ISHIDA Uni-3 Manuale utente
RS-61004-11 1.02
User’s Manual
Ver. 0.00
IMPORTANT
•Read this manual thoroughly, and do not perform installation,
operation, maintenance, or inspection unless you fully
understand all of the contents.
•Keep this manual in a safe place where you can refer to it
easily while installing, operating, and carrying out
maintenance or inspections.
Bench Type
Hanging Type
Pole Type
Elevated Type
© ISHIDA Co., Ltd. 2013 All rights are reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means
mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA.
Chapter 1: BEFORE USE
Uni-3 User’s Manual 1-1
BEFORE USE
1.1 SPECIFICATIONS
UNIT ITEM DESCRIPTIONS
Weighing unit Weighing capacity 15 kg specification: 0 to 6 kg / 2 g, 6 to 15 kg / 5 g
30 kg specification: 0 to 30 kg / 0.010kg
Weighting accuracy 1/3000
Operation panel unit Display method L1: 23-digit 16-segment LCD
L2: 192 X 16 dot matrix / 23-digit 7-segment LCD
Customer display unit
Display method L1: 23-digit 16-segment LCD
L2: 192 X 16 dot matrix / 23-digit 7-segment LCD
Printer unit Printing method Direct thermal method
Thermal head 2 inches (448 dots) and 8 dots/mm
Printing speed 100 mm/second
Note: The printing speed may vary depending on the label
conditions.
Printing effective size 56 mm in width
Label roll size Label width: 38 to 68 mm
Label length: 30 to 175 mm
Label roll size Roll outside diameter ϕ100 mm max.
Paper core inside diameter ϕ40 mm ±1 mm
Others Power supply 100 to 240 VAC, 50/60Hz
Use conditions Temperature: -5 to 40°C
Humidity: 20 to 85%, non-condensing.
Input / Output LAN: 1 channel
USB: 1 channel
RS-232C: 1 channel
1
Chapter 1: BEFORE USE
1-2 Uni-3 User’s Manual
1.2 PART NAMES
Bench Type
Chapter 1: BEFORE USE
Uni-3 User’s Manual 1-3
1.3 OPERATION PANEL
Keys for Usual Use
Used to delete an entered
numerical value.
Used to call Menu Select display.
Used to call a registered product
data.
Used to move the cursor or turn
pages.
Used to feed labels.
Used to move the cursor or turn
pages.
Used to issue a label.
Used to move the cursor or turn
pages.
Used to enter tare weight.
Used to move the cursor or turn
pages.
Used to reset a weigh to zero.
Used to escape from the current
mode.
Chapter 1: BEFORE USE
1-4 Uni-3 User’s Manual
1.4 LEVEL ADJUSTMENT
Install the machine horizontally to use.
Be sure to turn off the power switch before placing the machine on a stable platform, and adjust the machine
inclination by turning the four level adjustment legs so that the bubble is located at the center of the level gauge.
Accurate measurements cannot be performed if it is not installed horizontally.
Chapter 1: BEFORE USE
Uni-3 User’s Manual 1-5
1.5 LABEL / RECEIPT ROLL LOADING
1.
Open the cover at the side of the main body.
Ensure that nothing is placed on
the weighing platter.
2.
Set a new roll around the roll holder and raise the roll stopper to fix the roll position.
3.
Twist the lever as shown in the figures below to unlock the thermal head.
Chapter 1: BEFORE USE
1-6 Uni-3 User’s Manual
4.
Thread the paper as shown in the figures below.
5.
For labels, fix the paper end with the backing paper stopper, and gently turn the winding bobbin
clockwise until the label becomes tight.
6.
Push the lever to lock the thermal head.
Winding bobbin
Chapter 1: BEFORE USE
Uni-3 User’s Manual 1-7
7.
Press the [FEED] key to issue a label.
At this time, confirm that the label is completely peeled off.
Confirm that the backing paper is
wound up smoothly. If the backing
paper is wound up diagonally,
check that the label is set correctly.
Chapter 1: BEFORE USE
1-8 Uni-3 User’s Manual
1.6 REMOVING & REPLACING OF WEIGHING PLATTER
1.6.1 REMOVING THE WEIGHING PLATTER
When removing the weighing platter from the main body, lift the front side to pull out the two pins from the two
rubber platter holders and remove the platter by pulling it to disengage the two hooks at the rear side of the
platter.
1.6.2 REPLACING THE WEIGHING PLATTER
When replacing the weighing platter onto the main body, engage the two hooks at the rear side of the platter
and lower the platter so that the two pins on the bottom of the platter are inserted into holes of the rubber
platter holders.
Altri manuali per Uni-3
2
Indice
Altri manuali ISHIDA Scala
ISHIDA
ISHIDA IGB Series Manuale utente
ISHIDA
ISHIDA AC-2000 Manuale utente
ISHIDA
ISHIDA INS-100 Manuale utente
ISHIDA
ISHIDA IWQ Series Manuale utente
ISHIDA
ISHIDA BC-300 Manuale utente
ISHIDA
ISHIDA Uni-3 Manuale utente
ISHIDA
ISHIDA SR-2000 alpha Manuale utente
ISHIDA
ISHIDA IPC Manuale utente
ISHIDA
ISHIDA Astra Manuale di istruzioni
ISHIDA
ISHIDA AC-4000 Series Manuale utente
ISHIDA
ISHIDA IGX Series Manuale utente
ISHIDA
ISHIDA MTE-300 Manuale utente
ISHIDA
ISHIDA INS-100 Manuale utente
ISHIDA
ISHIDA Uni-5 Manuale utente
ISHIDA
ISHIDA CB-300 Electronic balance Manuale utente
ISHIDA
ISHIDA INS-100 9k Manuale utente
ISHIDA
ISHIDA UNI-7 Manuale utente
ISHIDA
ISHIDA IWQ-150 Manuale utente
ISHIDA
ISHIDA IPC-WP Manuale utente
ISHIDA
ISHIDA AC-3000 Manuale utente
