Intex Giraffe Manuale utente

WARNING: To reduce the risk of injury, user must read and understand operator’s manual.

Super Pads

Jost®

Dustless Sander Dust Extractors

WARNING!: Using or storing in the incorrect setting, will cause damage to the drive shaft & therefore void warranty.

IMPORTANT NOTICE!

HEAD POSITION A IS FOR SANDING CEILINGS

HEAD POSITION B IS FOR SANDING WALLS & STORAGE

(See page 9)

EXCESSIVE PRESSURE APPLIED TO SANDING

SURFACE MAY RESULT IN STRAIN & POSSIBLE

BREAKAGE TO THE DRIVE SHAFT.

(See page 9)

重要需知支头位置B 用于墙体打磨和仓储

改变支头到位置A 只用于顶棚在不正确的设置下使用或仓储，会引起驱动轴的损

坏，因此保修无效位置A 位置B

Operation Manual: 1-15

操作手冊:頁 16-31

2Intex Giraffe® intexinternational.com

Tuned Electronics

Intex Starmix® Dust Extractor

powers on/off automatically when

the Intex Giraffe® is switched on/

off. Lockable power switch enables

cruise control for continuous use.

Multi-Directional Sanding Head

Unique head adjusts to suit sanding position,

eliminating surface gouging and providing

maximum sanding efﬁciency. Position A for

ceilings; Position B for walls.

Speed Control

Variable speed control wheel

allows for rotational speed

adjusting for speed sensitive

applications. i.e. higher for more

aggressive work and lower

for ﬁner applications such as

in-between coat sanding. Soft

start-up electronics eliminate

swirl marks and gouging.

Intex Giraffe® Dustless Sander Intex Mini Giraffe® Dustless Sander

Code AG700 AG799

Voltage 230V/50Hz or 110V/60Hz 230V/50Hz or 110V/60Hz

Power Input 550 Watt 550 Watt

No Load Speed 650 ~ 1600 rpm 650 ~ 1600 rpm

Full Load Speed 280 ~ 950 rpm 280 ~ 950 rpm

Sanding Head Ø 215mm Ø 215mm

Sanding Disc Ø 225mm Ø 225mm

Net Weight 4.65 kg (10Lbs) 3.8 kg (8.36Lbs)

Perfect-Balance

Lightweight design is built

tough for the most demanding

conditions and signiﬁcantly

reduces effects of fatigue and

RSI, particularly during ceiling

operations.

CARTON CONTENTS

AG700/AG799 Intex Giraffe® Dustless Sander

AG001 Intex Giraffe® H/D Vacuum Hose - 4.3m

AG066B Intex Giraffe® Cushioned Interface Pad

AGHKEY6 Intex Giraffe® L-Hex 6mm Wrench Tool

MANAG700 Intex Giraffe® Instruction Manual

Superior Extraction Technology

Extraction system and Industrial

Grade construction is also

compatible for use in alternative

industries to drywall including

cement sheet, concrete and timber.

WARNING: To reduce the risk of injury, user must read and understand operator’s manual.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, ﬁre and/or serious injury. Save all warnings and instructions

for future reference. The term “power tool” in the warnings refers to your mains operated (corded)

power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to

lose control.

2) ELECTRICAL SAFETY

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodiﬁed plugs and matching outlets will

reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use an earth leakage circuit

breaker. Use of an earth leakage circuit breaker reduces the risk of electric shock.

3) PERSONAL SAFETY

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or medication.

A moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions

will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with

your ﬁnger on the switch or energising power tools that have the switch on invites accidents.

4Intex Giraffe® intexinternational.com

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a. Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery pack from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the

hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts

and any other condition that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

5) SERVICE

Have your power tool serviced by an Authorised Service Center, using only identical and genuine Intex

Giraffe® replacement parts.

NOTE: We recommend the power tool be serviced at least once per year. This will ensure that the safety

and operation of the power tool is maintained.

WARNING: To reduce the risk of injury, user must read and understand operator’s manual.

SPECIFIC SAFETY RULES

1. Keep hands away from rotating sanding head area at all times!

2. Prolonged breathing of airborne dust from drywall sanding may effect respiratory function:

Always use a vacuum cleaner with a bag approved for drywall dust installed.

Always wear a respirator approved for dust and mist.

3 . Sanding LEAD-BASED paint is extremely toxic and should not be attempted. Only allow

professionals with special training and equipment perform this task.

4. Maintain proper footing and balance at all times. Do not overreach. Use proper scaffolding.

5. Always wear appropriate safety equipment when operating.

6. Important: After completing sanding, switch off the switch and wait for the coasting sanding

head to stop completely before putting the tool down.

7. Never operate the tool in an area with ﬂammable solids, liquids, or gases. Sparks from the

commutator/carbon brushes could cause a ﬁre or explosion.

8. There are certain applications for which this tool was designed. The manufacturer strongly

recommends that this tool NOT be modiﬁed and/or used for any application other than for which

it was designed. If you have any questions relative to its application DO NOT use the tool until you

have written the manufacturer and have been advised.

9. Use the machine with both hands at all times. Loss of control can cause personal injury.

10. Keep power supply cord clear from the working range of the machine. Always lead the cable

away behind you.

11. Immediately switch off the machine if unusual vibrations or if other malfunctions occur. Check

the machine in order to ﬁnd out the cause.

12. The dust that arises when working with this tool can be harmful to health. Use a dust absorption

system and wear a suitable dust protection mask and remove deposited dust with a vacuum

cleaner.

SYMBOLS USED IN THIS MANUAL

V volts

A amperes

Hz hertz

W watt

~ alternating current

n0 no load speed

min-1 revolutions or reciprocation per minute

warning of general danger

class II tool

with electrical earth

read these instructions

always wear eye protection

always wear a dust mask.

always wear hearing protection

wear safety-approved hard hat

do not dispose of electric

tools,accessories and packaging

together with household waste material

6Intex Giraffe® intexinternational.com

FUNCTIONAL DESCRIPTION

This Electric Dustless Power Sander is specially designed for the most efﬁcient sanding of drywall

or plaster walls and ceilings for both new construction and renovation work. It is designed to work in

conjunction with a vacuum cleaner for minimum dust and best sanding results. The pivoting sanding

head allows excellent results with minimum time and effort.

For superior dust extraction, we recommend the german made range of Intex starmix®

dust extractors/vacuums.

ELECTRICAL CONNECTION

The network voltage must conform to the voltage indicated on the tool name plate. Under no

circumstances should the tool be used when the power supply cable is damaged. A damaged cable must

be replaced immediately by an authorized Customer Service Center. Do not try to repair the damaged

cable yourself. The use of damaged power cables can lead to an electric shock.

EXTENSION CABLE

If an extension cable is required, it must have a sufﬁcient cross-section so as to prevent an excessive

drop in voltage or overheating. An excessive drop in voltage reduces the output and can lead to failure of

the motor.

The following table shows you the correct cable diameter as a function of the cable length for this

machine. Use only U.L. and CSA listed extension cables. Never use two extension cables together.

Instead, use one long one.

Total Extension Cord Length (feet) Cord Size (AWG)

25 16

50 12

100 10

150 8

200 6

Super Pads

Jost®

Dustless Sander

Dust Extractors

WARNING: To reduce the risk of injury, user must read and understand operator’s manual.

UNPACKING

Carefully remove the tool and all loose items from the shipping container.

Retain all packing materials until after you have inspected and satisfactorily operated the machine.

CARTON CONTENTS

AG700/AG799 - Intex Giraffe® Dustless Sander

AG001 - Intex Giraffe® H/D Vacuum Hose - 4.3m

AG066B - Intex Giraffe® Cushioned Interface Pad

AGHKEY6 - Intex Giraffe® L-Hex 6mm Wrench Tool

MANAG700 - Intex Giraffe® Instruction Manual

DO NOT OPERATE THIS TOOL UNTIL YOU READ AND UNDERSTAND

THE ENTIRE INSTRUCTION MANUAL

TO REPLACE SUPER PAD ABRASIVE

1. Unplug the machine.

2. Peel away the worn out sandpaper disc, leaving the sponge backing pad in place.

3. Carefully center the new sandpaper disc and press into place. It will be held securely by the

hook and loop backing.

For excellent ﬁnish, we recommend the German made range of Intex Useit® Super Pads.

TO REPLACE CUSHIONED INTERFACE PAD

The sponge pad must be perfectly ﬂat to get good sanding results. If it is deformed or damaged it will

cause very uneven sanding. Always replace it when damaged. It is hook and loop on both sides, so to

Replace it, peel it away from the hook and loop on the Sanding Plate Base and afﬁx a new one.

BRUSH BRISTLES ON THE EDGE OF THE SANDING PLATE COVER

The brush bristles on the edge of the Sanding Plate Cover serve two purposes, they keep the sanding disc

properly aligned with the work surface without gouging and they also help the efﬁciency of the dust

collection by the vacuum cleaner. These brush bristles will wear with continued use. The Sanding

Plate Cover should be replaced when the bristles are too worn to ensure effective dust collection and

stabilization of the sanding head.

TO REPLACE SANDING PLATE COVER

1. Hold the sanding plate in one hand and with the other, using the L-hex wrench

(supplied), ﬁrst break free the center bolt clockwise (1/8 turn only!). Then only use

the L-hex wrench to hold the center bolt from turning and spin off the sanding plate

counterclockwise.

Super Pads

Jost®

Dustless Sander

Dust Extractors

8Intex Giraffe® intexinternational.com

ON & OFF Switch

FUNCTIONAL DESCRIPTION

2. Then, press the cover down against the spring and, using snap-ring pliers, remove

the circlip which holds the sanding plate cover to the bracket.

3. Finally, carefully work the vacuum hose free then lift sanding plate cover away.

Replacement is the opposite of removal. Don’t forget the spring. Entrust all

repairs to an Authorised Service Center.

TO INSTALL THE VACUUM CLEANER HOSE

1. Unplug the machine.

2. Plug the vacuum cleaner hose bayonet mount into the swivel mount in the back

of the machine. Once the tangs of the bayonet mount are fully inserted in the

slots, hold the swivel mount from turning and turn the hose bayonet mount

clockwise to lock.

3. Removal is the opposite of assembly.

THE VACUUM CLEANER

Ensure that you have a bag installed in your vacuum cleaner which is approved and rated

for drywall dust.

WARNING: Failure to use an approved dust bag in your vacuum will increase the level of airborne

dust in the work area. Prolonged exposure to such dust may cause respiratory harm.

For superior dust extraction, we recommend the german made range of Intex starmix®

dust extractors/vacuums.

STARTING AND STOPPING TOOL

Make sure that the power circuit voltage is the same as that shown on the speciﬁcation plate of the

machine and that switch is “OFF” before connecting the tool to the power circuit.

To switch on:

While holding with the left hand on the column and the right hand on the main handle,

Press the rocker switch to the “on” position. Anticipate and be ready for the start up

torque when the machine ﬁrst starts.

To switch off:

Press the rocker switch to the”off” position. After the machine has been switched

off, the sanding disc will still rotate for a time. Take care that parts of your body do

not come into contact with the disc and do not set the machine down while it is still

rotating!

Super Pads

Jost®

Dustless Sander

Dust Extractors

WARNING: To reduce the risk of injury, user must read and understand operator’s manual.

Position A Position B

IMPORTANT NOTICE!

THE HEAD POSITION B IS FOR SANDING WALLS & ALSO FOR STORAGE;

CHANGE THE HEAD SETTING TO POSITION A FOR CEILINGS ONLY.

Using or storing in the incorrect setting, will cause damage to the Drive Shaft & therefore void warranty.

Speed Adjustment

Head Locking

Catches

ADJUSTING THE ROTATION SPEED

The speed of the machine is variable to suit different tasks. It can be adjusted from

650/min up to 1600/min by using the thumb wheel. turn in the counterclockwise

direction to increase the speed and in the clockwise direction to decrease the speed.

Generally, you should use the higher speed for fast stock removal and the lower speed

for more precise control.

Note: We recommend the rotation thumb wheel be set to high speed during

operation for sufﬁcient airﬂow to the motor.

POSITIONING THE SANDING HEAD

There are two positions for the Sanding Head:

Position A: For sanding ceilings only.

Position B: For sanding walls and also for storage.

The position for ceilings (position A in the diagram) has the pivot ﬁxed out at

the very end of the fork. The position for sanding walls and for storage (position B in

the diagram), has the pivot ﬁxed at the middle position of the fork. To adjust, simply

pull the 2 spring loaded catches outwards, slide the pivot to the new position and

allow the catches to snap into place.

HOW TO USE THE TOOL

Effective control of this powerful saw requires two-handed operation for maximum safety and control.

The proper hold is to keep one hand on the main handle and the other hand on the sponge grip on the

column. It is vitally important to keep stable footing at all times, especially when standing on scaffolding

or stilts.

SANDING OPERATIONS

1. Once the machine and vacuum cleaner are set up and all safety measures and equipment are in

place, begin by turning on the vacuum cleaner and then the machine. (If you are using a vacuum

cleaner with integrated switching, then simply turn the machine on).

10 Intex Giraffe® intexinternational.com

Super Pads

Jost®

Dustless Sander

Dust Extractors

FUNCTIONAL DESCRIPTION

2. Begin sanding and carefully contact the work surface as lightly as possible-just enough to keep the

sanding head ﬂat against the surface.

Note: Excessive pressure applied to the sanding surface may result in strain and possible

drive shaft breakage. This may void warranty.

3. The joints in the sanding head allow the sanding disc to follow the contours of the work surface.

4. The best technique is to use overlapping sweeps and keep the head in constant motion. Never stop

too long in any one place or there will be swirl marks. With experience it will be very easy to create

excellent results.

Note: Ensure that the Super Pad abrasive you are using is suited to the task. Overly coarse grit paper

may remove material too quickly to control. While overly ﬁne grit paper may clog too often and

not shape down the surface. For more information on grits types visit intex.com.au

For excellent ﬁnish, we recommend the German made range of Intex Useit® Super Pads.

CAUTION: Take care to avoid pointed projections and nails, etc. This will wipe out the sandpaper

and probably damage the sponge pad as well.

MOUNTING THE OPTIONAL BAIL HANDLE

1. Loosen 2 Thumb Screws (05) and remove Clamp Cap (04).

2. Place handle in the desired position on the shaft.

3. Clamp handle in place by replacing the Clamp Cap and tightening

the Thumb Screws.

MAINTENANCE

Every 50 hours of operation blow compressed air through the motor while running at no

load to clean out accumulated dust. (If operating in especially dusty conditions,

perform this operation more often).

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with

a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise

damage the material. Wear safety glasses while using compressed air. Clean the vacuum swivel

connector as too much dust will keep it from turning freely.

THE CARBON BRUSHES

The Carbon Brushes are a normal wearing part and must be replaced when they reach their wear limit.

The Intex Power Sanders are ﬁtted with an auto-stop Carbon Brush, this mechanism will stop the Motor

when the brush reaches its wear limit, preventing damage to the Armature.

NOTE: Checking and replacing the carbon brushes should be entrusted to a Authorised Service

Center.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Intex Levigatrice

Intex

Intex AG700 Intex Giraffe Manuale utente

Manuali Levigatrice popolari di altre marche

Oliver

Oliver 6305 Manuale utente

Jet

Jet 22-44 Pro-3 Manuale di servizio

Makita

Makita M9204 Manuale

Makita

Makita M9204 Manuale utente

Craftsman

Craftsman 351.215131 Manuale utente

Clarke

Clarke Woodworker CBS1-5B Manuale di istruzioni

Chicago Pneumatic

Chicago Pneumatic CP9778 Manuale utente

Nitto Kohki

Nitto Kohki BB-20 Manuale utente

Ferm

Ferm FEOS-135 Manuale utente

Unior

Unior 1510 Manuale utente

stayer

stayer ls1200 Manuale utente

Jet

Jet JSG-96 Manuale di servizio

Parkside

Parkside PDS 290 B2 Manuale utente

Status

Status XPA Series Manuale utente

Clarke

Clarke EZ Sand Manuale utente

Craftsman

Craftsman 113.22521 Manuale utente

Craftsman

Craftsman 113.225831 Manuale utente

CLAS

CLAS OP 1429 Manuale utente