Ironclad HIL885 Guida rapida

ADJUSTABLE BASKETBALL SYSTEM

MODEL: HIL885

ASSEMBLY INSTRUCTIONS AND OWNER'S MANUAL

WARNING

IRONCLAD SPORTS, INC

902 Corey Road, Hutchinson, KS 67501

Telephone: 620-662-2233

www.ironcladsports.com

IRONCLAD SPORTS , INC

HIGHLIGHT HOOPS

Keep this instruction manual in case you have to contact the manufacturer for replacement parts.

FAILURE TO COMPLY WITH ANY OF

THE WARNINGS IN THESE INSTRUCTIONS

MAY RESULT IN SERIOUS PERSONAL

INJURY.

FAILURE TO COMPLY MAY ALSO

RESULT IN PROPERTY DAMAGE.

PLEASE HEED ALL WARNINGS AND

CAUTIONS TO ENSURE YOUR SAFETY.

DO NOT ATTEMPT TO ASSEMBLE

THIS SYSTEM WITHOUT CAREFULLY

READING AND FOLLOWING ALL

INSTRUCTIONS. BEGIN BY IDENTIFYING

AND TAKING INVENTORY OF ALL PARTS

USING THE PARTS LIST PROVIDED.

TOOLS AND MATERIALS REQUIRED FOR ASSEMBLY

(Not Included)

1. 2 Adjustable Wrenches 10. Concrete-1/2 yard or 14-16

2. Socket Set Bags, (80 lb. bags)

3. 9/16" Wrench 11. Phillips Head Screwdriver

4. 3/4" Wrench

5. 15/16" Wrench 13. Carpenter's Level

6. ½" Wrench 14. Water Supply

7. Hammer or Mallet

8. Tape Measure

9. Shovel

**A MINIMUM OF SIX ADULTS IS

REQUIRED TO LIFT UNIT INTO PLACE**

STOP! STOP!

BEFORE YOU START

A. Identify and inventory all parts using the checklist boxes in the parts list. Be sure to

keep the hardware bags and their contents separate. If any parts are missing call

our Customer Service Department ( ).620-662-2233

B. Test fit all Bolts by inserting them into the respective hole. If necessary, carefully

scrape away any excess powder coating buildup from inside the holes. Do not

scrape away all of the powder coating. Bare metal may rust.

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE

AND WILL VOID THE WARRANTY. The owner must ensure that all players know and follow these rules to safely operate the

system. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk

of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, or operated

properly.

● ●If using a ladder during assembly, use extreme caution. Follow all warnings and cautions on the ladder carefully. 6

people are required to lift the unit into place. Before digging, contact the appropriate agency to locate underground

●

power cables, gas, and water lines. Do not install the system within 20 feet of overhead power lines. Climate, corrosion,●

or misuse could result in system failure. If technical assistance is required, contact the manufacturer. Minimum● ●

operational height is 7'6 to the Rim. Most injuries are caused by misuse and /or failure to follow instructions.”

Use caution when using the system.

12. A minimum of 2 Ladders

Verify all parts listed on packing list are present prior to installation. Contact our Customer

Service at 620-662-2233 for assistance with replacement of any parts missing or damaged.

ITEM QTY DESCRIPTION

A 1 8"x8"Main Post

B 1 Main Extension Arm

C 1 Small Extension Arm

D 1 Extension Arm Plate

E 1 Backboard with frame

F1Rim

G 1 Rim spacer (plastic & steel)

U1 1 Anchor Template

U2 6 18mm Anchor J-bolts

U3 12 Thick washer for J-bolts

U4 18 Hex nut M18

U5 4 Anchor Rebar 36"L

U6 6 Lock Washer M18

R1 4 Carriage bolt M10x70

R2 4 Flat Washer M10

R3 4 Flange nut M10

ITEM QTY DESCRIPTION

1 6 Hex bolt M16x250mm

2 12 Flat Washer M16s

3 6 Lock nut M16

4 4 Hex Bolt M10x30mm

5 4 Lock washer M10

6 4 Flat washer M10

HARDWARE LIST

PARTS LIST

RIM HARDWARE

UNDERGROUND PARTS

R2 R3

Pre-installed

bolts & nuts on

backboard fra me

Pre-installed

bolts & nuts on

backboard fra me

a. Dig a hole 52" deep and 25"x 25"square . The edge of the hole

should be flush with the edge of the playing surface. If you live in an area

where heavy frost can occur, it may pose a problem, consult your local

building inspector to determine the appropriate hole depth.

b. Build a form before pouring the concrete pad, to ensure that the top

of the concrete remains straight and square. The form should

be placed about 1/2" above the playing surface to allow for water drainage.

c. Bell out the bottom of the hole.

25"

52"

NOTE: The hole must be at least 52" deep.

NOTE: A square hole prevents the rotation of the concrete.

NOTE: The area behind the playing surface must be cleared off by at least

3 feet to enable the user to stand behind the pole to adjust the Rim height.

NOTE: Before digging, call to locate any buried utility lines.

NOTE: At rim height 10 , distance from the face of backboard to the’

front of Main Post(A) is 60 , Choose the proper location to dig”

for the concrete footing:

STEP B

A. Thread a 18mm Hex Nut (U4) onto each of the 18mm J-Bolts

(U2).Securely tighten the Nuts all the way down to the end of the

threads.

B. Slide the threaded end of the J-Bolts through the holes

in the Anchor Template (U1) and secure each J-Bolt with a

18mm J-Bolt Hex Nuts(U4) as shown. Securely tighten all Nuts

at this time.

