Intenda Box Modulare Manuale utente
INSTALLATION MANUAL. USE AND MAINTENANCE
BOX MODULARE
BOX MODULARE ECO
INTENDA S.r.l.
Via V. Pareto, 3
37045 S. Pietro di Legnago (VR)
Tel +39 0442 601031 – 600270
Fax +39 0442 25164
2
TABLE OF CONTENTS
1. GENERAL INFORMATION ..................................................................................................... 3
1.1 Introduction............................................................................................................................ 3
1.2 General precautions regarding the use of the product ........................................................... 4
1.3 Structure of the manual ......................................................................................................... 4
1.4 Product identification......................................................................................................... 5
1.5 Warranty............................................................................................................................... 5
2. BOX DESCRIPTION AND TECHNICAL SHEET..................................................................... 6
2.1 General description ............................................................................................................... 6
2.2 Components.......................................................................................................................... 7
2.3 Fabric’s characteristics ........................................................................................................ 10
3. INSTALLATION........................................................................................................................ 12
3.1. Handling and transport ....................................................................................................... 12
3.2. Place and requirements for the installation ...................................................................... 12
3.3. Installation ....................................................................................................................... 12
3.3.1. Package opening ......................................................................................................... 12
3.3.2 Squared holding devices placement.............................................................................. 13
3.3.3 Box installation.............................................................................................................. 13
3.4 Bracing system.................................................................................................................... 14
3.5 Snails opening..................................................................................................................... 15
4. GENERAL SAFETY PRINCIPLES ........................................................................................ 16
5. BOX USAGE ......................................................................................................................... 17
6. CHECKS AND MANTAINANCE............................................................................................ 17
6.1. ORDINARY MAINTENANCE.............................................................................................. 18
7. DISASSEMBLY..................................................................................................................... 19
3
1. GENERAL INFORMATION
1.1 Introduction
This manual is an integral part of the product; it is addressed to the installer and to the final user of
the box, and enables a correct installation and use. For this reason it must be hold with the box until
proper disposal.
In this manual you will find the instructions to:
•correctly install the box
•understand the functions of the box and of the whole thereof
•correctly do the box scheduled maintenance processes
•take care of the basic safety rules
ATTENTION: the installer and the final user must read the whole manual in each part of
it. Keep this manual in a safe and accessible place.
Before using the box, please read carefully the technical information contained in this
manual and follow them strictly.
The manual must be kept with care, disseminated and made available to all interested persons. In
harmony with the overall design of the structure, the manual was created in full compliance with the
directives of the European Community.
This manual contains the main information indicated in the index, it is an integral part of the Box and
must be kept with care until the final dismantling of the structure itself in order to allow reference for
future updates. In the event of damage that makes the copy of the manual in its possession unusable,
the user can request a copy from Intenda S.r.l., specifying the type of structure, the serial number or
order shown on the nameplate of the structure itself.
No responsibility is assumed for translations into other languages which do not conform to the
original meaning.
This manual reflects the state of the product at the time of supply and cannot be considered
inadequate only because it is subsequently updated on the basis of new studies or experiences. You
will receive, in the future, revisions or updates to integrate and consider. Intenda S.r.l. reserves the
right to update production and manuals without the obligation to update the production and previous
manuals and without the obligation to inform users of the equipment previously supplied. The
notification of proposals for updating the manual and / or the machines are in any case to be
considered a courtesy. The customer assistance service is however available to provide, upon
request, information on the updates that Intenda S.r.l. made to the products.
This manual has been created in order to provide the user with a general knowledge of the product
and the maintenance instructions deemed necessary for its proper functioning. Before proceeding
with functional operations, maintenance and repairs, carefully read the Manual. It contains all the
information necessary for the correct use of the product and to avoid accidents. The control and
maintenance frequencies prescribed by the manual are always intended as the minimum necessary
to ensure the efficiency, safety and durability of the product in normal working conditions. The
surveillance must in any case be constant and prompt action must be taken in the event of
anomalies.
WARNING: Any modification or tampering, not authorized by the manufacturer, to the product and
to the safety or structural systems, cancels any responsibility of the manufacturer with regard to CE
conformity.
4
1.2 General precautions regarding the use of the product
These indications are part of the normal behavior that workers must have towards the product and
therefore in the design and construction of the product, the manufacturer considered them known to
the tenant. It is the user's task to inform (by delivering this manual) and train the employees (users
and maintenance technicians) so that these indications are brought to the attention of the staff who
will work with the structure.
- Always use anti-cut gloves when closing or opening the structure, during adjustments or
maintenance (described in the following chapters). When finished, wash your hands with soap and
water.
- Immediately clean any accidental contacts of corrosive products that come into contact with the
structure to avoid rapid deterioration.
- Do not allow unauthorized personnel to work with the equipment.
- Before using the equipment, make sure that any dangerous to safety conditions have been properly
eliminated.
- Make sure that all the guards and other protections as well as the structural fixings are in place and
that all the safety devices are present and efficient.
- Make sure that there are no foreign objects in the sliding area of the structure.
- Individual protection devices must be used such as:
o Safety clothing
o Safety shoes
o Cut resistant gloves
The protection systems must be used in the following phases:
- Structure maintenance operations (cleaning, checking or adjustment)
- Operating operations (closing and opening)
1.3 Structure of the manual
This manual consists of eight parts which contain:
• 1. GENERAL RULES AND WARNINGS, useful premises for using and understanding the manual;
• 2. GENERAL INFORMATION, useful premises for identifying the box;
• 3. TECHNICAL DATA, information on the characteristics of the box;
• 4. OPERATING INSTRUCTIONS, interface for the safe use of the box;
• 5. MAINTENANCE, advices and recommendations;
• 6. DEMOLITION AND DISMANTLING OF THE STRUCTURE, instructions and recommendations;
• 7. SPARE PARTS, detailed list of the parts that make up the box.
The user manual makes use of the following typographical conventions:
5
Symbol Indicates
Note
WARNING
ATTENTION
1.4 Product identification
The physical identification record is the silk-screened and stamped plate which contains the details
to be cited, in case of need, to the company Intenda S.r.l . This plate is the only one recognized by
the manufacturer as a means of product identification. For no reason the data shown on the
product can be altered. A reproduction of the plate is shown in the following drawing.
1.5 Warranty
Intenda’s products are guaranteed as by law, with effect from the date stated on the invoice.
During this period INTENDA S.r.l. will remove in an appropriate time all vices and defects of the
materials and/or of the building process, only if the box:
•has been installed by qualified workers
Notes contain important information highlighted outside
the text. Pay close attention.
Warning messages contain procedures, indicated in
the manual, that failure to observe can result in
equipment damage.
The ATTENTION messages indicate the particular
procedures whose failure to comply can damage the
operator.
6
•has been used correctly, following the conduct and maintenance indications contained in this
manual
•has not been subjected to natural disasters
To remove the defects found out during the warranty time:
•the costs of working time and transport are at the expense of the dealer
•the costs of spare parts are at the expense of INTENDA S.r.l.
Warranty is meant to be ex works Legnago (VR). All the tools and optional parts eventually supplied
by the dealer are not subject to the warranty.
In the box building process INTENDA S.r.l. uses materials and mechanisms of suitable type, state
and quality, at its own discretion; even after the receipt of the order, INTENDA S.r.l. can make
substantial changes or appropriate improvements at its own discretion.
Slight colour differences, folds or “partridge’s eyes” in the PVC clothes should not be considered
defects, but features of the article.
2. BOX DESCRIPTION AND TECHNICAL SHEET
2.1 General description
The box must be used only as an ordinary protection cover, for purely temporary use. In case of bad
weather conditions (wind, snow), the box must be removed. Given that the box can not be fixed to
the ground - but only bound to it - its use in these conditions can cause damages to people and
things.
It is particularly important for safety not to hang or apply any type of load at the structure or at the
top cover of the box.
In particular, children must not handle the snails. The failure to respect the conditions of use and
warnings immediately voids the warranty.
BOX MODULARE/BOX MODULARE ECO 1 snail
BOX MODULARE/BOX MODULARE ECO 2 snails
A (cm): 410/480/550
B (cm): 250
C (cm): 200
A (cm): 470/540/610
B (cm): 250
C (cm): 200
7
2.2 Components
N. DESCRIPTION
1 ALUMINIUM PROFILE MM 45X15
2 ALUMINIUM PROFILE (gables)
3 SQUARED HOLDING DEVICE
4 SQUARED HOLDING DEVICE CAP
5 ANODIZED ALUMINIUM 120x60 FOOT
6 PVC COVERSOL/FABRITARP TOP COVER
7 ALUMINIUM LACQUERED RAL 9010 PLATE (crosses)
8 ALUMINIUM LACQUERED RAL 9010 PLATE (tension bars)
9 NYLON ROPE DIAM. MM 5
10 STRING FASTENER HANDLE
11 HINGE FASTENING RIVET
12 TENTMESH LATERAL COVER (only for Box Modulare)
13 FOOT WITH FINAL HINGE
14 FOOT WITH CENTRAL HINGE
15 FOOT WITH HINGE FOR HEAD-FASTENING PLATE
8
9
10
8
7
12
9
10
2.3 Fabric’s characteristics
COVERSOL
BOX MODULARE
Yarn Warp: 100% PES 280 Dtex
Weft: 100% PES 280 Dtex
Fabric’s weight Ca 400 gr/m
2
Tensile strength Warp: Ca 120 DaN/5 cm
(DIN 53354) Weft: Ca 130 DaN/5 cm
Tearing resistance Warp: Ca 5,5 DaN
(DIN 53363) Weft: Ca 7,5 DaN
Grip (ISO 2411) Ca 6 DaN/5 cm
Temperature resistance +70°C/-30°C
Finishing Gloss lacquered (one side)
UV Treated
Altri manuali per Box Modulare
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Intenda Tenda
