ISolutions DMX512 Manuale utente

User Guide

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Lamp

4. How To Set The Unit

5. How To Control The Unit

6. DMX512 Configuration

7. DMX512 Connection

8. Troubleshooting

9. Maintenance and Cleaning

1. Safety Instruction

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yThe unit is designed for use with the HID 150W or ELC 250W (two version). Do not use

any other type of lamp.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yDisconnect main power before fuse/lamp replacement or servicing.

yReplace fuse/lamp only with the same type.

yMake sure there is no flammable materials close to the unit while operating as it is fire

hazard.

yUse safety cable when fixes this unit. Don’t handle the unit by taking its head only, but

always by taking its base.

yMaximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is

higher than this.

yUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during

its operation. Turn off the power and allow about 15 minutes for the unit to cool down

before replacing bulb or serving.

yIn the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

yDon’t connect the device to any dimmer pack or power pack.

yDo not touch any wire during operation as high voltage might be causing electric shock.

Please read carefully the instruction, which includes important information

about the installation, usage and maintenance.

Warning

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

yNever touch bulb with bare fingers as it is very hot after using.

yHot lamp explosion hazard. Do not open the unit within five minutes after switching off.

yDo not start on the unit without bulb enclosure or housing are damaged.

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

yDo not look directly at the light while the bulb is on.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of 20

kg for each unit.

2. Technical Specification

•Voltage：AC 100V/120V/230V/250~50/60Hz, please refer to the specification lable on the

unit for the voltage.

•Bulb：HID 150W ELC 250W

•The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together

in master/slave connection, as many as required and run by built-in program chase

sequences automatically or by sound activation through an internal microphone to create

an intelligent effect.

•It can be operated by DMX 512 control or can be used as an individual unit without a

controller.

•Features different preprogrammed chase patterns.

•Please use a 3 pin XLR cable/plug when connecting units together.

•Accurate focusable optics system and ultra smooth stepping motors, Fan cooled.

•Pan: 540 deg. Tilt: 270 deg.

•Dimension: 266 x 276 x 370 mm

•Weight: 9.5 kg ( IM-200S-ELC) 10.0 kg ( IM-200S-HID)

2.1 Beam Angle

IM-200S-ELC IM-200S-HID

3. Lamp

Lamp:

HID 150W

ELC 250W

1.Always switch off the main supply and never handle the lamp or luminaries when is

hot.

2.Do not touch the bulb with bare hands. If this

happens, clean the lamp with denatured

alcohol and wipe it with a lint free cloth before

installation.

3.Never operate the lamp without appropriate

shielding.

4.In case of replacement of the lamp or

maintenance, do not open the fixture within 15

minutes after switching the power off.

5.Make sure the lamp is located in the center for

the best spot.

Diagram for Lamp changing

In case of replacement of the lamp or maintenance, do not open the fixture

within 15 minutes until the unit cools down after switching off.

3.1 HID 150W Lamp Installation Or Replacement

•Always switch power off before installing or replacing the lamp. Never try to replace the

lamp when it is hot.

•Do not touch the bulb with bare hands. Cleaning the lamp with denatured alcohol and wipe

with a lint free cloth when lamp is dirty.

1. Loose the screw on the housing cover.

2. Loose the screws of the lamp wire from terminator.

3.Remove the old lamp from the fixture.

4. Please be care to install the lamp into case, make sure it wedge tightly that it can not

move easily. WARNING: impropriety install will cause the lamp lifespan shorten and

maybe explosion during operation.

5. Connect the lamp wire to the terminator as before.

6.Please reinstall step 2 and step 1.

4. How To Set The Unit

4.1 Control Panel

Display

To show the various menus and the selected functions

LED

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

Button

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

Mains input

IEC socket and integrated fuse holder, connect to main power cable.

Only for remote control

By connect to the 1/4’’ microphone jack to control the unit for Stand by, Function and Mode

function.

Sensitivity

To adjust the sound receiving sensitivity

DMX input/output

For DMX512 link, use 3-pin XLR plug cable to link the unit together.

