ISANTA SENCO SIDDM302 Manuale utente
KYOCERA SENCO Netherlands B.V.
Pascallaan 88
8218 NJ Lelystad, The Netherlands
+31 320 295 575
senco.com
EMEA: senco.eu
© 2020 by KYOCERA SENCO Netherlands B.V.
Operating Instructions
(Original Instructions)
NFE2DT1032020
Diamond Core Drill
SIDDM302
2
Read the operating instructions before use.
Only for EU countries
Disposal of electric tools together with household waste is not permissible!
In observance of European Directive on waste electrical and electronic equipment and its implementation in accordance
with national law, electric tools that have reached the end of their life must be collected separately and returned to an
environmentally compatible recycling facility.
MEANING OF SIGNAL WARDS WARNING & CAUTION
The instruction manual includes two signal words: WARNING & CAUTION which are meant as follows.
WARNING : It is assumed that if the user uses the machine wrongly, it would be the risks
that the user could be died or injured.
CAUTION : It is assumed that if the user uses the machine wrongly, it would be the risks
that the user could remain the disabled or damage for the materials.
“CAUTION” might cause the serious accidents depending on the situations. Since we mention
the important notices, please strictly follow the instruction in order to avoid the accidents.
“Diamond core drill” is described as “Core Drill” in context.
“Diamond core bit” is described as “Core Bit” in context.
3
1.WARNING AND CAUTION 4
【1】Safety Notice for Electric Tools 4
【2】Notes for Usage of Core Drill 6
【3】For Mounting Drill Carriage Assy. and Pole Base 8
2.DESCRIPTION 9
3.SPECIFICATIONS 10
4.STANDARD ACCESSORIES 10
5.APPLICATIONS 10
6.GENERAL DRAWING AND SPECIFICATIONS IN OPERATION 11
7.OPERATIONAL INSTRUCTIONS
【1】Anchoring Core Drill 12
【2】Anchoring Core Drill by Anchor Bolt 12
8.MAINTENANCE AND SERVICING
【1】Maintenance 14
【2】Regular Servicing 14
9.FOR REPAIRING 17
10.INFORMATION ON NOISE EMISSIONS 17
11.WARRANTY 17
12.CE DECLARATION OF CONFORMITY 18
4
1. WARNING AND CAUTION
● To avoid the risk of re, electric shock and personally injury, follow all the instruction
mentioned in “Safety Notice for Electric Tools” and “Notes for Usage of Core Drill”.
●Before using, please read “WARNING & CAUTION”, and follow the instructions for your safety.
●After reading, keep the manual in that anyone can utilize as for the reference.
【1】Safety Notice for Electric Tools
WARNING
1. Do not use for other than specied purposes.
2. No one allow to get close to the working area except the workers.
●No one allow to contact to the electric tools and cord except the workers.
3. Avoid dangerous environments.
●Do not use the electric tools in the rain, moisten and wet place.
●Keep working area lightly.
● Do not use the machine where there are ammable gas or ammable liquid.
●Cluttered work areas invite accidents.
4. Wear appropriate work clothes.
●Do not wear the loose clothing or jewelries in order to avoid to being caught in the rotating parts.
●Wear rubber gloves and slip stopper footwear.
●Wear cap or hair cover in case that you have long hair.
5. Wear ear protector such as earplug or ear muffs.
●Wear ear protector in the place of noise.
6. Wear safety glasses.
●Wear safety glasses during working. If there is dust, please wear the dust mask.
7. Do not work with improperly posture.
●Fix the footing and maintain the balance at all times.
8. Work carefully without staying alert.
●When using the electric tools, please operate carefully by considering operation methods, how to use and
surrounding area.
●Do not come close to the rotating parts. It will be dangerous to being caught in or injured.
●Be careful for not to tuck the hands and the foots into the moving parts or connecting parts.
●Do not use machine when you are tired or distracted.
9. Be careful for receiving electric shocks.
●During operation, be careful for not to contact your body to the objects which are grounded such as micro-
wave and refrigerator and so on.
●Use power source equipped with earth leakage breaker.
10. Do not treat the cords and the hoses roughly.
●Do not carry the electric tool by holding the cord.
●Do not remove the machines by pulling the cord from the power receptacle.
●Do not get close the cord near the heat, oil and sharp objects.
5
WARNING
11. Use SENCO recommended accessories and options.
●In case that you use the accessories and the options which are not listed in the manual, it might cause the
accidents or personal injury. Please do not use the accessories and the options which SENCO does not
recommend.
12. Inspect for the damaged parts.
●Before using, please inspect the protection cover and other parts damages carefully, and make sure that
whether the machine operate properly and the designed functions work or not.
●Check for alignment, binding of moving parts, parts damages, mounting, and any other conditions that may
affect operation.
●Regarding the exchange or the repair for the damaged parts, please follow the instruction.
●In case that there are no instructions in the manual, please contact to the distributors or KYOCERA SENCO Nether-
lands B.V.
●Do not use the electric tool if the switch cannot be turned on or off.
●If the switch is broken, please contact to the local distributors or KYOCERA SENCO Netherlands B.V. for re-
pairing.
13. Turn the electric tool off and remove the plug from the power supply as following cases.
●In case that the machines is not used or repaired.
●When exchanging the options such as blade or Core Bits.
●In case that you can anticipate other hazardous situations.
14. Remove the key or the wrench for sure.
●Before turning on the switch, please make sure that the key and the wrench which are used for the inspec-
tion and adjusting are removed.
15. The electric machines are maintained carefully.
●Regarding exchanging the options, please follow the instruction.
●Keep the grip dry and clean, and avoid the oil or grease.
●Inspect the cord regularly. In case that there are damages, please contact to the distributors or KYOCERA
SENCO Netherlands B.V. for repairing.
●In case that you use the extended cord, inspect it regularly. If there are damages, please replace it.
16. In case that you do not use the tools, please store it appropriately.
●Store the place where keep children away, locking is available and dried place.
17. Avoid accidental starting.
●Do not carry the tools with connecting to the power supply.
●Before plugging the plug into the power supply, please make sure that the switch is off.
18. Use an appropriate extension cord for outdoors.
●In case that you use it in outdoors, please use the extension cord of cab tire cord or cab tire cable.
19. Use the appropriate tools according to your work.
●Do not use the small electric tools and accessories for the work which is done by using the large electric
tools.
20. Contact KYOCERA SENCO Netherlands B.V. sales (service) representative for repairing of the electric
tools.
●The machine is manufactured in compliance with applicable safety standards.
Do not remodel machine and tool.
●In case that the unauthorized person repairs it, it might cause the machine failure, accident or personal injury.
●Contact to KYOCERA SENCO Netherlands B.V. sales (service) representative for repairing.
6
【2】Notes for Usage of Core Drill
(In case of combination with original SENCO Drill Carriage Assy. and Pole Base.)
WARNING
1. Check for the embedded conduit etc.
●In case that you contact to the electric wire or conduit in that there are electric current, you may receive the
electric shocks.
● Before drilling the wall or the oor, check for the embedded conduit etc adequately.
2. Be sure to wear the rubber gloves and the rubber shoes.
●Since this machine uses the water, be sure to wear the rubber gloves and the rubber shoes.
3. Do not use for the ceiling plane.
● Since the Core Drill is used the water, it is extremely dangerous to drill for the ceiling plane due to owing
the water into the inside of motor.
4. Regarding the operation of high-place work, please follow the applicable laws and regulations .
●Secure the safe scaffold, and do not operate the machine 1.5m higher than the scaffold.
●In case that you work at high place, secure the enough scaffold space and secured scaffold.
●In case that you work at high place, keep any person away under your working area.
5. Be careful for the safety of the penetration side.
●When drilling for the penetration, cutting Core Bit might fall out or the cutting water might be leaked. There-
fore, please do the safeguard and the drain water handling in order not to avoid to hit the human beings
or objects. Then, please start operating.
6. Use the proper voltage which is indicated on the nameplate.
●In case that you apply for the voltage which is over the indicated voltage, it will cause the accidents.
7. Fix the Pole Base properly.
● It is extremely important to x the Pole Base securely. If it is not xed securely, the Core Bit might be dam-
aged by rattling of Core Drill or jammed.
8. Use the Water Collector for sure.
● Use Water Collector pad for sure in order to avoid the water owing into the inside of motor by ying apart
the water during operation.
●When using Water Collector, please install it adequately in order not to leak the water.
9. Do not contact to the rotating Core Bit and Main Shaft.
●Do not contact your hands and body to the rotating Core Bit and Main Shaft. It might be caught in or in-
jured.
10. Do not block the air hole of motor, and do not put the materials into the air hole.
11. Turn the switch off immediately if any abnormality is found.
●When the Core Bit stops or you hear the strange noise during the operation, please turn switch off immedi-
ately.
12. In case that you use Vacuum Pad for xing the Pole Base, please do not use the Automatic Feeding Sys-
tem.
●The Pole Base comes up, and it is extremely dangerous.
13. Asbestos is the harmful to human beings. In case that you drill containing such materials, please follow
the applicable laws and regulations, and take a measure for dust control.
14. Do not use the Core Bit which has a outshoot.
●If the rotating objects has a outshoot, it might be the risk for being caught in or injured.
7
WARNING
15. Do not use the Core Bit which exceeds the maximum diameter of Core Bit.
16. Connection for water supply must be ensured.
●Water might be splashed to the electric tool or person in working area.
17. In case that Pole Base is xed, ensure to x it at stable place.
18. If accessories are broken, don’t use it. Repair or replace.
19. Check the Core Bit, Tube and Coupling with no crack, tipping or deformation by visual conr-
mation. In addition, check the excessive wearing at edge of Core Bit or part of shank. If there is
any abnormal things, never use Core Bit.
20. If the cutting performance becomes lower, do dressing. If you use lower performance Core Bit,
it becomes high temperature and break, then there is possibility to get injured.
●Drill to rough grind stone or soft cutting material. (Concrete block, brick, or grind stone)
21. Be sure to switch off Core Drill before pressing Green on Button of PRCD.
CAUTION
1. Do not overload with Core Drill.
● Use the machine according to the machine capacity of specications in order to use safely and ef-
ciently.
2. When drilling, please supply the water for sure.
●Overheating of Core Bit reduces not only drilling performance but also its life. So make sure to keep
supplying water during drilling operation.
●Use clean water only. Using the dirty water may cause machine failure.
3. Do not turn on the motor with Core Bit facing to the drilling surface.
●It causes the damages for Core Bit and Core Drill.
4. When starting the drilling, please wait until the rotating is increased.
●Regarding the drilling work, turn the switch on and wait until the rotating is increased fully.
5. Do not stop rotating of Core Bit by forcing the power on the Feeding Handle during drilling, and
do not lock the Core Bit.
●It might cause the damages for the Chip of Core Bit and Core Drill.
6. When releasing your hands from the Feeding Handle, please make sure that L bolt is tight-
en, then, x the Drill Head.
●When loosening L bolt, please hold the feeding handle in order not to move the Drill Head.
7. Before starting operation, test PRCD in the following procedures.
●Plug Power Cord and press Green on Button. Make certain Red Lamp is on.
●Press Blue TEST Button and make certain Red Lamp is off.
●Press Green on Button again and make certain Red Lamp is on.
8
【3】For Mounting Drill Motor on Drill Carriage Assy. and Pole Base
WARNING
1. This Drill Motor is designed to be combined with Drill Carriage Assy. and Pole Base designed
for Core Drill. Use Drill Motor in one of the following ways.
●To combine with a genuine SENCO brand Drill Carriage Assy. and Pole Base.
●After combining with Drill Carriage and Pole Base, the distributor must make a CE marking and issue
CE DECLARATION OF CONFORMITY.
2. Drill Carriage Assy. and Pole Base which are mounted on Drill Motor must have capacity of
specied Max. drilling diameter or larger capacity.
●If combined with Drill Carriage Assy. and Pole Base which have lesser capacity, Drill Motor cannot
function fully and this could lead to accidents and injuries.
3. Combine Drill Motor with Drill Carriage Assy. securely.
●Attach Key always.
● Properly x them by using 4pcs of attaching bolts.
9
Unied screw (1-1/4”-7 UNC)
(The outside of Main Shaft )
Motor
Hose Band 00
(Standard Accessories)
G 1/2 (The inside of Main Shaft)
Plug
Carbon Cap
Hose 12×250
(Standard Accessories)
PRCD
(Cord 2.4m)
Speed Change
Knob
Water Cock
Attaching Screw Hole M8 P1.25 Depth 23mm
Switch (Built-in Circuit Breaker)
25
60
10
145
110
132
179
457
Name Plate
2. DESCRIPTION
10
Model SIDDM302
Motor Single phase series commutator Motor
Power Supply Single-phase A.C. 230V 50Hz
Rated Current 8.7A
Power Consumption 1900W
Max. Output 2400W
No Load Speed 370/880min-1
Max. Bit Dia. 355mm 14”
Core Bit Installing Screw Outside Unied screw (1-1/4”-7UNC)
inside G 1/2
Drill Motor Weight (Excluding cord) 11.2kg
Max. Burst Pressure(Hose) 3.9MPa
4. STANDARD ACCESSORIES
●Hose Band 00 1
●Hose 12×250 1
●Water Cock 1/4” Gardena 1
●Instruction Manual 1
5. APPLICATIONS
This tool is Core Drill for drilling in concrete.
●Core Drilling in concrete for road, dam, tunnel and bridge construction.
●Sampling test pieces.
●Core Drilling of pilot hole for guard rail post and fence post.
●Core Drilling in concrete for wiring and plumbing for air conditioning, telephone, electricity, water and
gas supply.
3. SPECIFICATIONS
Indice
