Intelligent Automation ARGUS Manuale utente

Protected under U.S. patent number 8,232,878

Revision G October 2016

Page | 1

Table of Contents

1 FCC Certifications and Regulatory information .................................................................................... 2

2 Quick Start Guide .................................................................................................................................. 3

3 Hardware Overview .............................................................................................................................. 7

3.1 Sensor Node Description ..............................................................................................................7

4 Software Overview.............................................................................................................................. 10

4.1 Initial Setup Wizard.....................................................................................................................10

4.2 User Interface Overview .............................................................................................................11

4.2.1 Main Toolbar....................................................................................................................... 11

4.2.2 GUI Panels...........................................................................................................................11

4.3 Configuration Wizard..................................................................................................................13

4.4 Configuration and Active Modes ................................................................................................14

4.5 Node Positioning......................................................................................................................... 14

4.5.1 Drag-and-Drop Node Positioning........................................................................................15

4.5.2 Manual Lat/Long Node Positioning..................................................................................... 15

4.5.3 GPS Node Positioning..........................................................................................................15

4.6 Link Configuration.......................................................................................................................16

4.6.1 Link Configuration Window ................................................................................................16

4.6.2 Link Configuration Toolbar.................................................................................................. 17

4.7 Link Metrics Mode ...................................................................................................................... 19

4.7.1 Link Metrics Guidelines.......................................................................................................20

4.8 Alerts........................................................................................................................................... 20

4.8.1 Alert Log Files......................................................................................................................21

4.9 Plug-in Configuration ..................................................................................................................21

4.9.1 Camera Plug-in....................................................................................................................21

4.9.2 Text Message Plug-in ..........................................................................................................23

5 System Shutdown ...............................................................................................................................25

6 Node Deployment Guide ....................................................................................................................26

7 Troubleshooting..................................................................................................................................28

Page | 2

1FCC Certifications and Regulatory information

FCC Part 15 Class B

Radio Frequency Interface (RFI) (FCC 15.105)

This device has been tested and found to comply with the limits for Class B digital devices pursuant to

Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference in a residential environment. This equipment generates, uses, and can radiate

radio frequency energy, and if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Labeling Requirements (FCC 15.19)

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Modifications (FCC 15.21)

Changes or modifications to this equipment not expressly approved by Intelligent Automation, Inc. may

void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm

or more should be maintained between the antenna of this device and persons during device operation.

To ensure compliance, operations at closer than this distance are not recommended.

Page | 3

2Quick Start Guide

This Quick Start section of the user manual presents the basics of getting an ARGUS deployment up and

running. For more details on each topic, refer to the later sections in this manual.

Step 1: Turn on the laptop PC

Note that if the laptop is locked, the default username is ‘argus’ and the password is ‘iai’

Step 2: Connect the Gateway node and turn it on

The ‘Gateway Node’ enables communication between the ARGUS nodes and the laptop PC. The

Gateway node connects to the PC via a short USB cable, and uses a 2.4GHz antenna with a standard RP-

TNC connector) to communicate with the ARGUS network.

-Attach an antenna to the port on the top of the Gateway node.

-Connect the included USB cable to the rugged connector on Gateway Node and plug the other

end into one of the USB ports on the right side of the laptop (see Figure 1). Be sure to use the

same USB port each time you connect the Gateway Node, as the software is configured to look

for it on the same port each time. The gateway will power on as soon as it is connected to the

USB port.

-Attach the external 2.4GHz antenna to the Gateway Node. Optional: Connect an RF extension

cable and outdoor rated antenna to position the antenna outside of a building or on a rooftop.

For antenna coax cable runs greater than 10ft, use an RF amplifier (contact IAI for details).

Figure 1: ARGUS Gateway connection to PC

Step 3: Start the ARGUS software

To start the ARGUS software, click the ‘ARGUS’ software icon on the desktop (see Figure 2). The splash

screen for the ARGUS View application should appear, then after a few seconds, the main graphical user

Page | 4

interface (GUI) should appear. For a full description of the GUI, modes, buttons, etc. see Section Error! R

eference source not found..

Figure 2: Starting the ARGUS software. Click the 'ARGUS' icon (left) to start the GUI software (right)

Step 4: Create a new ARGUS configuration

Prior to operating the ARGUS system, it must be configured by defining the node locations and active

fence links to monitor.

-Press the ‘Configure’ button in the upper left corner of the screen.

-Select ‘New’ as the Configuration Type and click ‘Next’.

-Specify a configuration description (optional) and select a Map Type: None, Satellite, or User

Defined (see Section 4.3 for descriptions). Click ‘Next’.

-Click ‘Next’ to leave Camera Monitoring disabled (see Section 4.9.1 for details).

-Click ‘Finish’ to leave SMS/MMS Notifications disabled (see Section 4.9.2 for details).

-The new configuration has been created, and you are now in Configuration Mode. The main GUI

should again be displayed (see Figure 3).

Page | 5

Figure 3: Initial Configuration Mode view (with satellite map type selected)

Step 5: Turn on fence nodes

Attach antennas to and turn on at least two ARGUS fence nodes. They will automatically register with

the system and appear in the ‘Node Manager’ list on the left side of the screen. The nodes will appear

on the screen with the identification number corresponding to the node ID number on the back of each

ARGUS unit. See Section 4.2.2 for detailed descriptions of the icons that are shown in the Node

Manager.

Figure 4: Configuration Mode with two ARGUS nodes turned on

Page | 6

Step 6: Position nodes on the on-screen map

Pan and zoom to the desired area of the on-screen map. Drag the nodes from the Node Manager list

directly onto the map or click-and-drag the nodes around on the map as desired. See Section 4.5 for full

details regarding placement on nodes on the map.

Step 7: Enable fence links

Click on a link to display the link details window, in which you may specify a link description (optional)

and set the link as either ‘Active’ (actively monitored by the software) or ‘Inactive’ (ignored by the

monitoring software). Active links are indicated in the Map View by solid yellow lines and Inactive links

are indicated by dotted blue lines. See Figure 5 for an example configuration with three nodes, one

active link, and two inactive links. See Section 4.6 for full details regarding link configuration.

Figure 5: Map view of three node configuration with one Active link (yellow line) and two Inactive links (blue dotted lines)

Step 8: ‘Commit’ the configuration

Press the ‘Commit’ button in the lower left corner of the Map View to save the ARGUS configuration and

place the system into Active Mode. The system will now be continuously monitoring and logging any

fence link triggers, displaying alerts both within the Map View and in the Alerts panel on the right side of

the GUI. See sample screenshot in Figure 6, and refer to Section 4.8 for more details regarding the

alerts.

Page | 7

Figure 6: ARGUS GUI in Active Mode. Alerts are shown in the right panel; Alert History is shown in the bottom panel, and

current status is shown in the center Map View.

3Hardware Overview

3.1 Sensor Node Description

Each ARGUS sensor node is physically contained within a rigid fiberglass tube with a robust plastic base.

The sensor itself is contained within an electronics module that sits inside the top of the fiberglass tube

body. The base can free stand on flat ground, it can be anchored into the ground using 3/8” spikes, or it

can be weighted down using a traffic cone weight or other suitable weight.

Page | 8

Figure 7: ARGUS Node (left). Close-up of electronics module removal (right).

The top portion of the ARGUS sensor node includes the Electronics Module (see Figure 7 and Figure 8).

The Electronics Module is removed from the pole via a simple twist-lock mechanism. The Electronics

Module is comprised of the ARGUS sensor PCB (housed within the module) and a single D-cell Lithium

battery. Then the battery is installed, the ARGUS sensor PCB will automatically start up and attempt to

join the sensor network. The LED indicator will blink green three times to indicate that the ARGUS

sensor node has powered on. If this indication is not seen, check the battery state and battery

connections.

Figure 8: ARGUS Node electronics module (left) and battery replacement (right).

Page | 9

The typical runtime for a single fully charged Lithium D-cell battery is approximately 5 months, although

this may vary slightly due to temperature and the specific network configuration of the sensor node. The

ARGUS node has been tested with the OmniCel ER34615 Lithium D-cell battery, which has a nominal

capacity of 19Ah at 3.6V. Other similar Lithium primary cell batteries should also work well.

Indice

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente