Intelligent Weighing Technology AGS-6000BL Manuale utente

A Higher Level of Precision…A Higher Level of

Performance

AGS SERIES

ELECTRONIC WEIGHING SCALE

OPERATION MANUAL

PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE

ATTEMPT TO OPERATE THE SCALE

JUNE 2016 REV 1

This document hosted by: www.oldwillknottscales.com

Specifications subject to change without prior notice

CONTENTS

CAUTIONS

1. INSTALLATION

2. SPECIFICATIONS

3. KEYBOARD LAYOUT AND DESCRIPTION

4. INITIAL SETUP

5. INSTRUCTION FOR USE

6. TROUBLE SHOOTING

7. DAILY CARE AND MAINTENANCE

CAUTIONS

1. This unit is legal for trade only when it is sealed

(and/or stamped) and bearing a serial number. Do not

attempt to break the seal (or stamp) affixed to this

scale or remove the serial number. Contact your dealer

for more information and after sales service. (Not

available in USA)

2. For most accurate weighing result, do not use this

scale in where or when the environment condition falls

beyond as those listed on SPECIFICATIONS.

3. Do not attempt to open this unit or conduct any trouble

shootings other than those listed on TROUBLE

SHOOTING.

4. Do not use this scale for chemical substances or in

any environment that contains chemical vapor.

5. Precision measuring instrument, handle with care.

6. Do not open scale. No user serviceable parts inside.

1. INSTALLATION

1.1 Check and make sure that the following accessories

are included:

Operation Manual x 1

Scale x 1

Stainless steel platter x 1

Power adaptor x 1

Dust Cover x 1

Contact your dealer if any item is missing.

1.2 Place the stainless steel platter on the scale.

1.3 Power on the scale

a. Before charging the scale or power on with the

adaptor supplied. Please make sure the input

voltage listed on the back of the adaptor matches

with the local voltage. If not, do not use it

and contact your dealer immediately.

b. Before first time use, charge the scale for at

least 8 hours to ensure the best performance.

2. SPECIFICATIONS

Model No.

Capacity

(Max)

Division (e)

OIML

Non-OIML

Extended

AGS-1500

1500g

0.5g

0.2g

0.05g

AGS-3000

3000g

0.5g

0.1g

AGS-6000

6000g

0.2g

AGS-15K

15kg

0.005kg

0.002kg

0.0005kg

AGS-30K

30kg

0.01kg

0.005kg

0.001kg

Tare Range

Full Tare Range

Power-on

Zero Range

±10% Max

Zero Range

±2% Max

Min. Load

20e*

Power Source

By Built-in Rechargeable Battery or AD/DC

Power Adaptor

Operating

Environment

0o~40oC (32o~104oF),

Non-condensed. R.H.≦85%

Specifications subject to change without notice

NOTE 1:

OIML = Legal for trade (1/3000)

Non-OIML = Not legal for trade (1/6000~1/7500)

NOTE 2:

Extended Display Function does not support avoirdupois

weight units (lb/lb and lb/oz)

3. KEYBOARD LAYOUT AND DESCRIPTION

1. OFF KEY

Press this key to turn scale off

2. ON/ZERO KEY

Press this key to turn scale on or set weight to zero

3. MODE KEY

Press this key to shift among different weight units

and/or turn backlight on/off

4. TARE KEY

Press this key to tare off the weight of a container.

5. FUNCTION KEY

Press this key to enter counting function or percentage

function

6. SAMPLE KEY

Press this key to sample the weight place on the platter

and engage the counting function or percentage function

7. MODE INDICATOR

This indicator shows current weight unit or operating

mode engaged

8. ZERO INDICATOR

This indicator appears to indicate a zero weight status

9. NET INDICATOR

This indicator appears to indicate the tare function

is in operation and weight displayed is net weight

10. LO-BAT INDICATOR

When this indicator appears, recharge the scale

immediately. Failure to do so may cause unrecoverable

damage to the rechargeable battery inside scale

4. INITIAL SETUP

4.1 PLACING THE SCALE

In order to obtain an accurate weighing result, the scale

must be placed on a strong and level surface.

If required, adjust the adjustable feet underneath scale

to obtain a level position. Refer to the bubble indicator

for leveling condition.

4.2 INTERNAL SETTING

4.2.1 Display Segment Check

User can enter this function to check to see if the display

and backlight (if purchased) are functioning properly.

a. Scale is off

b. Press and hold TARE, then press ON/ZERO

c. Scale displays F.1

d. Press TARE once

e. Scale displays F.2

f. Press MODE and all segments will light up to allow

user to check the condition of display

g. Press TARE for next function setup or ON/ZERO to

restart the scale

4.2.2 Select Auto Power Off Setting

The scale is equipped with Auto Power Off Function. The

scale will power off automatically if it is not used

for 4 minutes. Follow the below steps to enable/disable

Auto Power Off Function.

a. Scale is off

b. Press and hold TARE, then press ON/ZERO

c. Scale displays F.1

d. Press TARE three times

e. Scale displays F.4

f. Press MODE to shift between 0._OFF and 4._OFF

-To enable Auto Power Off Function, press TARE when

4._OFF appears

-To disable Auto Power Off Function, press TARE when

0._OFF appears

g. Press ON/ZERO to restart the scale or TARE for next

function setup

4.2.3 Select Auto Tare Function

This scale is equipped with auto tare function which

tares off the initial weight automatically when this

function is engaged. The tare weight is automatically

cleared when everything is removed from platter.

a. Scale is off

b. Press and hold TARE, then press ON/ZERO

c. Scale displays F.1

d. Press TARE six times

e. Scale displays F.9

f. Press MODE to select between “Tr_on” or “TroFF”

-To enable Auto Tare Function, press TARE when Tr_on

appears

-To disable Auto Tare Function, press TARE when TroFF

appears

g. Press ON/ZERO to confirm and restart the scale or

TARE for next function setup

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Intelligent Weighing Technology Scala