NOTE: Make sure the curved J ends of the J-Bolts are“”

oriented in a rectangular pattern, as shown.

STEP C

STEP D

a. Mix the concrete according to the instructions on the bags. Note that

a thicker mix of concrete will dry stronger than a thin mix. Pour the

concrete into the hole, stopping approximately 18 inches from the top

of the hole.

b. Insert the four pieces of Anchor Rebar (U5) into the hole, pushing each

piece firmly to the bottom of the hole. The four pieces should be

arranged in a square approximately 8 inches wide so that each piece of

rebar will be positioned next to the J-Bolts when the J-Bolt Template

is placed in the cement.

c. Finish filling the hole to the top with concrete. The top of the concrete

should reach just above the level of the top of the form.

a. Position the J-Bolt Template (U1) over the hole as shown.

with the sides of the plate square with the sides of the hole.

b.Push the J-Bolts (U2) into the concrete until the J-Bolt Template is

resting flat against the surface of the concrete.

c. Grasp the tops of the J-Bolts and agitate the Template assembly back

and forth repeatedly to eliminate any air bubbles in the concrete. Lift the

Template slightly above the concrete when agitating . Make sure the

Template is resting on the concrete after agitating. Form the concrete

into a downward slope away from the Pole to allow water runoff.

d. Clean off any concrete that may be on the J-Bolt Template or the exposed

portions of the J-Bolts.

e. Using a carpenter’

s level, make sure the Template is square to and level

with the playing surface.

f. Allow the concrete to cure for a minimum of 5-7 days before installing

the rest of your basketball system. In cold , wet weather or humid

climates, allow additional time for the concrete to cure.

YOU ARE NOW FINISHED WITH THE INITIAL ASSEMBLY STEPS. DO NOT PRO-

CEED WITH THE ASSEMBLY UNTIL THE CONCRETE HAS FULLY CURED . CUR-

ING WILL TAKE A MINIMUM OF 72 HOURS. IN HUMID CLIMATES OR WET

WEATHER, ALLOW ADDITIONAL TIME FOR THE CONCRETE TO CURE.

WARNING

NEVER USE THE SYSTEM WITHOUT FOLLOWING THE CEMENTING INSTRUCTIONS . FAILURE TO

FOLLOW ALL OF THESE INSTRUCTIONS AND WARNINGS COULD LEAD TO SERIOUS PERSONAL INJURY

OR PROPERTY DAMAGE AS LISTED ON PAGE ONE.

Playing surface

(Front side)

Anchor

template

Edge of

playing surface

This side faces

playing ground

! !

WARNING

*BECAUSE OF THE SIZE AND WEIGHT OF THE SYSTEM, A MINIMUM OF

THREE ADULTS ARE REQUIRED FOR THE FOLLOWING STEPS*

STEP1

A. Slide a 18mm Thick Washer (U3) over each of the J-Bolts(U2) as shown in FIGURE 1A.

B. Remove the Padding from Main Post (A). Place the Main Post (A) over the J-Bolts. Slide a 18mm

Thick Washer(U3), a Lock washer M18 (U6) and thread a 18mm Hex Nut (U4) to each J-bolt.

Tighten the Nuts only a few turns onto the J-Bolts as shown in FIGURE 1B.

C. If the Main Post (A) is not exactly vertical, adjust the 18mm J-Bolt Hex Nuts(U4) located under the

Post base. Tighten all of the Hex Nuts(U4) Above Post base when Main Post(A) is vertical.

STEP2

FIGURE 1A FIGURE 1B

Tight the Small Extension Arm (C) to Main Extension

Arm by using 4pcs M10 x 30mm Hex Bolts (#4), 4pcs

Flat Washer M10 (#6), 4pcs Lock Washer M10 (#5) .

Do not tighten at this time.

STEP 3

STEP 4

Position the Main Extension Arm (B) to the Line on Main post (A) as shown in Figure 3A.

Connect Main Extension Arm (B) to Main Post (A) with one Extension Arm Plate (D), using 6 Hex Bolts

M16x250mm (1), 12 Flat Washer M16 (#2), 6 Lock nuts (#3). See Figure 3B.

FIGURE 3A

10FT line

FIGURE 3B

Line up the top edge of

Main Extension Arm

plate with 10FT line on

Main Post.

Remove the nuts and washers from pre-

installed bolts on backboard frame.

Connect Backboard frame to Extension Arm

Assembly (B&C) using removed nuts and

washers.

1223

Remove the nuts and

washers from pre-

installed bolts on

backboard frame

Attach backboard frame

to Main Extension arm

using removed nuts and

washers.

Attach backboard frame

to Small Extension arm

using removed nuts and

washers.

Backboard

Frame

STEP 5

A. Insert 4pcs Spacers (Plastic & steel ) (G) to the 4 holes in Backboard Glass.

B. Remove the screws on Rim spring box cover, open the Spring box.

(Rim Spring Box cover may not be factory-assembled.)

Slide 4 Carriage bolts M10x70mm (R1-rim hardware kit) thru Rim plate, Spacers and Backboard, secure

with 4 Flat washers M10 (R2-Rim hardware kit ) and 4 Flange nuts M10 (R3-Rim hardware kit ) from the

backside of Backboard.

Re-attach Spring box cover to the Rim with

removed screws.

NOTE: Use a level to make sure rim is level side

to side before tightening nuts.

Indice

Altri manuali Ironclad Accessori

Ironclad

Ironclad GC55-LG Guida rapida

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente