Intermec PM23c Manuale utente
UART+Industrial Interface
PM23c
Installation Instructions
|PM43|PM43c
ii PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions
Intermec Technologies Corporation
Worldwide Headquarters
6001 36th Ave.W.
Everett, WA 98203
U.S.A.
www.intermec.com
The information contained herein is provided solely for the purpose of allowing
customers to operate and service Intermec-manufactured equipment and is not to be
released, reproduced, or used for any other purpose without written permission of
Intermec Technologies Corporation.
Information and specifications contained in this document are subject to change
without prior notice and do not represent a commitment on the part of Intermec
Technologies Corporation.
© 2012–2013 by Intermec Technologies Corporation. All rights reserved.
The word Intermec, the Intermec logo, Norand, ArciTech, Beverage Routebook,
CrossBar, dcBrowser, Duratherm, EasyADC, EasyCoder, EasySet, Fingerprint, INCA
(under license), i-gistics, Intellitag, Intellitag Gen2, JANUS, LabelShop, MobileLAN,
Picolink, Ready-to-Work, RoutePower, Sabre, ScanPlus, ShopScan, Smart Mobile
Computing, SmartSystems, TE 2000, Trakker Antares, and Vista Powered are either
trademarks or registered trademarks of Intermec Technologies Corporation.
There are U.S. and foreign patents as well as U.S. and foreign patents pending.
PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions 3
Install the UART+Industrial Interface
Board
Use these instructions to install the UART+Industrial interface
board in Intermec PM23c, PM43, and PM43c printers.
You will find these items in the shipping box:
You will need the following tools to install the interface board:
•T20 Torx screwdriver
•Small wrench
To install the UART+Industrial interface board, you need to
open the printer and physically install the board in the printer.
This board must only be installed by an authorized service
technician.
Follow standard ESD guidelines to avoid damaging the
equipment you are servicing.
Before you begin, turn off the printer and disconnect the
power cord and communication cables.
The electronic compartment contains wires and
components with dangerous voltage. Make sure that the
printer is switched off and the power cord is disconnected
before the cover is removed.
4 PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions
Open the Printer
You need to remove both the media cover and the electronics
cover to install the UART+Industrial interface board.
To remove the media cover
1Open the media cover.
2Use the small wrench to loosen the nut that secures the
media cover latches in place.
3Slide the latches counterclockwise into the open position.
4Close the media cover and lift it off the hinges.
5Put the media cover aside on a soft cloth to avoid scratches.
PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions 5
To remove the electronics cover
1Use a T20 Torx screwdriver to remove the two screws that
secure the electronics cover to the inside of the printer base.
2Use a T20 Torx screwdriver to remove the two screws located
on the outside of the electronics cover.
3Remove the electronics cover, and put the cover aside on a
soft cloth to avoid scratches.
6 PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions
To install the UART+Industrial interface board
1On the back of the printer, remove the two screws that secure
the cover plate to the printer, and remove the cover plate.
2Attach the spacer screw to the center of the printer main
board.
3Insert the UART+Industrial interface board into the printer
and use the T20 Torx screwdriver to secure the board
assembly to the printer with the two Torx screws removed in
Step 1.
4Use the T20 Torx screwdriver to secure the interface board
assembly to the spacer screw with a Torx screw.
PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions 7
5Insert the single or dual option board cable into the 80-pin
connector on the printer main board.
6Insert the other end of the option cable into the 80-pin
connector on the UART+Industrial interface board.
Note: You may need to use the dual option cable to connect
to the main board depending on which slot you use for the
UART+Industrial interface option board.
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
© 2013 Intermec Technologies
Corporation. All rights reserved.
7Install the jumpers and ICs on the board to configure it for the type of
serial communication you want to use:
8Replace the electronics cover.
9Replace the media cover.
To configure the board as: Install these jumpers and ICs:
RS-232 1Install a jumper on P3 so that the A is in the
middle of the jumper.
2Install IC, 360-028-001 (MAX238) on SKT3
with pin 1 located where the arrow points to
SKT3 toward the bottom of the board.
RS-422 1Install jumpers on P4 and P5.
2Install IC, 360-027-001 (MAX1490), across
sockets SKT1 and SKT4 with pin 1 located
where the arrow is pointing to SKT1 toward the
bottom of the board.
RS-485 1Install a jumper on P2.
2(Optionally) Install a jumper on P5 if this
printer is going to be connected to the end of
the cable.
3Install IC, 360-026-001 (MAX1480), across
SKT2 and SKT5 with pin 1 located where the
arrow is pointing to SKT2 toward the bottom
of the board.
PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions
*931-101-002*
P/N 931-101-002
Altri manuali per PM23c
3
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Intermec Apparecchiature di registrazione
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
