Itam PT-7200 Manuale utente

For sale and use in :

AT, BE, BG, CH, CY, CZ, DE, DK, EE, ES, FI, FR,

GB, GR, HU, IE, IT, LT, LU, NL, NO, PL, PT, RO,

SE, SI, SK

PT-7200 UHF / VHF

Handfunkgerät

Handheld Transceiver

Bedienungsanleitung

Manual

Manuale d’uso

TEAM Electronic GmbH

Bolongarostrasse 88; D-65929 Frankfurt am Main, Germany

phone ++49 / 69 / 300 950 0 - fax ++49 / 69 / 31 43 82

www.team-electronic.de - [email protected]

WEEE - Reg. Nr. DE 91930360 8 ( EAR ), 50635 ( ERA )

GRS-Nr. 10001374

DSD 2617305, ARA 2284

manual_pt-7200_2.qxp 22.07.2008 14:52 Seite 1

22 23

Dear Customer,

we thank you for the purchase of the PT-7200. Please read this instruc-

tion manual carefully before using the PT-7200 for the first time. You will

learn about the different features and functions of your new handheld

transceiver.

The use of commercial frequencies requires a licence. For more informa-

tion about the regulations, fees and applications contact your local gov-

ernment agency in charge of telecommunication.

We recommend, to get the radio programmed by an authorized TEAM

dealer. The radio has to be programmed according to the restrictions of

the individual licence of the user.

Safety

It is important that the user is aware of and understands hazards com-

mon to the operation of any transceivers.

Warning!

Turn off your transceiver prior to entering any area with a potentially

explosive atmosphere (where the air contains gas, dust and smog,

etc.), e.g. gasoline service stations.

Precautions in Use

Please follow the instructions to avoid fire, bodily injury and damage of

the transceiver.

It is recommended not to exceed the maximal times for transmission

(1 minute) and reception (4 minutes) since these operation tasks gen-

erate heat. Too much heat may cause damage.

Please do not disassemble or assemble the transceiver under any cir-

cumstances.

Please do not expose the transceiver to direct sunlight for a long time;

do not place the transceiver near any heating devices, either.

Please do not put the transceiver in extremely dusty or moist places;

do not place it on unstable surfaces, either.

If the transceiver emits smoke or strange odors, turn it off, remove the

battery from the transceiver and immediately contact your authorized,

local TEAM Electronic dealer.

Contents page

1 Unpacking and Checking 23

1.1 Supplied Accessories 23

2 Preparation 23

2.1 Battery Info 24 - 26

2.2 Battery Care Tips 26 - 27

2.3 Battery Recycling and Disposing 27

2.4 Charging the Battery 27

3 Accessories 28

3.1 Installing/Removing the Battery Pack 28

3.2 Installing the Antenna 28

3.3 Installing the Belt Clip 28

3.4 Installing the Dust Cover 28

3.5 Connecting the Accessory 28

4 Getting Acquainted 29

4.1 Radio Overview 29

5 Basic Operation 30

6 Programmable Dual Keys 30 - 34

Annunciation Type Selection 31

Whisper 31

Talkaround 31

Call 1 / 2 / 3 / 4 31

Lone Work 32

Emergency Call Cancel Call 32

Scan 32

Noise Channel Delete 32

Call Forward 32

High / Low Power 32

Squelch Adjust 33

Monitor Momentary 33

Monitor 33

Squelch Off Momentary 33

Squelch Off 33

Lock Keyboard 33

Compander 33

Scrambler 33

Battery Check 33

Rental Time Check 33 - 34

7 Auxiliary Functions 34

7.1 Vox 34

7.2 Wire Clone Mode - 34

7.3 Time-Out-Timer 35

7.4 Power Save 35

7.5 Low Battery Level Alert 35

7.6 CTCSS / DCS 35

7.7 5-Tone Selective Calling 36

7.8 DTMF 36

8 Specification 37

9 Programmed Settings 38 - 41

GB GB

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 23

24 25

1 Unpacking and Checking

Unpack the transceiver set carefully. We recommend that you identify

the listed items before discarding the packing material. If any items are

missing or have been damaged during shipment, please contact the

dealer immediately.

1.1 Supplied Accessories

1 x Antenna 1 x Belt clip 1 x Dust cover

1 x Screw 1 x Battery 1 x Charger

1 x Power adapter 1 x User's Manual 1 x Hand strap

2 Preparation

2.1 Battery Precautions

CAUTION

1) Do not attempt to charge a fully charged battery pack. Doing so,

may shorten the lifetime of the battery pack or the battery pack may

get damaged.

2) Upon completion of charging process, disconnect the battery pack

from the charger. If the charger power is reset (turned ON after

being turned OFF), recharging will start again and the battery pack

will be overcharged.

3) Do not use the transceiver while charging the battery pack. We re-

commend you switch the transceiver power OFF during charging.

4) Do not expose the battery pack to heat or fire.

5) Never attempt to remove the casing from the battery pack.

DANGER!

1) Do not disassemble or reconstruct the battery pack!

The battery pack has a safety function and protection circuit to avoid

danger. If they suffer serious damage, the battery may generate

heat or smoke, rupture, or burst into flame.

2) Do not short-circuit the battery!

Do not join the + and - terminals using any form of metal (such as a

paperclip or wire). Do not carry or store the battery pack in contain-

ers holding metal objects (such as wires, chain-necklace or hair-

pins). If the battery pack is short-circuited, excessive current will

flow and the battery may generate heat or smoke, rupture, or burst

into flame. It will also cause metal object to heat up.

3) Do not apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate

heat or smoke, rupture, or burst into flame.

4) Do not place the battery near fires, stoves, or other heat sources!

If the polymer separator melts due to high temperature, an internal

short-circuit may occur in the individual cells and the battery may

generate heat or smoke, rupture, or burst into flame.

5) Do not immerse the battery in water or get it wet by other means!

If the battery's protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke, rup-

ture, or burst into flame.

6) Do not charge the battery near fires or under direct sunlight!

If the battery's protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke, rup-

ture, or burst into flame.

7) Use only the specified charger and observe charging require-

ments!

If the battery is charged in unspecified conditions (under high tem-

perature over the regulated value, excessive high voltage or cur-

rent over regulated value, or with a remodeled charger), it may

overcharge or an abnormal chemical reaction may occur. The bat-

tery may generate heat or smoke, or burst into flame.

8) Do not pierce or strike the battery with any object or step on it!

This may break or deform the battery, causing a short circuit. The

battery may generate heat or smoke, rupture, or burst into flame.

9) Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into flame. If the battery's protection circuit is

damaged, the battery may charge at an abnormal current (or volt-

age), and an abnormal chemical reaction may occur. The battery

may generate heat or smoke, rupture, or burst into flame.

10) Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

flame.

11) Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or

burst into flame.

12) Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of current

may flow upon discharging. The battery may generate heat or

smoke, rupture, or burst into flame.

13) Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating equip-

ment, do not force it; check the polarity of the battery. If the battery

GB GB

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 25

26 27

pack is reverse-connected to the charger, it will be reverse-charged

and an abnormal chemical reaction may occur. The battery may gen-

erate heat or smoke, rupture, or burst into flame.

14) Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash your

eyes out with fresh water as soon as possible, without rubbing your

eyes. Go to the hospital immediately. If left untreated, it may cause

eye-problems.

WARNING

1) Do not charge the battery for longer than the specified time!

If the battery pack has not finished charging even after the regulat-

ed time has passed, stop the charging process. The battery may

generate heat or smoke, rupture, or burst into flame.

2) Do not place the battery pack into a microwave or highpressure

container!

The battery may generate heat or smoke, rupture, or burst into

flame.

3) Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from flammable areas. Electrolyte leaking

from battery can easily catch on fire and cause the battery to gen-

erate smoke or burst into flame.

4) Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different color-

ing, is deformed, or seems abnormal for any other reason, remove it

from the charger or operating equipment and do not use it. The bat-

tery may generate heat or smoke, rupture, or burst into flame.

2.2 Battery Care Tips

The transceiver is equipped with a TEAM Li-Poly battery pack. The

following tips help you to get the best battery performance and pro-

loged battery life.

1) Charge the new battery pack continuously for 4~5 hours before its

initial using, which ensures the maximum battery capacity and best

performance in using.

2) Do not attempt to charge the TEAM battery pack in any other charg-

er than the one included in the scope of delivery.

3) The battery pack can be charged while in the transceiver, and to

ensure it is fully charged it's recommended to charge the battery

pack with the transceiver turned off.

4) The ideal temperature to store the battery pack is 25 (room tem-

perature). Charging the battery pack at a low temperature (below

0°C) will cause electrolyte leakage and damage to the battery pack.

5) Charging the battery pack at a high temperature (above 35 °C ) will

cause decrease in battery discharge capacity and affect the trans-

ceiver performance.

6) The new or used battery should be stored in a cool and dry place.

7) If recharge the battery pack after long storage, you should

charge it continuously for 4~5 hours.

8) Do not leave the transceiver and the battery in the charger when

not charging. Overlong charging will shorten the battery life.

(Please do not use the charger as the transceiver's mounting

bracket.)

2.3 Battery Recycling and Disposing

After the battery life expires, the Li-Poly battery pack has to be recy-

cled. Please , however, the recycling facilities are not available every-

where. TEAM goes in for the recycling of all the rechargeable batter-

ies. For more details please contact your local TEAM distributor.

2.4 Charging the Battery

A new battery, or a battery with low power level needs to be

charged completely.

Left LED - Red The battery is in the state of charging.

Middle LED - Green The battery is fully charged or the battery

is not inserted properly into the charger.

Right LED - Yellow The battery temperature is abnormal or the

battery is defect.

1) Connect the power adapter with the battery charger. Plug the

adapter into an AC wall outlet and the indicator turns green.

2) Place the battery or transceiver into the charger slot. The indicator

turns red or flashes, then the charger gets in the state of charging

automatically. Charging time depends on battery capacity. When

battery is fully charged the middle LED turns green.

Notes:

1) The battery is not fully charged in the factory.

Before the initial use, please charge the new battery continu-

ously for 4~5 hours.

2) The charger will stop charging and the left, red LED will go off.

If the charger detects a damaged battery or if the temperature

of the battery is too high, then the right LED will light yellow.

3) The charger detects if the battery is fully charged and stops

charging.

4) Partly charged battery packs will be discharged first, before

charging process starts.

GB GB

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 27

28 29

3 Accessories

3.1 Installing/Removing the Battery Pack

To install the battery pack:

1) Match the two bulges, located at the bottom of

the of the battery pack, with the corresponding holes at the rear

bottom of the transceiver;

2) Then firmly press the battery pack downwards

to lock it in place until a click is heard.

To remove the battery pack:

Push the latch with your thumb to unlock the battery

pack. Carefully remove the battery pack.

3.2 Installing the Antenna

Screw the antenna into the connector at the top of the

transceiver by holding the bottom of the antenna and turn-

ing it clockwise.

3.3 Installing the Belt Clip

Match the grooves of the belt clip with those on the rear

of the battery pack. Then press the belt clip downwards to

lock it in place.

3.4 Installing the Dust Cover over the Versatile Connector

When not using the optional Speaker/Microphone, use the dust

cover over the versatile connector with the supplied screw.

3.5 Installing the Optional Speaker / Microphone

The connection plugs of the PT-7200 accesssories have

a guide pin and a screw attached.

Position the guide pin, then ensure that the contacts of

connector and jack are in place. Next, thighten the screw.

Notes:

Only use the original TEAM accessories for the PT-7200.

Optional accessories, e.g. ear- / microphone, are not included in

the scope of delivery.

4 Getting Acquainted

4.1 Radio Overview

1 Antenna

2 LED Indicator

> Lights red in transmission mode;

> Lights green in reception mode;

>Flashes orange when receiving authorized DTMF and 5-Tone

signals.

> Flashes red when battery level is low. 3 Channel Selector

3 Rotary Channel Selector - select channel 1-16.

4 Power/Volume Switch

Turn clockwise to switch on the radio. Turn counterclockwise till

a click is heard to switch off the radio. Rotate to adjust the vol-

ume after turning on the radio.

5 Side Key 1

Programmable double-function key: Press short for acitivation of

first function and long for second function.

6 PTT (Push-to-talk)

To make a call, press and hold the PTT button, then speak into

the microphone with normal voice. Release the PTT button to

switch to reception mode.

7 Side Key 2

Programmable double-function key: Press short for acitivation of

first function and long for second function.

8 Top Key (Emergency Button)

Programmable double-function key: Press short for acitivation of

first function and long for second function. Recommended for

emergency functions.

9 Microphone/Speaker Jacks

For connection of accessory, programming cable and clone

cable.

GB GB

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 29

30 31

5 Basic Operation

Power On

Switch on the radio by turning the Power/Volume switch clockwise

until a click is heard. If programmed, a beep tone is audible and the

actual channel is announced.

Channel Selection

For setting the channel 1 - 16, rotate the channel selector. If voice

annunciation is activated, the actual channel is announced.

Transmission Mode

To transmit a signal, press PTT, and speak in normal voice with a

distance of 5 cm to microphone.

To transmit without pressing the PTT key, program the Vox func-

tion.

When transmitting a signal the LED lights red.

Reception Mode

By default, the radio is in reception mode. The LED lights green

when a signal is received.

6 Programmable Dual-Keys

Each of the three dual-keys can be programmed with a maximum

of two functions. Function 1 is triggered by pressing the key short-

ly. Function 2 is acitvated / deacitvated by the pressing the key

long. The required time period, for triggering function 2, can be pro-

grammed.

The assignment of the functions to the keys are programmed via

software. More information about programming the various func-

tions and their settings can be found in the manual of the software

T-UP10.

GB GB

Available Functions

None

Annunciation Type Selection

Whisper

Talkaround

Call 1 / 2 / 3 / 4

Lone Work

Emergency Call

Cancel Emergency Call

Scan

Noise Channel Delete

Call Forward

High / Low Power

Squelch Adjust

Monitor Momentary

Monitor

Squelch Off Momentary

Squelch Off

Lock Keyboard

Compander

Scrambler

Battery Check

Rental Time Check

None

No function assigned

Annunciation Type Selection

On / Off english voice annunciation

Programmable options: male / female either only channel or chan-

nel and functions.

Whisper

On / Off whisper mode

The microphone gain can be increased by a max. of 4 dB to allow

whispering in necessary situations.

The gain level for the internal and the external microphone can be

set differently.

Talkaround

On / Off talkaround repeater

When set up for repeater operation, all signal are directed to the

repeater. With the function Talkaround, repeater operation can be

deactivated and the direct communication with other radios within

the range of reception is possible.

Call 1/2/3/4

For each channel, a maximum of four selective calls can be pro-

grammed (Call 1/2/3/4). The call will be send by pressing the pro-

grammed dual-key.

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 31

32 33

GB GB

Lone Work

On / Off Lone Work Function

Function secures workers in ciritical environments.

In determinably time intervals, a beep tone reminds the lone wor-

ker to give feedback to the controlling station by pressing any key

periodically. If no feedback is given, the radio switches to emergen-

cy mode.

Emergency Call

Switch on the emergency alarm.

This function can only be assigned to the orange-colored, top key

of the radio. The various settings of the emergency function are

explained in the manual of the software T-UP10.

Cancel Emergency Call

Turn off the emergency alarm

This function can only be assigned to the orange-colored, top key

of the radio.

Scan

On / Off Channel Scanning

Via software one of a maximum of sixteen scan lists can be assi-

gned to each channel.

Each scan list stores the selected channels that are to be scanned,

as well as two priority channels and a variety of scan settings.

When scanning is activated, all programmed channels are sear-

ched; in a ring system; for signals. By default, the LED blinks red,

while scanning is activated. If a signal is detected, the scan functi-

ons stops, the radio remains on this channel and the LED lights

green, until the signal ends. Then, scanning continous until anot-

her signal is detected

For each scan list, the individual parameters, e.g. hold time, can be

programmed.

Priority Channel

A maximum of two priority channels can be programmed for each

scan list.

The scan function stops immediately when a signal is present on

the programmed priority channels. The radio remains on the busy

channel until the signals ends.

Noise Channel Delete

On / Off Noise Blanker

Call Forward

On / Off Call Fowarding

H/L Power

Switches between Tx powers high and low if acitvated via software.

Squelch Adjust / Call Cancel

This function is only available with activated voice annunciation.

With each press of the assigned key, the programmed squelch

level ( 0 - 9) is increased by one. After level 9 is reached, the

adjustment jumps back to zero.

Monitor Momentary / Call Cancel

The actual channel is scanned for signals. If a signal is present, the

squelch is deactivated and the signal is audible. If no signal is pre-

sent, the squelch remains activated. The monitor function is only

activated as long as the assigned key is pressed.

Monitor / Call Cancel

Monitor function On / Off

Squelch Off Momentary

The squelch off function is only activated as long as the assigned

key is pressed.

When the squelch is turn off, all signals on the channel are audible

and a constant noise can be heard.

Squelch Off / Call Cancel Rauschunterdrückung Aus

Squelch On / Off

Lock Keyboard

Keylock On / Off

Locks the channel selector to avoid accidental channel change.

The PTT key and the dual-function keys are not affected by the

keylock function.

Compander

Compander On / Off

Improves weak signals

Scrambler

Scrambler On / Off

The scrambler distorts the signal, which cannot be understood by

radios that do not have the same scrambler function acitivated. To

be able to hear the scrambled signal in the original way, it must be

de-scrambled.

Battery Check

Tests the power level of the battery

This function is only available with activated voice annunciation.

The power level is described by the numbers 1 - 4, with number 1

indicating a low power level and number 4 indicating a high power

level.

Rental Time Check

Announces the remaining rental time

This function is only available with activated voice annunciation.

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 33

34 35

GB GB

The remaining rental time is annouced with the numbers 1 -4. Via

software three control times (Remaining Time 1/2/3) can be pro-

grammed

The remaing time between the start of the programmed rental time

and Remaining Time 1 is announced with the number 4. The time

between Remaining Time 1 and 2, is announced with the number

3, etc. Is the remaining beyond Remaining Time 3, number 1 is

announced.

7 Additional Functions

The following functions have to be programmed with the software

T-UP10. More information about the possible settings of these

functions can be found in the software manual.

7.1 VOX

With activated Vox function, voice-controlled transmission, without

PTT key operation, is possible.

There are various settings for this function, e.g. sensitivity, hold

time after end of signal, etc.

7.2 Wire Clone Mode

Data transfer from radio to radio via optional cable.

1. Turn both PT-7200 off.

2. Connect both radios via data transfer cable.

3. Set both radios to the same channel.

4. Turn the receiving radio on - the radio onto which the data should

be transferred.

5.At the transmitting radio, the one which data should be copied, hold

the two programmable dual key (above and below the PTT key)

while the radio is turned on.

The LED lights shortly orange and the command “clone” is

announced if the voice annunciation is activated.

6. At the transmitting radio, press the PTT key to start data transfer.

The LED starts to blink red.

At the receiving radio, the LED lights green.

After completion of the data transfer, a confirmation tone is

emmited at the transmitting radio.

7.3 Time-Out-Timer (TOT)

To avoid excessive occupation of a channel, the TOT function can

be set up.

The maximum transmit time (between 15 and 1200 seconds in 5

seconds-steps) can be programmed via software. When the maxi-

mum value is reached, transmission is stopped automatically and

an alarm tone is audible (default setting) until the PTT key is

released.

A warning tone, which annouces the soon end of the TOT limit can

be programmed.

7.4 Power Save Type

The Power Save Function reduces the power consumption. The

radio switches automatically into Power Save Mode when no

signal is received and the radio is not operated.

The sleep times can be adjusted (short, middle, long).

7.5 Low Battery Level

A low battery warn function can be programmed. Once the power

level falls below a certain level, the LED blinks red and the radio

omits some alarm tones.

Now, it is time to charge the battery pack.

7.6 CTCSS / DCS

With the CTCSS and DCS coding system, unwanted signals can

be filtered out. It is possible to make only those signals audible,

which are encoded with the same CTCSS / DCS code.

Signals that are not encoded with the same code will be not be

audible, although they are present and can be heard with the

squelch of or monitor function.

There are 52 CTCSS and 198 DCS codes available.

Attention:

The use of CTCSS and DCS codes does not guarantee privacy.

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 35

36 37

GB GB

7.7 5-Tone Selective Calling

For 5-Tone Selective Calling, there are seven standards (CCIR1/2,

ZVEI1/2/3, EEA und EIA) and two user-defined formats available.

For the user-defined formats, the tone-frequency, -length and the

spaces between them can be defined.

A maximum of 32 encoder telegrams, composed of a maximum of

three 5-tone sequences, can be programmed.

A maximum of four individual and / or group encoding telegrams,

can be assigned.

A maximum of 16 telegrams can be decoded per channel.

For each encode-telegram, these commands are available: Gene-

ral, Incoming Emergency, Priority, Security Inquire, Emergency Exit,

Stun, Kill, Revive,Active, Clear Down, Silent Interrogate, ACK1 Rin-

ging, ACK1 Authorisation.

It can be programmed whether the signal is only audible at those

radios that are called or audible at all radios on the actual channel.

Furthermore, acknowledgement, if selected, can be manual or

automatic.

7.8 DTMF

ADTMF telegram consists a maximum of three sequences.ADTMF

sequence can be composed of max. 20 digits (0 - 9, A - D).

8 Specifications

PT-7200

Channel Number 16

Channel Separation 12,5 KHz / 20 kHz / 25 kHz

Modulation Type FM

Deviation narrow : 2.5 kHz / wide : 5 kHz

RX-Sensitivity narrow : 0.28 μV at 12.5 kHz /

wide: 0.75μV at 25 kHz

Audio Output Power 0.50 W at 8 Ohm with 10 % THD

Supply Voltage 6 - 8 V

Battery Pack Li-Poly, DC 7.2 V / 1700 mAh

Dimensions B/H/T: 56 x 120 x 35 mm

Weight 332 g (with antenna and battery pack)

Modell: PT-7200 VHF:

Frequency Range 136 - 174 MHz

TX Power max. 5 W

Modell: PT-7200 UHF:

Frequency Range 430 - 470 MHz

TX Power max. 4 W

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 37

38 39

GB GB

9 Programmed Settings

Model : Serial Number:

Hardware Version: MCU-Version :

Dual-Key Programming

Short Button (short press) Long Button (long press)

SK #1

SK #2

TK #3

Scan List Channels Prioritiy Channels

Programmed Scan Lists

Channel Information

Chan

nel TX

(MHz) RX

(MHz) TX

CTCSS/DCS RX

CTCSS/DCS Bandwidth

12.5/20/25kHz TX Power

High Scan List Personality

Template Beat Shift

manual_pt-7200_2.qxp 22.07.2008 14:53 Seite 39

Indice

Altri manuali itam Ricetrasmettitore

itam

itam TORKY Manuale utente

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente

itam PT-7200 Manuale utente

Manuali Ricetrasmettitore popolari di altre marche