IntelliCorder 1500 Manuale utente

IntelliCorder 0Camera System

ModelNo.1500

Operation Instructions

IntelliCorder 0Camera System

User’s Guide

Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future reference.

Congratulations

With the IntelliCorder 0, you can monitor the entrance of any home or business and safely answer

your door before opening. The internal Digital Video Recorder (DVR) can capture the video/audio of

any visitor even when you are not present. The IntelliCorder 0is a high-quality, battery-operated

monitoring device. It uses a passive infrared (PIR) motion sensor to detect guests/intruders at your

front or back door and projects an on-screen image onto the internal monitor screen. Once powered

on, it will activate a video recording, storing it in the internal memory or onto a SD memory card.

This instruction manual explains in simple steps how to install, use and care for your new

IntelliCorder 0in your home, office or business.

Parts Checklist

Identify all parts before proceeding with installation

1pc. Color Monitor

1pc. Front Sensor with double-side tape

1pc. Mounting Bracket with double-sided tape

2 pcs Support tubes (2 sizes)

3pcs x AAA Alkaline Batteries (not included)

1pc. Clock Battery (installed in Camcorder)

1pc. Screw for Bracket

1pc. Tool

Things You Should Know

FCC Warning

Any unauthorized changes or modifications to the equipment would void the users authority to

operate. This IntelliCorder 0complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

1. The IntelliCorder 0may not cause harmful interference.

2. The IntelliCorder 0may accept any interference received.

Important Safeguards

1. Cleaning – Turn off this video unit before cleaning. Do not use strong or abrasive detergents. Use

a dry cloth to clean the camera body when dirty. In case the dirt is hard to remove, use a damp

(not wet) cloth for cleaning.

2. Water and Moisture – Do not use any component of this system in an exposed outdoor area,

except the outer part of front sensor. Do not operate this system in the presence of explosive or

flammable fumes.

Precautions

1. Do not attempt to disassemble the camera. There are no user-serviceable parts inside

2. Handle the IntelliCorder 0with care – Avoid striking or shaking. Improper use or storage could

damage the IntelliCorder 0. Modifying or tampering with the device or its internal components can

cause a malfunction and void the IntelliCorder 0’s warranty. If you feel the IntelliCorder 0may not

be performing correctly, contact customer service for assistance.

3. Motion Detection – The PIR motion sensor will NOT detect motion through glass storm doors,

screen doors or metal gates.

4. Camera faceplate care – Do not clean the lens with strong or abrasive detergents. Use lens tissue

or a cotton tipped applicator and ethanol alcohol.

5. Light Source – The Camera viewing area must be illuminated with a suitable light source during

evening and nighttime hours.

6. Door Mounting – The product should be mounted to a door, only as recommended by the

instructions. Contact customer service for any questions.

7. Stand-by MODE – When not using your IntelliCorder 0, press and hold power button to go to

stand-by mode.

8. Do not touch the LCD screen with a sharp-pointed object.

9. If your IntelliCorder 0 is used in a cold environment, a residual image may appear on the LCD

screen. This is not a malfunction.

Features

Monitor and Sensor Front

1. LCD Screen – 1.5” LTPS LCD

2. Speaker – play back the audio sound of recorded file in PLAY mode

3. SD Card Insert Slot

4. Battery Cover

5. Microphone

6. Motion-activated Sensor – detects motion up to 6.5 feet (2 meters) away from a horizontal angle

of up to 125 degrees (Motion cannot be detected through glass storm doors, screen doors or

metal gates).

7. Lens

Motion and Sensor Back

1. Terminal

2. Clock Battery Cover

Control Panel

1. OK – confirm setting

2. CURSOR – 

3. MENU / power – enter Menu screen; hold to turn device off or on at LIVE mode

4. PLAY – enter or exit PLAY mode

5. RESET – use a pointer or alike to press this button to reset the unit

Operation Indicators

1. New Message Light Indicator (Green)

2. Low Battery Light Indicator (Red)

Preparation

Install Battery

1. Slide downward and pull open the battery cover

2. Install 3 x new alkaline or rechargeable AAA Batteries (not included) into the battery compartment,

observing proper +/- polarities as indicated.

3. Once the batteries are installed, replace the cover and slide up to lock the battery cover.

To Remove Battery

1. Slide downward and pull open the battery cover

2. Take out batteries from the compartment

Battery Care

Caution:

* Do not use old or insufficiently charged batteries

* Do not place batteries near or dispose of in fire

* Never attempt to disassemble or reassemble Batteries

To avoid Battery damage

* Do not drop or jar Batteries

* While not in use, remove Batteries from the IntelliCorder 0, and store in a cool, dark, dry place.

CLOCK Battery Installation

The IntelliCorder 0’s internal clock operates on a CR2032 lithium flat cell battery (included). To

replace battery when expired:

1. Remove the cover on the back of the unit by rotating tabs into unlock position.

2. Install a new CR2032 battery into the clock battery compartment, observing proper +/- polarities

as indicated.

3. Replace the battery cover. Rotate tabs into lock position.

Warning:

* Dispose of old battery promptly and properly. Do not burn or bury.

* Replace battery with CR2032 only. Use of another battery may present a risk of damage to the

IntelliCorder 0.

* Keep away from children. Do not recharge, disassemble or dispose of in fire.

Note:

* Keep battery out of children’s reach. Swallowing it may be harmful.

* Battery life is approximately two years.

Installation

Choose a Mounting Location

The IntelliCorder 0is designed to mount on a smooth, flat door surface from 30mm to 65mm. Select

a door/entrance you wish to monitor. The recommended mounting height is approximately 5-6 feet.

At this height, the PIR sensor detects motion up to 6.5 feet (2 meters) away, with a viewing angle up

to 80 degrees.

To help avoid false activation, mount your camera:

* Away from direct sunlight

* Away from heat sources, such as space heaters, radiators, and exposed light bulbs

* Away from strong drafts, like those caused by central heating vents

1. Prepare the mounting space by first removing the original door peephole hole viewer. If there is

no peephole, then you will need to drill a hole of an at least ½” (12.5mm) diameter at desired

location.

2. Clean the surface where the PIR camera sensor is to be mounted.

3. Carefully pull out the ribbon cable from the camera tube.

4. Remove the backing of the double-sided adhesive tape on the back of the PIR. Carefully feed the

ribbon cable and tube through the peephole to the other side of the door. Be careful not to stick

the camera to the door. Once you have the camera aligned properly, press the camera to the door

allowing the adhesive tape to the camera in place. As illustrated below, keep the PIR sensor on

the top.

5. Remove the backing of the double-sided adhesive tape on the back of the mounting bracket.

Carefully feed the ribbon cable through the mounting hole of the mounting bracket. Once you

have the mounting bracket aligned properly, press it to the door allowing the adhesive tape to the

mounting bracket in place.

6. Feed the ribbon cable through the support tube. Place the Support tube through the Mounting

Bracket into the peephole and screw onto the PIR tube. Use the Adjustment Tool to turn the

Support tube clockwise until the mounting plate is secured to the door. Take care not to over-

tighten the Support Tube.

7. Connect the ribbon cable plug to the INPUT Connector by matching the arrow symbols on the

plug and the terminal.

Caution

Do not rotate the camera or recorder without disconnecting the ribbon cable first. Damage

to the ribbon cable will occur and void the warranty.

8. Hook the Monitor onto the Mounting Bracket. Thread a screw to hole of the unit’s battery

compartment and turn it clockwise.

9. To activate clock battery, pull the insulator tab from the backside of Monitor.

10.Position the slot located at the top edge of the IntelliCorder 0onto the top tab of the Mounting

Bracket. Next, fit the slot located at the bottom edge of the IntelliCorder 0onto the lower tab of the

mounting bracket. Press the IntelliCorder 0firmly into position.

11.If using an SD memory card (not supplied) insert into the slot at the top of Monitor.

12.Insert the Batteries into the compartment, as indicated by polarity symbols (+ and -) marked inside.

See Battery Installation (Page 5).

Operation

For First Use, the camera will undergo self-calibration within several seconds. IntelliCorder 0has

different languages, time/date format and flicker options available. Select your desired setting first

before use (see page 12).

To save battery power, the IntelliCorder 0will enter into sleep mode at 5 seconds when not in use or

no motion is detected.

SD Card (not included)

For increased recording time, data (Video files) can be stored onto standard SD memory cards. Data

from the IntelliCorder 0’s internal memory can also be downloaded to an SD card. The IntelliCorder 0

accepts SD memory cards up to 4GB.

SD Card Insertion/Removal

1. Insert SD card with the logo facing outward toward the LCD screen. Press the SD memory card

inward until it clicks into position.

2. To remove the SD memory card, press on it to release. It will click and eject out.

Record / Playback Time

Use one of the following SD card sizes in the chart below. The resolution setting determines the

recording length.

Resolution 128MB 512MB 1GB 4GB

Fine 8 min 32 min 64 min 256 min

SP (Standard Play) 13 min 52 min 104 min 416 min

LP (Long Play)* 21 min 84 min 168 min 672 min

* LP playback may contain more picture noise

Motion-Activated RECORD

The IntelliCorder 0can record high-resolution video with sound of visitors/intruders at your front or

back door, even when you are not home.

Before you begin

* Check the Battery Indicator

* If using an SD memory card, ensure it is properly installed.

1. When motion is detected, the IntelliCorder 0begins recording shortly after the PIR detects motion.

It continues recording until motion has ceased for 5 seconds.

2. The IntelliCorder 0is equipped with internal memory for immediate recording storage. Video files

are stored as MOTION JPEG format. If no SD memory card is detected, files will be stored to

internal memory. For longer recording time, you can use SD memory card up to 4GB. When the

memory is full (either internal or on SD memory card), IntelliCorder 0’s auto-deletion function will

erase three oldest files each time.

PIR Sensor activation may not occur when:

* Motion is very slow or very fast.

* Moving object is very small.

* Motion occurs only in 1 corner of viewing area.

Note: The PIR sensor will not detect motion through a glass storm door, screen door or metal gate.

Record Status

Red – Movie recording

Green – live preview

Set Clock

The clock time is lost in last power off

FINE

Video Quality

320x240 @ 30fps

320x240 @ 20fps

320x240 @ 13fps

Battery Status

Full Power Level

66% Power Level

33% Power Level

Empty

1:20 Record Elapsed Time /

Remain Time SD/MMC card Status

Present and Valid

Present but Locked (Red in color)

01/01/2005

12:00 AM Clock Info / Stamp Mode

Manual RECORD

1. When no motion is detected but you desire to look outdoor environment, press POWER to wake

up camera and LCD screen at LIVE mode.

2. Press OK to manually start recording. Press OK again to stop recording.

PLAY Back Video Files using Monitor

A flashing Green light indicates new files have been recorded. You can monitor the playback picture

on the LCD screen using the IntelliCorder 0’s DVR features.

Press POWER to wake up camera and LCD screen at Live mode

1. Press PLAY and Thumbnail file(s) will appear on the screen.

2. Use ⊳ to select the desired file to preview.

3. Press OK to open it.

4. Uses OK to play/pause/replay the video.

After 30 seconds the IntelliCorder 0will go into sleep mode.

When the video is playing,

* Press ⊳ to skip to previous/next video.

* Press to increase volume or to decrease it.

When the video is paused/stopped,

* Press ⊳ to skip to previous/next video.

* Press  to go back to thumbnail screen.

Indice

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente