ioSafe 1513+ Manuale utente
ioSafe 1513+ Quick Start Guide
Powered by Synology DSM
910-11568-00 Rev03 QUICKSTART GUIDE, NC, 1513+, ENG
2
Table of Contents
Chapter 1: Before You Start
Package Contents...............................................................................................................................................3
ioSafe at a Glance...............................................................................................................................................4
Safety Instructions...............................................................................................................................................5
Chapter 2: Hardware Setup
Tools and Parts for Hard Disk Installation...........................................................................................................6
Install Hard Disks................................................................................................................................................6
Add a RAM Module on your ioSafe...................................................................................................................10
Replace System Fan Assembly ........................................................................................................................12
Chapter 3: Initial Start Up and Synology DiskStation Manager Install
Start Up Your ioSafe.........................................................................................................................................13
Install DSM with Web Assistant.........................................................................................................................13
Chapter 4: Product Support
Data Recovery Proceedure...............................................................................................................................15
Contact Us ........................................................................................................................................................15
Appendix A: Specifications
Appendix B: LED Indication Table
3
Chapter 1: Before You Start
Before you start setting up the ioSafe, please check the package contents to verify that you have received the
items below. Please also read the safety instructions carefully before use to prevent your ioSafe from any
damages.
Package Contents
Main unit x 1
AC power cord x 1
RJ-45 LAN cable x 2
Screws for 3.5” hard drives x 24
3mm Hex Tool x1
Magnet x1
4
ioSafe at a Glance
No.
Article Name
Location
Description
1) Power Button Front Panel The power button is used to turn your ioSafe on or off.
To turn off your ioSafe, press the Power Button and hold it until you hear a beep
sound and the Power LED starts blinking.
2) LED Indicators Front Panel The LED indicator is used to display the status of the internal disk and the
system. For more information, see "Appendix A: LED Indication Table" on Page
18.
3) USB 2.0 Ports Back Panel The ioSafe offers USB ports for adding additional external hard drives, USB
printers, or other USB devices.
4) USB 3.0 Ports
5) eSATA 1 Back Panel The eSATA ports are used to connect external SATA disks or Expansion Units1
to the ioSafe.
6) eSATA 2
7) RESET Button Back Panel 1.To restore IP, DNS, passwords for the admin account to default value.
2.To reinstall the ioSafe.
8) LAN Ports Back Panel The LAN ports are where you connect RJ-45 cable to the ioSafe.
9) Power Port Back Panel The power port is where you connect the power cord to the ioSafe.
10) Fans Back Panel The fans are built to exhaust waste heat. It will start automatically when the
server starts. If the fan is malfunctioning, the system will beep every few
seconds.
-----
1For more information about ioSafe Expansion Unit supported by your DiskStation, please visit www.iosafe.com .
5
Safety Instructions
Before cleaning, unplug the power cord first. Wipe ioSafe product with damp paper towels.
Do not place the ioSafe
product on a cart, table, or desk, which is not stable to avoid the product
from falling over.
The power cord must plug in to the right
supply voltage. Make sure that the supplied AC voltage
is correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.
Risk of explosion if battery
is replaced with an incorrect type. Dispose of used batteries
appropriately.
3-2-1 At ioSafe, we suggest a minimum of the "3-2-
1 Rule" for backup: Make 3 complete copies of your
data, keep them on at least 2 separate systems, and have at least 1 protecte
d from natural
disaster.
6
Chapter 2: Hardware Setup
Tools and Parts for Hard Disk Installation
A Phillips screwdriver
3mm Hex Tool (included)
At least one 3.5" or 2.5" SATA hard disk
(Please visit www.iosafe.com/support for compatible hard disk models.)
Warning: If you install a hard disk that contains data, the system will format the hard disk and erase all data. If you
need the data in the future, please back it up before installation.
Install Hard Disks
Note: If you purchased your ioSafe preloaded with Hard Disks you can proceed to the next section: Initial Start Up
and Synology DiskStation Manager Install.
1 Remove the Front Cover using the included 3mm Hex Tool
7
2 Remove the Waterproof Drive Cover using the 3mm Hex Tool.
3 Remove the Drive trays using the provided 3mm Hex Tool.
8
4 Install a compatible Hard Drive into each Drive Tray using (4x) Drive Screws and a Phillips screwdriver.
(Please visit www.iosafe.com/support for compatible hard drives models.)
Note: If you want to set up a RAID set, it is recommended that all installed hard disks are of the same size to make
the best use of hard disk capacity.
5 Insert the loaded hard drive tray into the empty hard drive bay and tighten the screws using the 3mm Hex Tool.
Important: Make sure the tray is pushed in all the way. Otherwise, the hard disk might not function properly.
9
6 Replace the Waterproof Drive Cover and securely tighten using the supplied 3mm Hex Tool
WARNING: BE SURE TO TIGHTEN THIS SCREW USING THE PROVIDED HEX TOOL. THE HEX TOOL IS
DESIGNED TO FLEX SLIGHTLY WHEN THE SCREW IS SUFFICIENTLY TIGHT AND THE WATERPROOF
GASKET IS PROPERLY COMPRESSED. AVOID USING TOOLS OTHER THAN THE SUPPLIED HEX TOOL AS
YOU COULD UNDER TIGHTEN OR BREAK THE SCREW.
7 Install the Front Cover to finish the installation and protect the drives from fire. Keep the Hex Tool nearby for
future use. A magnet is provided to attach the Hex Tool to the back of the ioSafe or some other convenient
location.
10
Add a RAM Module on your ioSafe
The optional RAM module 2GB (DDR3) is designed for your ioSafe 1513 memory expansion. Follow the steps
below to install, check, or remove a RAM module on your ioSafe.
To install the RAM module:
1 Shut down your ioSafe. Disconnect all cables connected to your ioSafe to prevent possible damage.
2 Remove the 2 screws that secure the bottom access panel.
Important: When you remove the access panel, you expose sensitive internal components. Avoid touching
anything other than the memory assembly when you remove or add memory.
3 Insert the new memory module in the slot:
a Align the notch on the gold edge of the module with the notch in the lower memory slot.
b Tilt the card and push the memory into the slot. Make sure the module is pushed in all the way.
Use two fingers with firm, even pressure to push down on the memory module. You should hear a click when the
memory is inserted correctly.
Important: Hold the memory module by its edges, and do not touch the gold connectors.
Indice
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
