ivanti ISA6000 Istruzioni per l'installazione

ISA6000 Hardware Guide

Copyright Notice
This document is provided strictly as a guide. No guarantees can be provided or expected. This
document contains the confidential information and/or proprietary property of Ivanti, Inc. and its
affiliates (referred to collectively as “Ivanti”) and may not be disclosed or copied without prior written
consent of Ivanti.
Ivanti retains the right to make changes to this document or related product specifications and
descriptions, at any time, without notice. Ivanti makes no warranty for the use of this document and
assumes no responsibility for any errors that can appear in the document nor does it make a
commitment to update the information contained herein. For the most current product information,
please visit www.Ivanti.com.
Copyright © 2022, Ivanti, Inc. All rights reserved.
Protected by patents, see https://www.ivanti.com/patents.
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 2 of 49

Contents
Revision History 4
System Overview 5
Introduction 5
LED Control Panel 5
Control Panel LEDs 6
Management Port LEDs 7
INT and EXT Port LEDs 7
Air Flow Estimate 8
Air Flow Direction 8
Beeping and Alarms 8
Hardware Specifications 9
System Measurements 9
Power Rating 9
Power Consumption 9
Environmental Requirements 10
Component Specifications 11
Where to Get Replacement Components 11
Console and Initial Configuration 12
Accessing ISA6000 Serial Console through Laptop 12
Accessing ISA6000 Console through Console Server 12
Powering On the System 13
Configuring Basic Settings 13
Accessing the Web Admin Interface 14
Licensing the System 14
Installation 16
Preparing for Setup 16
Rack Mounting Instructions 18
Standard Warnings and Compliance 20
About Standard Warnings 20
Safety Certifications 20
Electrical Safety 20
General Safety 21
Installation Instructions 24
Circuit Breaker 26
Power Disconnection Warning 28
Equipment Installation 30
Restricted Area 32
Redundant Power Supplies 35
Backplane Voltage 37
Comply with Local and National Electrical Codes 39
Product Disposal 41
Power Cable and AC Adapter 43
Certification Statements 47
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 3 of 49

System Overview
Introduction
The ISA6000 features a unique and highly optimized design for low wattage processor platforms. It is
equipped with a high-efficiency low noise power supply. High-performance fans provide ample
optimized cooling.
For added system security, the USB ports have been disabled.
LED Control Panel
The control panel located on the front of the ISA6000 chassis includes power control buttons and status
LEDs. This section describes the LED indicators and the appropriate responses.
Control Panel Buttons
The control panel includes a power on/off button and a reset button.
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 5 of 49
System Overview

Power: The main power switch is used to apply or remove power from the power supply to the server
system. Turning off system power with this button removes the main power but keeps standby power
supplied to the system. Therefore, you must unplug system before servicing.
Reset: The reset button is used to reboot the system.
Control Panel LEDs
The control panel displays five LEDs to monitor the system.
Information LED: Alerts operator of several states, as noted in the table below:
Status Description
Continuously on and
red
An overheat condition has occurred. This may be caused by cable
congestion.
Blinking red (1Hz) Fan failure; check for an inoperative fan.
Blinking red (0.25Hz) Power failure; check for a non-operational power supply.
NIC1 (GLAN1): Associated with the Management port. It indicates network activity when flashing.
NIC2 (GLAN2): Unused. Will always be off.
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 6 of 49
System Overview

HDD: Indicates IDE channel activity or SATA drive activity when flashing.
Power: Indicates power is being supplied to the system power supply. This LED should be illuminated
when the system is operating.
Management Port LEDs
The management port has two LEDs. The yellow LED indicates activity, while the link LED may be green,
amber, or off to indicate the speed of the connection.
LED Color Description
Activity Yellow (flashing) Active
Link Off No connection
Orange 1 Gbps speed
Green 100 Mbps speed
INT and EXT Port LEDs
Two LAN ports are located on the NIC card. Each Ethernet port has two LEDs.
LED Color Description
Activity Yellow (blinking) LAN Active
Link Off 10 Mbps link speed or no connection
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 7 of 49
System Overview

LED Color Description
Orange 1 Gbps link speed
Green 10 Gbps link speed
Air Flow Estimate
Equipped Cooling Fan and/or Active CPU Heat
Sink
Estimated
Overall
System Air
Flow Rate
When All
Four
Cooling Fans
Operated at
Full Speed
4x Cooling FAN + 1 passive CPU Heat Sink 29 CFM
Air Flow Direction
The following table gives the air flow direction of the power supply fan and internal CPU fan.
Component Air Flow Direction
Power Supply Fan To the rear of the unit
Internal CPU Fan To the rear of the unit
Beeping and Alarms
Beep Code Description
5 short beeps + 1 long beep every 5 seconds No memory detected in the system
Continuous beep (“i” LED on front panel turns RED) System overheat condition
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 8 of 49
System Overview

Hardware Specifications
This chapter describes the specifications and components for ISA6000.
System Measurements
These figures are for an unpackaged and packaged system.
Category ISA6000 Shipping Box
Form factor 1U chassis
Width 17.2" (437mm) 17.5” (444.5mm)
Height 1.7" (43mm) 8” (203.2mm)
Depth 11.3" (287mm) 23” (584.2mm)
Weight Net Weight: 10 lbs (4.54 kg) Net Weight: 15.2 lbs (6.9 kg)
Power Rating
Below is the maximum power rating for the power supply:
Category ISA6000
Power type Single-phase
Input voltage range 100 - 240V
Input current 2.6 Amps maximum
Input wattage 200W
Input frequency range 50 – 60Hz
Power Consumption
A power consumption estimate is usually around 15% to 20% higher than the actual power
measurement. The user’s system power consumption may vary based on the workload and
environment.
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 9 of 49
Hardware Specifications

This power consumption data mentioned in the tables below is worst-case scenario and is
meant for reference only
Devices
Max
Pwr
(W)
Actual
Pwr(W)
+12V
current
(A)
+5V
current
(A)
+3.3V
current
(A)
+5VSB
current
(A)
-12V
current
(A)
Motherboard:
Motherboard 21.2 21.2 1..5 0.7 0.1
Processor 65.0 65.0 5.4
Memory 3.0 3.0 0.3
USB
Peripherals
(Generic)
2.5 2.5 0.5
Motherboard
Total:
91.7 91.7 7.1 1.2 0.1 0.0
Fans (Qty 4): 21.6 21.6 1.8 0.0
Storage
Drives:
5.0 5.0 0.0 0.0 0.0 0.0
Total Current 8.9 1.2 0.1 0.0 0.0
Total Power 118.3 113.7
Environmental Requirements
Category ISA6000
Operating temperature 5°C - 35°C (41°F - 95°F)
Non-operating temperature -40°C to 70°C (-40°F to 158°F)
Operating Relative humidity 8% to 90% (non-condensing)
Non-operating Relative humidity 5% to 95% (non-condensing)
Copyright © 2022, Ivanti.Inc. All Rights Reserved. Privacy and Legal.
Page 10 of 49
Hardware Specifications
Indice
Altri manuali ivanti Hardware di rete
Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor
Yudor YDS-16 Manuale utente

D-Link
D-Link ShareCenter DNS-320L Manuale utente

Samsung
Samsung ES1642dc Istruzioni per l’uso

Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio













