IOptron IPolar Manuale utente

Replacing a iPolar with a Optical Polar Scope

Tool needed: a set of metric hex key wrench and a small

Phillips screwdriver

1. Loosen two screws at the front of the mount and

two others on the top of a SkyGuider Pro main

board cover and remove the black cover.

2. Unplug the 6-wire motor driver cable and DC power

cable. Remember how wires wrapped.

3. Remove two mounting screws.

4. Gently pull the circuit board with sockets end up

and slide the circuit board out. If the board is stuck

by the motor, loosen two Phillips screws hold the

motor.

5. Remove polar scope base plate.

6. Rotate the RA axis to find TWO set screws which are

used to secure the iPolar in place. Use a 1.5mm hex

key to release the set screws. Pull the iPolar out of

the RA axle.

7. Insert optical polar scope into the RA axis. Rotate

the front camera mounting adapter to desired

orientation and adjust the polar scope so that the

LED illuminating hole is facing upward.

8. Lock polar scope via these 2 set screws.

Wire wrapping

9. Install the polar scope LED abr. Make sure the cable

plug is placed on the left side as shown.

10. Connect the polar scope LED cable between the LED

bar and the control board.

11. Sliding the front end of the control board in. Make

sure the LED cable underneath is not jammed.

12. Gently push the board in when the power cable

goes through the small cut on the board.

13. If you release the motor to gain more space while

remove the board, tighten motor locking screws

while push the motor against worm assembly to

tension the belt properly.

14. When securing the board with two screws, make

sure that the battery and wires underneath are

properly seated. Fully tighten the screws.

15. Plug in the battery wire and motor cable. Refer to

step 2 to wrap the wire properly. Put the cover and

screws on.

16. Replace the polar scope base plate.

Altri manuali per iPolar

3

Altri manuali iOptron Accessori

iOptron

iOptron iPolar Manuale utente

iOptron

iOptron MiniTower-II Manuale utente

iOptron

iOptron SmartStar Manuale utente

iOptron

iOptron iPolar 3339R-SGP Manuale utente

iOptron

iOptron HEM15 Manuale utente

iOptron

iOptron SmartStar iEQ45 Manuale utente

iOptron

iOptron iPolar Manuale utente

iOptron

iOptron CEM70 Manuale utente

iOptron

iOptron SmartEQ Pro+ Manuale utente

iOptron

iOptron PoleMaster 3338-25? PoleMaster 3338-34? PoleMaster... Manuale utente

iOptron

iOptron CEM26 Manuale utente

iOptron

iOptron CEM26 Manuale utente

iOptron

iOptron SmartStar CubePro Manuale utente

iOptron

iOptron iEQ45 Pro Manuale utente

iOptron

iOptron HAE69 Manuale utente

iOptron

iOptron SkyGuider Manuale utente

iOptron

iOptron CEM70 Manuale utente

iOptron

iOptron SkyHunter Portable EQ GOTO System Manuale utente

iOptron

iOptron SmartEQ Pro Plus Manuale utente

iOptron

iOptron CEM60 Manuale utente

iOptron

iOptron SmartEQ Manuale utente

iOptron

iOptron SmartStar Cube E Series Manuale utente

iOptron

iOptron SmartStar iEQ45 Manuale utente

iOptron

iOptron SmartStar iEQ45 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente