Intellihot I200 Scheda tecnica

To avoid product damage, personal injury, or

even possible death, carefully read, understand,

and follow all the instructions in the Installation

and Operation manuals before installing this

product. Improper installation, adjustment, alteration, or

maintenance can cause injury, loss of life, and/or property

damage. This water heater should be installed and

serviced by a qualified technician. The lack of proper

service can result in a dangerous condition.

This manual contains safety information, installation

instructions, and maintenance procedures. It must be left

with the homeowner or placed near the water heater in

a noncombustible place. The customer should retain this

manual for future reference.

WARNING

If the information in these instructions is not followed

exactly, a fire or explosion could result causing

property damage, personal injury, or death.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by

a qualified installer, service agency, or the gas

supplier.

FACTORY PRESET FOR USE WITH

NATURAL GAS

Direct-Vent Automatic Instantaneous Water Heater

(Chauffe-eau automatique instantané à ventilation directe)

FOR INDOOR INSTALLATIONONLY

(POUR INSTALLATION À L'INTÉRIEUR SEULEMENT)

120 Volt, 60 Hz, 5 Amps

Type of Gas

(Type de gaz)

: . . . . . . . . . . . . . . . .

Input Rating

(Entrer le Classement)

: Btu/hr Maximum . . .

Btu/hr Minimum . . .

Maximum Inlet Gas Pressure: . . . . . . . . . . . .

Minimum Inlet Gas Pressure: . . . . . . . . . . . .

Minimum Inlet Gas Pressure (for adjustments): . .

Maximum Water Pressure: . . . . . . . . . . . . .

Minimum Water Pressure: . . . . . . . . . . . . .

Recovery Rating: . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . .

Thermal Efﬁ

ciency / :

Energy Factor:

NOx Emissions:

. . . . . . . .

(Pursuant to South CoastAir Quality Management District Rule 1146.2)

(Moins de 20 ppm)

(Jusqu'à 98 % / 0.94) (Jusqu'à 98 % / 0.94)

(Moins de 20 ppm)

(Dégagements minimums)

(Des non-combustibles) (D'une construction

combustible)

(conformément au règlement 1146.2 du "South Coast Air Quality Management District)

Top of heater

Minimum Clearances

From

Non-Combustibles

From Combustible

Construction

(Dessus du chauffe-eau)

Back of heater

(Arrière du chauffe-eau)

Front of heater

(Avantdu chauffe-eau)

Bottom of cabinet

(Côté canalisation)

Side (Côté)

5/8 in (15.8 mm)

6 in (15.2 cm)

2 in (50.8 mm)

12 in (30.4 cm)

5/8 in (15.8 mm)

6 in (15.2 cm)

2 in (50.8 mm)

1/2 in (12.7 mm)

12 in (30.4 cm)

Intellihot Green Technologies Inc.

2900 W. Main St.

Galesburg, IL 61401

Phone: (877) 835- 1705

Email: [email protected]

Web: www.intellihot.com

Factory Preset

Natural Gas

(Réglage en usine pour gaz naturel)

199,000

20,000

13.0 W.C. (3.20 kPa)

8.0 W.C. (2.00 kPa)

150 psi (1034 kPa)

15 psi (103 kPa)

265 GPH (1003 LPH)

Up to 98% / 0.94

Less than 20 ppm

Field Conversion* to

Propane Gas

(Conversion* sur place au gaz propane)

199,000

20,000

10.5 W.C. (2.62 kPa)

3.0 W.C. (0.76 kPa)

11.0 W. C. (2.74 kPa)

150 psi (1034 kPa)

15 psi (103 kPa)

265 GPH (1003 LPH)

Up to 98% / 0.94

Less than 20 ppm

Check Box if

Converted to

Propane Gas

*Refer to Installation and Operation

manual for conversion procedure.

(Se référer au manuel d'installation et

de fonctionnement pour la procédure de

conversion.)

PRÉRÉGLAGES D'USINE POUR UTILISATION AVEC

GAZ NATUREL

(Pression de gaz d'arrivée maximum)

(Pression d'eau maximum)

(Pression d'eau minimum)

(Caractéristique de recouvrement)

(Efficacité thermique / Facteur énergétique)

(Émissions de NOx)

(Pression de gaz d'arrivée minimum)

(Pression de gaz d'arrivée minimum (pour ajustements))

Cocher la case si converti au gaz propane

ETL STICKER

Serial Number:

IGT-LBL-0005-01

(Numéro de série)

(Collant ETL)

Operation and

Installation

Manual

Model: i200, i250

i200P, i250P

This product complies with ANSIZ21.10.3 (2011) / CSA

4.3 Gas Water Heater. For use as potable water heating.

The Energy Star rating applies only to the i200 and

i200P models.

Smart. Ecient. Endless

— Ne pas entreposer ni utiliser d’essence ou

ni d’autres vapeurs ou liquides inflammables

à proximité de cet appareil ou de tout autre

appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ

•

Ne pas tenter d’allumer d’appareil.

•

Ne touchez à aucun interrupteur; ne pas vous

servir des téléphones se trouvant dans

le bâtiment.

•

Appelez immédiatement votre fournisseur de gaz

depuis un voisin. Suivez les instructions

du fournisseur.

•

Si vous ne pouvez rejoindre le fournisseur,

appelez le service des incendies.

— L’installation et l’entretien doivent être assurés

par un installateur ou un service d’entretien

qualifié ou par le fournisseur de gaz.

AVERTISSEMENT

Assurez-vous de bien suivre les instructions données

dans cette notice pour réduire au minimum le

risque d’incendie ou d’explosion ou pour éviter tout

dommage matériel, toute blessure ou la mort.

Certified to

NSF/ANSI 372

3 i200, i250, i200P, i250P Installation and Operation

Table of Contents

1. General Information

1.1 Items Shipped With Water Heater . . . . . . . . . . . . . . . 4

1.2 Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Serial Number Plate Locations . . . . . . . . . . . . . . . . . . 4

2. Safety

2.1 Safety Signal Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Installation Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Technical Data

3.1 Specications Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 High Elevation Installations. . . . . . . . . . . . . . . . . . . . . 7

3.3 Dimensional Specications . . . . . . . . . . . . . . . . . . . . . 8

3.4 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4. Preparation Before Installation

4.1 Selecting an Installation Site. . . . . . . . . . . . . . . . . . . 10

5. Wall Mounting

5.1 Clearance Requirements. . . . . . . . . . . . . . . . . . . . . . . 11

5.2 Mounting the Unit to the Wall . . . . . . . . . . . . . . . . . 11

6. Gas Connections

6.1 Installation Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . 12

6.2 Excess Flow Valve (EFV). . . . . . . . . . . . . . . . . . . . . . . . 12

6.3 Gas Pipe Sizing Tables . . . . . . . . . . . . . . . . . . . . . . . . . 13

6.4 Gas Pressure Regulator . . . . . . . . . . . . . . . . . . . . . . . . 14

6.5 Venting of Gas Supply Regulators. . . . . . . . . . . . . . 14

7. Venting and Materials

7.1 Venting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

7.2 Exhaust Vent Materials . . . . . . . . . . . . . . . . . . . . . . . . 15

7.3 Air Intake Vent Materials. . . . . . . . . . . . . . . . . . . . . . . 15

7.4 Venting Congurations. . . . . . . . . . . . . . . . . . . . . . . . 16

7.5 Two Pipe Vent System (Direct Vent) . . . . . . . . . . . . 16

7.6 Venting Termination. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7.7 Venting Clearance Specications . . . . . . . . . . . . . . 21

7.8 Common Venting for Multiple Units. . . . . . . . . . . . 22

8. Water Connections

8.1 Water Line Connection Guidelines . . . . . . . . . . . . . 26

8.2 Water Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.3 Hot Water Side Connection . . . . . . . . . . . . . . . . . . . . 26

8.4 Cold Water Side Connection . . . . . . . . . . . . . . . . . . . 27

8.5 Condensate Line Installation. . . . . . . . . . . . . . . . . . . 27

8.6 External Recirculation Options. . . . . . . . . . . . . . . . . 28

9. Electrical

9.1 Electrical Code Requirements. . . . . . . . . . . . . . . . . . 30

9.2 Electrical Connection and Polarity . . . . . . . . . . . . . 30

10. Propane (LPG) Conversion

10.1 General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . 31

10.2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

11. Adjusting CO2Level

11.1 General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . 32

11.2 Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

12. Operation

12.1 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

12.2 Display Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

12.3 Turning Water Heater ON and OFF . . . . . . . . . . . . . 35

12.4 Resetting (Clear) Error Codes . . . . . . . . . . . . . . . . . . 35

12.5 Setting the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

12.6 Adjusting the Water Temperature . . . . . . . . . . . . . . 36

12.7 Real Time Temperature and Flow of the System 36

12.8 Flue and Domestic Water Temperature . . . . . . . . . 36

12.9 Error Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

13. Programming

13.1 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

13.2 Viewing and Setting Modes of Operation . . . . . . 38

14. Maintenance

14.1 Cleaning the Inlet Water Strainer. . . . . . . . . . . . . . . 44

14.2 Draining the Water Heater . . . . . . . . . . . . . . . . . . . . . 44

14.3 Filling the Water Heater . . . . . . . . . . . . . . . . . . . . . . . 45

15. Troubleshooting

15.1 Error Code Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

15.2 Wiring Diagram Chart . . . . . . . . . . . . . . . . . . . . . . . . . 48

15.3 Operational Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 49

16. Serviceable Parts

16.1 Electrical Components (All Models) . . . . . . . . . . . . 50

16.2 i200 and i250 Water Lines and Fittings . . . . . . . . . 51

16.3 i200P and i250P Water Lines and Fittings. . . . . . . 52

16.4 Blower, Gas Valve, and Exhaust (All Models) . . . . 53

16.5 Ignition Components (All Models) . . . . . . . . . . . . . 54

17. Requirements for State of Massachusetts . . .55

18. Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

19. Product Warranty Card. . . . . . . . . . . . . . . . . . . . .59

i200, i250, i200P, i250P General Information 4

1. General Information

1.1 Items Shipped With Water Heater

The following items are shipped with the water heater; upper

mounting bracket (1), condensate drain (2), communication

cable (3), Operation and Installation manual (4).

Note: Items 5 through 7 are spare parts shipped with the

unit. Two buss fuses, 10 Amp (5), electrode seal (6),

and O-rings (7).

IQ-103

To avoid productdamage,personal injury,or

evenpossibledeath,carefullyread,understand,

andfollowalltheinstructionsin theInstallation

andOperationmanuals before installingthis

product.Improperinstallation,adjustment,alteration,or

maintenance cancauseinjury,lossoflife,and/orproperty

damage. This water heater shouldbeinstalledand

servicedbyaqualied technician.Thelackofproper

servicecanresult in adangerouscondition.

Thismanualcontainssafetyinformation,installation

instructions, andmaintenanceprocedures.Itmustbeleft

withthehomeowneror placednear thewaterheaterin

a noncombustibleplace.Thecustomer shouldretainthis

manual forfuture reference.

WARNING

Ifthe informationintheseinstructionsisnot followed

exactly,afireorexplosioncouldresultcausing

propertydamage,personalinjury,ordeath.

—Donotstoreorusegasolineor otherflammable

vaporsandliquidsinthevicinity ofthisorany

otherappliance.

WHATTODOIFYOUSMELLGAS

•

Donottrytolight anyappliance.

•

Donottouchanyelectricalswitch;donot use

anyphoneinyourbuilding.

•

Immediatelycallyour gassupplierfroma

neighbor’sphone. Follow the gassupplier’s

instructions.

•

Ifyoucannotreachyourgassupplier,callthe

firedepartment.

—Installationandservicemustbeperformedby

aqualifiedinstaller,serviceagency,orthegas

supplier.

FACTORYPRESETFORUSEWITH

NATURALGAS

Direct-VentAutomaticInstantaneousWaterHeater

(Chauffe-eauautomatiqueinstantanéàventilationdirecte)

FORINDOORINSTALLATIONONLY

(POURINSTALLATIONÀL'INTÉRIEURSEULEMENT)

120Volt,60Hz,5Amps

TypeofGas

(Typedegaz)

................

InputRating

(EntrerleClassement)

:Btu/hrMaximum...

Btu/hrMinimum...

MaximumInletGasPressure:............

MinimumInletGasPressure:............

MinimumInletGasPressure(foradjustments):..

MaximumWaterPressure:.............

MinimumWaterPressure:.............

RecoveryRating:..................

..................

ThermalEfﬁ

ciency/:

EnergyFactor:

NOxEmissions:

........

