Intermec EasyCoder 201II Manuale utente

EasyCoder 201 II

Memory Card Adapter Kit

P/N 1-960270-05

Edition 3

September 1998

Installation Instructions

EasyCoder 201 II – Installation Instructions

MEMORY CARD ADAPTER KIT

General Information This leaflet contains instructions on how to install a Memory Card

AdapterinanEasyCoder201IIorEasyCoder201IIEprinter.(The

adapter is fitted as standard in EasyCoder 201 IISA). This optional

device could be purchased as a kit for field installation by an

authorized technician. When such is the case, please follow the

present instruction sheets for maximum safety and performance.

Beforestartingtomodifyyourprinter,checkthattheMemoryCard

Adapter Kit is complete. It should include the following parts:

• 1 Memory Card Expansion Board

• 1 Memory Card Holder

• 1 Connection Cable

• 1 Address Decoder GAL 20V8

• 3 Screws

• 3 Washers

• This instruction booklet

Information in this manual is subject to change without prior notice and does

not represent a commitment on the part of Intermec Printer AB.

©CopyrightIntermecPTCAB,1998.Allrightsreserved.PublishedinSweden.

EasyCoder is a registered trademark of Intermec Technologies Corp.

EasyCoder 201 II

Memory Card Adapter Kit

Installation Instructions

Edition 3, September 1998

Part No. 1-960270-05

EasyCoder 201 II – Installation Instructions

❑Turn off the power . For extra safety, pull the power cord out of

the mains receptacle at the rear plate of the printer.

❑Open the right-hand door.

❑Loosen the two screws that hold the cover.

❑Pull out the cover. The left-hand door can be swung open, and

the logic part of the printer becomes accessible.

❑Loosen the front plate by unscrewing the five screws indicated

on the drawing below. Disconnect the display and keyboard

cables from their connectors on the CPU board.

MEMORY CARD ADAPTER KIT, cont'd.

Step-by-Step Installation

Instructions

CPU Board

Screws (2x)

Cover

Continued!

EasyCoder 201 II – Installation Instructions

MEMORY CARD ADAPTER KIT, cont'd.

Step-by-Step Installation

Instructions, cont'd. ❑Fit the Address Decoder on the Memory Card Board.

❑Insert the Memory Card Board into the Memory Card Holder.

❑Place the front plate upside down on the table.

❑Fasten the Memory Card Adapter assy. to the front plate by

means of the three screws with washers. Position the adapter at

appr. 16–17 mm (0.65") from the edge of the front plate, as

illustrated below.

❑Fitthe40-lineFlatCabletoconnectorP-1oftheMemoryCard

Adapter (see above).

Connector (P-1)

Address Decoder

Memory Card Board Memory Card Holder

Continued!

16 to 17 mm

(0.65")

Screws & Washers (3x)

EasyCoder 201 II – Installation Instructions

MEMORY CARD ADAPTER KIT, cont'd.

Step-by-Step Installation

Instructions, cont'd. ❑Mount the front plate back on the printer.

❑ConnectthecablefromtheMemoryCardAdaptertoconnector

P-2 on the CPU board. Fit exactly as illustrated and make sure

that it cannot be damaged by moveable mechanical parts.

❑Connect the display and keyboard cables.

❑Close the left-hand door and the top cover in reverse order (see

page 2).

❑Check that a memory card can easily be inserted and pulled out

from the adapter.

❑Checkthat theright-handdoor isnotobstructed bythememory

card.

❑Closetheright-handdoor,andinsertthemainscable.Switchon

power. The printer is now ready for use.

WARNING!

Becarefultomounttheflatcable

that connects the CPU board to

the Memory Card Adapter as

illustrated. Reversal of a con-

nector may cause damage to

components.

IMPORTANT!

Always switch off the power before

fitting or removing a memory card.

The printer's firmware will not

detect a memory card unless it is

inserted during power-up.

Blue colour marking

CPU Board

Memory Card Adapter

Altri manuali per EasyCoder 201II

Indice

Altri manuali Intermec Etichettatrice

Intermec

Intermec EasyCoder PD41 Manuale utente

Intermec

Intermec EasyCoder PX4i Manuale utente

Intermec

Intermec EasyCoder PD4 Manuale utente

Intermec

Intermec EasyCoder 4420 Manuale utente

Intermec

Intermec 4400 Manuale utente

Intermec

Intermec EasyCoder 501XP Istruzioni operative originali

Intermec

Intermec EasyCoder PD4 Manuale utente

Intermec

Intermec PM43c Manuale utente

Intermec

Intermec EasyCoder 501 E Guida

Intermec

Intermec PB22 Manuale utente

Intermec

Intermec EasyCoder PC41 Manuale utente

Intermec

Intermec 3240 Manuale utente

Intermec

Intermec EasyCoder E4 Manuale utente

Intermec

Intermec EasyCoder E4 Linerless Manuale utente

Intermec

Intermec ColorCoder V4 Manuale utente

Intermec

Intermec 4630 Manuale utente

Intermec

Intermec EasyCoder PX4i Manuale utente

Intermec

Intermec EasyCoder E4 Manuale utente

Intermec

Intermec EasyCoder 4420 Manuale utente

Intermec

Intermec PB51 Manuale utente

Intermec

Intermec EasyCoder 401 Manuale utente

Intermec

Intermec EasyCoder 501 E Manuale utente

Intermec

Intermec EasyCoder 501XP Manuale utente

Intermec

Intermec EasyCoder PX6i Manuale utente

Manuali Etichettatrice popolari di altre marche

Brother

Brother P-Touch 2420PC Manuale utente

newell

newell Dymo LabelManager 210D Manuale utente

Brother

Brother TD-4000 Manuale utente

U-Line

U-Line BROTHER H-8754 Manuale utente

Tharo Systems

Tharo Systems H-435+ Manuale utente

Brother

Brother E300 Manuale utente

Godex

Godex RT700 SERIES Manuale utente

ID Technology

ID Technology 252 Manuale utente

Labelmate

Labelmate MC-11 Manuale utente

CAB

CAB XD4M/300 Manuale utente

Avery Dennison

Avery Dennison Pathfinder 6057 Manuale di servizio

Brother

Brother P-touch PT-9700PC Manuale utente

TSC

TSC PEX1000 Series Manuale utente

Adkins

Adkins Label Master Manuale utente

Epson

Epson LabelWorks LW-400 Manuale utente

Primera

Primera 510212 Manuale utente

Brady

Brady BradyPrinter S3100 Manuale utente

DuraLabel

DuraLabel LabPRO Manuale utente