4.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected,

press the ENTER button to setup or it will automatically return to the main functions without

any change after idling 8 seconds. To go back to the functions without any change press the

MENU button. The main functions are showing below:

DMX 512 Address Setting

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press the ENTER button to setup or automatically

return to the main functions without any change after 8 seconds. To go back to the functions

without any change press the MENU button again.

Channel Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (8 Channel) or (11

Channel) mode. Once the mode has been selected, press the ENTER button to setup or

automatically return to the main functions without any change after 8 seconds. To go back to

the functions without any change press the MENU button again.

ShowMode

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (show 1)

or (show 2) or (show 3) or (show 4) mode. Once the mode has

been selected, press the ENTER button to setup or automatically return to the main

functions without any change after 8 seconds. To go back to the functions without any

change press the MENU button again.

Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.

Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.

Show 3 mode - Fixture is placed on the speaker, The spot is always projecting

to the audience’s direction; i.e in front of the stage. Pan

movement angle (left to right to left): 160°. Tilt movement

angle: 90° (60° above horizon; 30° below horizon.)

Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in

front of the stage. Pan movement angle (left to right to

left):160°. Tilt movement angel: 90° (vertically, front 75°;

back 15°)

Slave Mode

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(normal) or (2 light show) mode. Once the mode has been selected, press the

ENTER button to setup or automatically return to the main functions without any change

after 8 seconds. To go back to the functions without any change press the MENU button

again.

Sound Mode

Press the MENU button until the is showing on the display. Pressing ENTER button

and the display will blink. Use DOWN and UP button to select the (Led on) or

(Led off) mode. Once the mode has been selected, press the ENTER button to

setup or automatically return to the main functions without any change after 8 seconds. To

go back to the functions without any change press the MENU button again.

Blackout Mode

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(yes blackout) or (no blackout) mode. Once the mode has been selected, press the

ENTER button to setup or automatically return to the main functions without any change

after 8 seconds. To go back to the functions without any change press the MENU button

again.

Pan Inversion

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (normal)

or (pan inversion) mode. Once the mode has been selected, press the ENTER

button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the MENU button again.

Tilt Inversion

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(normal) or (tilt inversion) mode. Once the mode has been selected, press the

ENTER button to setup or automatically return to the main functions without any change

after 8 seconds. To go back to the functions without any change press the MENU button

again.

Led Display

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

10D

(Led on) or (Led off) mode. Once the mode has been selected, press the ENTER

button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the MENU button again.

Test

Press MENU button up to when the is show on the display.

Pressing ENTER button and the unit will run test by built in program and can test by

program. Back to the functions press MENU button again.

Manual Test

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

. Once the mode has been selected, press the ENTER

button to confirm, the display will blinking, use DOWN and UP button to test. To go back to

the functions without any change press the MENU button.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the MENU button again.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the MENU button again.

Reset

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and all channels of the unit will return to their standard position. To go back to the

functions without any change press the MENU button again.

11D

4.3 Home Position Adjust

Press MENU button for at least 5 seconds into offset mode to adjust the home position, use

DOWN and UP button up to the function (Pan, Tilt, Color, Gobo) shown on the display.

Pressing ENTER button and the display will blink. Use DOWN and UP button to adjust the

home position. Once the position has been selected, press the ENTER button to setup or

automatically return to the offset functions without any change press the MENU button again,

To go back to the main functions without any change after 8 seconds.

5. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By iLead controller ( please refer to the user guide of iLead ) or universal DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will show 200S on the

display and move all the motors to their ‘home’ position and you may hear some noises for

about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in

programs.

5.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other units to

give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show. You have to set the first unit in master mode and select

(show 1) or (show 2) or (show 3) or (show 4) mode. Its

DMX input jack will have nothing plugged into it, and Its master LED will be constantly on

and sound LED will flash to the music. The other units will have to set in slave mode

and select (normal) or (2 light show) mode, Their DMX cables plugged into

the DMX input jacks (daisy chain) and the slave led lights will constantly on.

2-light show

In (slave mode), means the unit works normally and means

2-light show. In order to create a great light show, you can set on the second unit to

get contrast movement to each other, even if you have two units only.