(PursuanttoSouthCoastAirQualityManagementDistrictRule1146.2)

(Moinsde20ppm)

(Jusqu'à98%/0.94)(Jusqu'à98%/0.94)

(Moinsde20ppm)

(Dégagementsminimums)

(Desnon-combustibles) (D'uneconstruction

combustible)

(conformémentaurèglement1146.2du"SouthCoastAirQualityManagementDistrict)

Topofheater

MinimumClearances

From

Non-Combustibles

FromCombustible

Construction

(Dessusduchauffe-eau)

Backofheater

(Arrièreduchauffe-eau)

Frontofheater

(Avantduchauffe-eau)

Bottomofcabinet

(Côtécanalisation)

Side(Côté)

5/8in(15.8mm)

6in(15.2cm)

2in(50.8mm)

12in(30.4cm)

5/8in(15.8mm)

6in(15.2cm)

2in(50.8mm)

1/2in(12.7mm)

12in(30.4cm)

IntellihotGreenTechnologiesInc.

2900W.MainSt.

Galesburg,IL61401

Phone:(877)835-1705

Email:info@intellihot.com

Web:www.intellihot.com

FactoryPreset

NaturalGas

(Réglageenusinepourgaznaturel)

199,000

20,000

13.0W.C.(3.20kPa)

8.0W.C.(2.00kPa)

150psi(1034kPa)

15psi(103kPa)

265GPH(1003LPH)

Upto98%/0.94

Lessthan20ppm

FieldConversion*to

PropaneGas

(Conversion*surplaceaugazpropane)

199,000

20,000

10.5W.C.(2.62kPa)

3.0W.C.(0.76kPa)

11.0W.C.(2.74kPa)

150psi(1034kPa)

15psi(103kPa)

265GPH(1003LPH)

Upto98%/0.94

Lessthan20ppm

CheckBoxif

Convertedto

PropaneGas

*RefertoInstallationandOperation

manualforconversionprocedure.

(Seréféreraumanueld'installationet

defonctionnementpourlaprocédurede

conversion.)

PRÉRÉGLAGESD'USINEPOURUTILISATIONAVEC

GAZNATUREL

(Pressiondegazd'arrivéemaximum)

(Pressiond'eaumaximum)

(Pressiond'eauminimum)

(Caractéristiquederecouvrement)

(Efficacitéthermique/Facteurénergétique)

(ÉmissionsdeNOx)

(Pressiondegazd'arrivéeminimum)

(Pressiondegazd'arrivéeminimum(pourajustements))

Cocherlacasesiconvertiaugazpropane

ETLSTICKER

SerialNumber:

IGT-LBL-0005-01

(Numérodesérie)

(CollantETL)

Operation and

Installation

Manual

Model: i200,i250

i200p, i250p

ThisproductcomplieswithANSIZ21.10.3 (2011)/CSA

4.3 GasWaterHeater. Foruse as potablewater heating.

TheEnergyStarratingapplies onlytothei200model.

—Nepasentreposerniutiliserd’essenceou

nid’autresvapeursouliquides inflammables

àproximitédecetappareiloudetout autre

appareil.

QUEFAIRESIVOUSSENTEZUNEODEURDEGAZ

•

Nepastenterd’allumer d’appareil.

•

Net

ouchez àaucuninterrupteur;nepasvous

servirdestéléphonessetrouvantdans

lebâtiment.

•

Appelezimmédiatementvotrefournisseurde gaz

depuisunvoisin.Suivezl

esinstructions

dufournisseur.

•

Sivousnepouvezrejoindrelefournisseur,

appelezleservice desincendies.

—L’installationet l’entretien doiventêtreassurés

paruninstallateurouunserviced’entretien

qualifiéouparlefournisseurdegaz.

AVERTISSEMENT

Assurez-vousdebiensuivrelesinstructionsdonnées

danscettenoticepourréduireauminimumle

risqued’incendieoud’explosionoupour évitertout

dommagematériel,touteblessureoulamort.

SPARES

WARNING

Condensate drain line (2) is shipped from the factory with

a loop held together with plastic ties. Do not remove the

ties and/or straighten the loop. This loop forms an air

block (trap) which prevents carbon monoxide from exiting

the water heater through the drain line. Improper

installation of the drain line can result in excessive levels of

carbon monoxide, which can lead to severe personal injury

or death.

1.2 Contact Information

Call us first if you have any questions about this product. We

can help you with questions about installation or operation,

or if there are damaged or missing parts when you unpack

this unit from the shipping box.

Stamp or write your dealer contact information here for future

reference.

Due to our policy of continuous product improvement and

technology, the design and/or technical specifications are

subject to change without notice.

Serial Number: ___________________________________

Date of Installation: ___ / ___ / ______

1.3 Serial Number Plate Locations

Rating plate contains serial number for the unit. Please

provide this serial number when calling for service or

warranty.

Rating and safety information inside.

(Caractéristiqueset renseignements de sécurité à l'intérieur)

FACTORY PRESET FOR USE WITH

NATURAL GAS

Direct-Vent Automatic Instantaneous Water Heater

(Chauffe-eauautomatique instantané à ventilation directe)

FOR INDOOR INSTALLATIONONLY

(POURINSTALLATION À L'INTÉRIEUR SEULEMENT)

120 Volt,60 Hz, 5 Amps

Type of Gas

(Typede gaz)

. . . . . . . . . . . . . . . .

Input Rating

(Entrerle Classement)

: Btu/hr Maximum . . .

Btu/hr Minimum . . .

Maximum Inlet Gas Pressure: . . . . . . . . . . . .

Minimum Inlet Gas Pressure: . . . . . . . . . . . .

Minimum Inlet Gas Pressure (for adjustments): . .

Maximum Water Pressure: . . . . . . . . . . . . .

Minimum Water Pressure: . . . . . . . . . . . . .

Recovery Rating: . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . .

Thermal Efﬁ

ciency / :

Energy Factor:

NOx Emissions:

. . . . . . . .

(Pursuantto South Coast Air Quality Management District Rule 1146.2)

(Moinsde 20 ppm)

(Jusqu'à98 % / 0.94) (Jusqu'à 98 % / 0.94)

(Moinsde 20 ppm)

(Dégagementsminimums)

(Desnon-combustibles) (D'une construction

combustible)

(conformémentau règlement 1146.2 du "South Coast Air Quality Management District)

Topof heater

Minimum Clearances

From

Non-Combustibles

FromCombustible

Construction

(Dessusdu chauffe-eau)

Backof heater

(Arrièredu chauffe-eau)

Frontof heater

(Avantduchauffe-eau)

Bottomof cabinet

(Côtécanalisation)

Side(Côté)

5/8in (15.8 mm)

6in (15.2 cm)

2in (50.8 mm)

12in (30.4 cm)

5/8in (15.8 mm)

6in (15.2 cm)

2in (50.8 mm)

1/2in (12.7 mm)

12in (30.4 cm)

Intellihot Green TechnologiesInc.

2900 W. Main St.

Galesburg, IL 61401

Phone: (877) 835- 1705

Email: [email protected]

Web: www.intellihot.com

Factory Preset

Natural Gas

(Réglageen usine pour gaz naturel)

199,000

20,000

13.0 W.C. (3.20 kPa)

8.0 W.C.(2.00 kPa)

150 psi (1034 kPa)

15 psi (103 kPa)

265 GPH (1003 LPH)

Up to 98% / 0.94

Less than 20 ppm

Field Conversion* to

Propane Gas

(Conversion*sur place au gaz propane)

199,000

20,000

10.5 W.C. (2.62 kPa)

3.0 W.C. (0.76 kPa)

11.0 W.C. (2.74 kPa)

150 psi (1034 kPa)

15 psi (103 kPa)

265 GPH (1003 LPH)

Up to 98% / 0.94

Less than 20 ppm

Check Box if

Convertedto

PropaneGas

*Referto Installation and Operation

manualfor conversion procedure.

(Seréférer au manuel d'installation et

defonctionnement pour la procédure de

conversion.)

PRÉRÉGLAGESD'USINE POUR UTILISATION AVEC

GAZ NATUREL

(Pressionde gaz d'arrivée maximum)

(Pressiond'eau maximum)

(Pressiond'eau minimum)

(Caractéristiquede recouvrement)

(Efficacitéthermique / Facteur énergétique)

(Émissionsde NOx)

(Pressionde gaz d'arrivée minimum)

(Pressionde gaz d'arrivée minimum (pour ajustements))

Cocherla case si converti au gaz propane

ETL STICKER

Serial Number:

IGT-LBL-0005-01

(Numérode série)

(CollantETL)

5 Safety Section

2. Safety

2.1 Safety Signal Words

DANGER

Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury. This signal

word is limited to the most extreme situations.

WARNING

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

NOTICE

Indicates that equipment or property damage can result if

instructions are not followed.

