Iron logic Matrix 2 EH Manuale utente
Operating Manual
Reader is mounted on a flat surface at the place, where PROXIMITY card can be brought to
it without obstructions. Complete following operations for “MATRIX-II”EH reader mounting:
1. Mark up and drill holes for fastening corresponding to the reader's holes size (fig. 1.).
2. Connect cables to the reader's slot, according to the scheme.
3. Depending on the direction of mounting of the reader's connection cable remove the thin
strap in the reader case and install a cable into it.
When the power is applied to the reader the red LED is lighted.
4. Mount the reader and fasten it with screws.Cover the holes in the reader with plugs from
the set.
" " ltd.Iron Logic
RUSSIA: “Iron Logic” ltd., 7, street, Russia, 195009
RUSSIA: “Iron Logic” ltd., , 2, av. Russia, 105122
High Street, Bromley, Kent, BR1 1PQ, London, UK, Tel: +44 (0) 208 460 2880; Mobile: +44(0) 780 385 3449
Bobrujskaja Saint-Petersburg, , phone/fax (812) 703-77-65, 542-11-85, 542-04-80
office 214 Stchelkovskoje , Moscow, , phone/fax (495) 367-93-40, phone for communication from Moscow to Saint-Petersburg (495) 78-77-066
UK: "RF ENABLED ID" ltd., Northumberland House, Aldbridge Suite, 230
Technical support web site:
E-mail:
http:// con.ru
@con.ru
www.
marketing
www. .rucon
Matrix 2 EH
Proximity card reader
Reader “MATRIX-II”EH is used in access control systems as a reader for non-contact cards of PROXIMITY type, EM-Marine and HID standard, and for conversion of read card
code into Dallas Touch Memory code and Wiegand 26. Rader enables simultaneous usage of cards of two standards, EM-Marine and HID, in access control systems.
GENERAL INFORMATION
CHARACTERISTICS
READER OPERATION
CONNECTION SCHEME
DELIVERY SET
Identifiers: cards of EM-Marine and HID standards
Automatic identification of card standard without additional setting.
Card/keychain reading distance:6-14 cm
Output protocol:Dallas Touch Memory, Wiegand 26
Distance from reader to controller in Dallas Touch Memory mode – up to 15 m.
Distance from reader to controller in Wiegand mode – up to 100 m.
Card reading confirmation: buzzer signal, two-color LED
Indication: internal and from external control
Supply voltage:8-18 VDC
Current consumption in a standby mode:35 mA
Operating temperature:-40°C up to +50°C
Relative humidity, not greater:95%
Dimensions (mm):85x44x18 mm
Reader operation without external indication control (internal indication):
1. When there is no card in the reader's action field, red LED is always on.
2. At the moment the card is brought to the reader's action field red LED
turns off, green LED blinks and short sound is produced.
3. While the card is in the reader's action field there is no light indication.
External control of red and green LEDS and sound is performed by closing
on the common terminal. External indication can be used with internal one,
i.e. external control excludes only the channel, where external control is
detected.
“MATRIX-II'EH reader1 pc
Plug 2 pcs
Screw 3x302 pcs
Dowel2 pcs
Operating manual1 pc
Connection for Wiegand 26 and lbutton
Reader's terminals Controller's terminals
Dallas (TM emulation)
Wiegand 26
Dallas (single transfer)
DATE 0
DATE 1
DATE 0
DATE 1
DATE 0
DATE 1
DATE 0
DATE 1
TM (central)
Common (-)
TM (central)
TM (central)
MOUNTING AND CONNECTION
Plugs
LED
Places
for cable
grooming
Remove the sticker to increase
the volume of buzzer
Slot terminals:
1. power supply +12V
2. common (Minus)
3. output DATA 0
4. output DATA 1
5. LED-G (external green control)
6. LED-R (external red control)
7. BEEP (external sound control)
Fig. 1
Altri manuali Iron logic Lettore di schede
