track Without
supervision OOK
No supervised
FSK tracking
9
7.Installation
The XAS 4010 Smart sensor can be xed using a double face or cover. If chosen as
an option with a double-sided t, clean the surface that will be in direct contact with
the t and then place on the product base. To use the lid, just open the sensor and
use the holes to pass the lid located on the base of the product, as shown in the
following gure.
Base sensor Base imã
Instalação com parafuso
Base sensor Base imã
Instalação com fita dupla face
Fita
Screw installation
Sensor base Sensor baseMagnet base
Tape
Tornillo
ranurado
simple n.º 2
Magnet base
Installation with double-sided tape
Important: check if the GAP distance (distance between the sensor and the image)
is within the specication, to avoid unwanted triggering in the event of any vibration
in the structure in which the sensor is installed.
Note: the type of surface where the sensor is installed may inuence the distance
from the GAP.
» GAP opening: 8 ~ 12 mm
» GAP closure: 6 ~ 10 mm
GAP
10
To close the sensor, check the pin located on the base, it must be positioned on the
same side as the battery, after positioning the base, just press it for locking, there is only
one way to close the sensor, check image 01 To close the magnet, just position the base
and press it, image 02.
Pino
Aperte
para
travar
Aperte
para
travar
Figura 01 Figura 02
Pin
Press to
lock
Press to
lock
Figure 01 Figure 02
The sensor must be installed according to the images below, with the magnet aligned
with the sensor body and with the smallest possible distance between them, so that
the magnet is in contact with the magnetic eld sensor.
Note: for closing and opening the SMD magnetic eld sensor, the distances from the
GAP must be respected.
Altri manuali per XAS 4010 SMART
1
Indice
Altri manuali Intelbras Hardware di rete
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