SAFETY

INSTRUCTIONS

Safety instructions (or equivalent) signs indicate specific

safety-related instructions or procedures.

Note: Contains additional information important to a

procedure.

2.2 Installation Warnings

WARNING

DO NOT use this water heater for any purpose other than

water heating.

Read, understand, and follow the Installation and Operation

manuals, including all warnings and precautions, before

operating this water heater. If you do not follow these

instructions exactly, a fire or explosion may result, causing

property damage, personal injury, or loss of life.

Follow all local codes and the most recent edition of the

National Fuel Gas Code (ANSI Z223.1/NFPA 54) in the USA or

the Natural Gas and Propane Installation Code in Canada

(CSA B149.1).

This water heater must be installed by a licensed plumber,

gas fitter, and/or professional service technician. Installation

by unqualified person(s) voids the warranty.

DANGER

A. This water heater does not have a pilot. It is equipped

with an ignition device which automatically lights the

burner. Do not try to light the burner manually.

B. BEFORE OPERATING, smell all around the water heater

area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire or

police department.

C. Use only your hand to turn the manual gas shut-off

valve. Never use tools. If manual gas shut-off valve will

not turn by hand, don’t try to repair it. Call a qualified

service technician. Force or attempted repair may

result in a fire or explosion.

WARNING

DO NOT use or store flammable liquids around the water

heater, including gasoline, oils, spray paints, etc.

DO NOT operate this water heater unless it is properly

vented to the outside (the exhaust vent piping must be

connected from the unit directly to the outside). Improper

venting can cause a build-up of carbon monoxide, which

can result in brain damage or death. Exhaust gases must

be completely expelled out of the building.

This water heater is factory preset for NATURAL GAS but

may be field converted for use with propane. For propane

conversion, refer to the Propane (LPG) Conversion section

of this manual. Connecting the water heater to any other

gas supply can result in property damage, serious injury,

or even death.

This water heater is suitable for use in potable water

heating applications. The cold and hot water fittings on

the top of the water heater MUST NOT be connected to any

heating system.

The water heater temperature is factory set to 120°F

(49°C). Hot water temperatures above 125°F can cause

severe burns instantly or death from scalds. If the

proposed water heater outlet temperature is to be set

above 125°F, installation of a thermostatically controlled

(or temperature limiting) mixing valve is recommended for

all hot water going to faucets to avoid the risk of scalding.

Examples include commercial applications where 140°F

(60°C) is often needed or if the space heating temperature

required is higher than the domestic hot water. Always

check the temperature of the hot water before bathing,

showering, washing, etc.

Protect against snow and debris accumulation around the

vent terminations. Regularly inspect the exhaust vent

pipe and the air intake pipe to ensure they remain clear

from obstructions at all times.

Safety Section 6

CAUTION

Make sure you know the location of the gas shut-off valve

and how to operate it. Immediately close the gas shut-off

valve if the water heater is subjected to fire, overheating,

flood, physical damage, or any other damaging condition

that might affect the operation of the unit. Have the water

heater checked by a qualified technician before resuming

operation.

If the water quality is known to have high acidity and/or

high hardness, water treatment is recommended. Consult

the local water authority.

SAFETY

INSTRUCTIONS

DO NOT use this appliance if any part has been under

water.

DO NOT reverse the cold water and gas connections as this

will damage the gas valve.

DO NOT overtighten fittings as damage may occur, causing

internal leakage.

The appliance should be located in an area where leakage

within the unit or at its connections will not result in

damage to the surrounding area. The manufacturer will

not be responsible for any damage resulting from leaking

if adequate drainage is not provided.

7 i200, i250, i200P, i250P Technical Data

3. Technical Data

3.1 Specifications Chart

Type

Fuel

Minimum / Maximum Input (Btu/h) 30,000 / 199,950 30,000 / 250,000

Thermal Eﬃciency 94% 92%

Energy factor 0.93 N/A

Dimensions H X W X D (inches)

Weight

Water and Gas connecons

Minmum Flow Rate

Venng Materials

Max 3” Vent Length - Single Pipe / Power Vent

200 , deduct 5  per 90° elbow 130 , deduct 5  per 90° elbow

Max 3” Vent Length - Two pipe / Direct Vent

100 , deduct 5  per 90° elbow 65 , deduct 5  per 90° elbow

Max 2” Vent Length - Single Pipe / Power Vent (2” not allowed at elevaons

above 4,000 )

26 , deduct 5  per 90° elbow

Max 2” Vent Length - Two Pipe / Direct Vent (2” not allowed at elevaons

above 4,000)

21 , deduct 5  per 90° elbow

Safety

Water Pressure Min / Max (PSI)

NG/LP- Minimum Stac Gas Pressure 1/2" black iron (non-corrugated) 5" 6"

NG/LP- Minimum Stac Gas Pressure 3/4" black iron (non-corrugated)

NG/LP - Maximum Stac Gas Pressure

Gas Pressure for Adjustments

Electrical

Power Consumpon

Features & Performance i200 i250

Recirculaon

Cascading

Heat exchanger

Hot Water Capacity (35F Rise) 10.8 13.2

Hot Water Capacity (45F Rise) 8.4 10.3

Hot Water Capacity (77F Rise) 5.0 6.0

Domesc Hot Water Temp. Sengs

Warranty (with recirculaon)

30 / 150

26 X 17.4 X 14.9 (3.9 cu. )

Parameter

i200, i200P

i250, i250P

Indoor, Wall hung, Fully Condensing, direct igniton

Preset for NG / LP converble

2.5"

"P" models - 98 lbs, Non "P" models - 93 lbs

3/4" NPT

"P" models - No min. ﬂow / Non "P" models - 0.6 GPM

Sch. 40 PVC, Sch. 40 CPVC, Polypropylene, Stainless Steel

N/A

Flame Rod, Thermal Fuse, Overheat Prevenon Device, Fan Speed Monitor, Flue Temperature

Monitor, Blocked Vent Detector, Water Shut Oﬀ Valve, 2X10A Fuse, Dual Flame Sensing

Note: Due to Intellihot's Policy of continuous product improvements, design and technical specifications are subject to change without notice

14”

8" for NG, 11" for LP

120V AC, 60 Hz

500W (Max 4.2 Amps), 8W (Standby)

Masterless, 10 units

Built-in pump for "P" models

Stainless 316L

100 – 185°F

Residenal - Heat Exchanger coil - 15 years, Parts – 5 years, Labor – 1 year

Commercial - Heat Exchanger coil – 6 years, Parts – 3 years, Labor – 1 year

3.2 High Elevation Installations

For operation at elevations above 2,000 feet, the hot water

delivery capacity should be reduced by 4% for each 1,000 feet

above sea level.

i200, i250, i200P, i250P Technical Data 8

3.3 Dimensional Specifications

26"

FRONT VIEW

BOTTEM MOUNTING

BRACKET

SIDE VIEW

POWER CORD

CONDENSATE DRAIN

MOUNTING WALL SURFACE

TOP VIEW

HOT WATER OUT

3/4 NPT

COLD WATER IN

3/4 NPT

FRESH AIR INTAKE 3"

EXHAUST PORT 3"

GAS INLET

3/4 NPT

BOTTEM VIEW

CONDENSATE DRAIN

POWER CORD

3/4” DRAIN

9 i200, i250, i200P, i250P Technical Data

3.4 Connections

Item Description Specification1

1 Hot Water Outlet Connection 3/4” Male NPT

2 Exhaust Gas Vent 3” O.D.

3 Gas Supply Inlet Connection 3/4” Male NPT

4 Gas Pressure Analyzer Port 1/8” Female NPT

5 Fresh Air Intake 3” O.D.

6 Access Ports for Blower Mounting

Screws

—

7 Water Inlet Strainer —

8 Cold Water Supply Inlet Connection 3/4” Male NPT

9 Power Supply —

10 Condensate Drain Connection 3/4” Nipple (3/4” flex hose)

11 3/4” Drain Connection 3/4” Female NPT

1Using sizes other than specied can cause damage to the water

heater and will void the warranty.

IQ-012

IQ-102

10 11

Installation Preparation 10

4. Preparation Before Installation

4.1 Selecting an Installation Site

Note: When installing the water heater, follow all local

building codes and the current edition of the National

Fuel Gas Code (ANSI Z223.1/NFPA 54) in the USA, or

National Gas and Propane Installation Code (CAN/CGA

B149.1) in Canada when installing this product.

Note: For water heater installations in Massachusetts, the

unit must be installed by a plumber or gas-fitter

licensed within the Commonwealth of Massachusetts.

Refer to the Requirements for the State of

Massachusetts section in this manual for additional

information.

1. Select an interior location for the installation. Each

installation is unique; therefore, take the time to find the

best location for the water heater.

a. Install the water heater near locations that use hot

water, such as bathroom, kitchen, or laundry room

faucets.

b. Select a location that minimizes the length of the water

pipe.

c. If the distances are long or if the faucet or appliance

requires “instant” hot water, we recommend running

a recirculation line back to the water heater from the

farthest fixture.

d. Insulate the hot water supply and recirculation lines.

e. Select a location away from foot traffic and away from

areas where dust, debris, chemical agents, or other

combustible materials could accumulate.

f. Allow sufficient space for service and maintenance

access to all gas, water, and drain connections.

g. Make sure the location meets all building code

requirements.

h. Make sure the wall surface that the water heater is

mounted on will support the weight of the unit

(90 lbs. minimum).

2. Minimize the distance that the exhaust gas vent and fresh

air intake must travel to an exterior wall.

a. The exhaust vent outlet must not be located next

to a walkway, near soffit vents, crawl space vents,

or other areas where condensate (water vapor)

could cause damage or create a hazard. Refer to the

Venting Clearance Specications section for additional

information.

b. The fresh air inlet vent must be located at least 12”

from the exhaust vent.

c. Contaminated or dirty air drawn into the intake pipe

can damage the water heater. The warranty does not

cover damage caused by airborne contaminants.

3. Locate the unit close to a drain and near gas and water

connections.

The water heater produces a significant amount of

condensate during normal operation and should be

located near a suitable drain where damage from a

possible leak will be minimal. Installing the water heater

in a location without a drain will void the warranty

and the manufacturer will not be responsible for any

resulting water damages that may occur. For additional

information, refer to the Condensate Line Installation

section.

4. Locate the water heater and all the water pipes in an area

where the ambient temperature always remains above

freezing.

a. When the water heater is connected to an electrical

power supply, it will automatically prevent the water

from freezing inside the unit.

b. The unit’s freeze protection system will not prevent the

water in surrounding pipes from freezing.

NOTICE

In cold climates, if there is a power failure, the unit’s freeze

protection system will not operate and can result in water freezing

inside the heat exchanger. To prevent damage to the water

heater, turn OFF the gas supply and inlet water valve. Completely

drain the unit. Damage caused by freezing water is not covered

by the warranty.

5. Select an appropriate location for the combustion air and

exhaust pipes to exit the building, as shown in the Venting

Clearance Specications section in this manual.

Altri manuali per i200

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Intellihot Scaldabagno

Intellihot

Intellihot iN199 Manuale utente

Intellihot

Intellihot iN199A Manuale utente

Intellihot

Intellihot iN401 Manuale utente

Intellihot

Intellihot iE1 Manuale utente

Intellihot

Intellihot i200X Manuale utente

Intellihot

Intellihot iQ250D Scheda tecnica

Intellihot

Intellihot Combi i201X* Manuale utente

Intellihot

Intellihot Legionator iL3.5 Guida rapida

Intellihot

Intellihot i200 Manuale utente

Intellihot

Intellihot iQ1001 Scheda tecnica

Intellihot

Intellihot Legionator iL3.5 Guida rapida

Manuali Scaldabagno popolari di altre marche

Kenmore

Kenmore 153.582400 Manuale utente

Applimo

Applimo Edel AIR Manuale utente

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manuale utente

clage

clage E-Mini Series Manuale utente

Toyotomi

Toyotomi Oil Miser OM-180 Manuale utente

Bradford White

Bradford White EF Series Manuale utente

Eccotemp

Eccotemp 40-H Manuale utente

Dimplex

Dimplex ECSd125-580 Guida

Dux

Dux 32FCR6N Manuale utente

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guida alla risoluzione dei problemi

Noritz

Noritz N-132M Manuale di istruzioni

TESY

TESY GCV7/4S 10047 Scheda tecnica

A.O. Smith

A.O. Smith Gphe 50 Manuale utente

Koryo

Koryo KWHZF15Y Manuale utente

Pentair

Pentair PSC-14-4-02 Manuale utente

GE 40M06AAG Istruzioni per il montaggio

Thermor

Thermor AEROMAX SPLIT 2 Manuale utente

American Hometec

American Hometec AHQ-B03X Manuale utente

Intellihot i200 Scheda tecnica

Manuali Scaldabagno popolari di altre marche