12D

5.2 Easy Controller

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit, you will find that the remote control on the first unit will

control all the other units functions press the MENU button again.

Stand By Blackout the unit

Function 1. Sync. Strobe

2. Two-light strobe

3. Sound Strobe

Select Show

1-4 Select

Gobo/Color X/Y moving setting

1.Pan position

2.Tilt position

3.Dimmer

First set Master unit,

then set Slave units’

position

Mode Sound

(LED OFF) Show

(LED Slow Blinking) LED ON Position/ Latch

(LED Fast Blinking)

5.3 iSolution Operation

♦Consistent DMX configuration enable iMove to be linked together with iRock and iShow

and controlled at the same time.

♦DMX address can be set remotely by iLead controller (Please refer to the user manual of

iLead controller). No need to calculate the DMX channels of each fixture in the chain.

♦Automatic switching between DMX function and built-in stand alone programs.

5.4 DMX Controller

An universal DMX controller to control the units, you have to set DMX address from 1 to 512

channel so that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press and keep ENTER button pressed up to when

the display stops blinking or storing automatically 8 seconds later. To go back to the

functions without any change press the MENU button again. If you use please refer to the

following diagram to address your DMX512 channel for the first 4 units.

DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX

channels of each fixture in the chain.

13D

6. DMX 512 Configuration

NOTICE：When you control the units by DMX controller and the value of the 8th channel is

between 240 and 255, the units enter into standalone operation, other channels (1-7) will not

be controlled by DMX controller.

14D

NOTICE：When you control the units by DMX controller and the value of the 6th channel is

between 16 and 255, then the channel1 and channel2 will be out of control. Or if the value of

the 8th channel is between 240 and 255, the units enter into standalone operation, other

channels will not be controlled by DMX controller.

15D

7. DMX512 Connection

The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm

1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it

in the DMX-output of the last unit.

3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to

the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is

a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,

when power is disconnected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) ,

Pin4/5: not used.

16D

8. Troubleshooting

Following are a few common problems that may occur during operation. Here are

some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the unit or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the

master/ slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Make sure the unit does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

F. The lamp is cutting out intermittently

1. The lamp is not working well. Check the main voltage either too high or too low.

2. Internal temperature may be too high. Check and if necessary replace the fan on the

head.

17D

G. If The pan belt is broken

1. Turn off the main power.

2. Unscrew all the screws and open the base-housing cover.

3. Unplug all the connect wires that from the arm.

4. Unscrew the screws that fix the axis gear.

5. Change a new belt by going through all connects wires that from the arm to base, and

through the bridge for correct position.

6. Set up the gear axis to the bridge and screwed it. Note: do not press the belt.

7. Put the belt around the axis gear and motor gear.

8. Plug all the connect wires that form the arm.

9. Adjust the pan home position.

10. Screw the base-housing cover.

18D

9. Maintenance and Cleaning

Maintenance (for HID lamp only):

Filter,capacitor Ignitor Ballast

A. As the pictures shown above, if the cable or cable joints turned yellow or black,

please replace the cable or cable joints immediately.

B. Do maintain the fixtures every two months and make sure that all the screws

and terminals have been locked firmly to make sure the normal performance

of the fixtures. Negligence of maintenance would cause malfunction of the

fixture.

Cleaning:

The cleaning of internal and external optical lenses and/or mirrors must be

carried out periodically to optimize light output. Cleaning frequency depends on the

environment in which the fixture operates: damp, smoky or particularly dirty

surrounding can cause greater accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least

every 30/60 days.

19D

EC Declaration of Conformity

We declare that our products (lighting equipments) comply with the

following specification and bears CE mark in accordance with the

provision of the Electromagnetic Compatibility (EMC) Directive

89/336/EEC.

EN55014-2: 1997A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

Innovation, Quality, Performance

Altri manuali per DMX512

Indice

Altri manuali iSolutions Attrezzatura di illuminazione

iSolutions

iSolutions Xperior 700SZ Spot Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente

iSolutions DMX512 Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche