J-Tech Digital JTECH-HDBT73 Manuale utente
Operating Instructions
Website: www.jtechdigital.com
Toll Free: 1-888-610-2818
Email: support@jtechdigital.com
USER MANUAL
J-Tech Digital® HDBaseT Extender 4K@60HZ 4:2:0
Model: JTECH-HDBT73
JTD-ID: 73
The HDBaseT Extender 4K@60HZ 4:2:0 Control Path has been tested for
conformity to safety regulations and requirements, and has been certified for
international use. However, like all electronic equipment, the JTECH-HDBT73
should be used with care. Please read and follow the safety instructions to protect
yourself from possible injury and to minimize the risk of damage to the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this
manual.
Provide proper ventilation, air circulation, and do not use near water.
Keep objects that might damage the device away and assure that the placement
of this unit is on a stable surface.
Use only the power adapter, power cords, and connection cables designed for
this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.
SAFETY AND NOTICE
INTRODUCTION .......................................................................................................1
PACKAGE LIST.........................................................................................................1
FEATURES................................................................................................................1
PANEL DESCRIPTION .............................................................................................2
SYSTEM CONNECTION...........................................................................................3
SPECIFICATION .......................................................................................................4
PANEL DRAWING .................................................................................................... 5
TROUBLESHOOTING & MAINTENANCE................................................................6
TABLE OF CONTENTS
The JTECH-HDBT73 is an HDBaseT Extender set consist of transmitter (TX) and
receiver (RX). It distributes HDMI signal via CAT5e/CAT6a cable at 70m/PoC, and
enables IR and RS232 pass-through to control local source device from remote or
far-end display.
1x Transmitter (TX)
1x Receiver (RX)
2x TX Mounting Ears with 2 Screws
2x RX Mounting Ears with 2 Screws
4x TX Plastic Cushions
4x RX Plastic Cushions
1x IR Receiver
1x IR Emitter
2x 3-pin Phoenix Connector
1x Power Adaptor (12VDC, 1A)
1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.
Supports HDMI 1.4 & HDCP 2.2.
Maximum transmission distance is up to 40m for 4Kx2K, and 70m for 1080p.
Supports bi-directional 5V IR and RS232 pass-through for long-distance control.
Supports bi-directional PoC for simplified wiring.
Supports CEC.
Features DIP switcher for choosing Control or Update mode.
INTRODUCTION
PACKAGE LIST
1
FEATURES
No.
Name
Description
①
Power LED
Illuminates red when power is applied.
②
RS232
Euroblock/Phoenix connector for connecting an
RS232 data device.
③
HDMI IN (TX)
HDMI port for connecting the video source device
(e.g. Blu-ray DVD)
HDMI OUT (RX)
HDMI port for connecting the video display.
④
CTRL/UPDATE
Switch for determining the behavior of the RS232
connection.
When in the CTRL position, it serves as an RS232
serial extender.
When in the UPDATE position, it allows you to
update the Valens IC program by connecting to a
PC and running the batch file.
⑤
HDBT OUT (TX)
RJ45 jack for connecting the Cat5e/6 cable to the
Receiver.
HDBT IN (RX)
RJ45 jack for connecting the Cat5e/6 cable to the
Transmitter.
⑥
IR IN
3.5mm jack for connecting an IR Receiver (not
included).
⑦
IR OUT
3.5mm jack for connecting an IR Emitter (not
included).
⑧
DC 12V
DC barrel connector for connecting the included
AC power adaptor.
Tx Rx
LINKHDCP
12345678
Front Rear
PANEL DESCRIPTION
2
Usage Precautions
Make sure all components and accessories included before installation.
System should be installed in a clean environment with proper temperature and
humidity.
All of the power switches, plugs, sockets, and power cords should be insulated
and safe.
All devices should be connected before power on.
SYSTEM CONNECTION
3
Model
Spec
Transmitter (TX)
Receiver (RX)
Input
HDMI IN
HDBT IN
Output
HDBT OUT
HDMI OUT
Control
IR IN, IR OUT, RS232
IR IN, IR OUT, RS232
General
Maximum Video
Resolution
4K×2K@60Hz 4:2:0, including 1080p@60Hz
Transmission Mode
HDBaseT
Transmission Distance
1080p signal to 70m, 4K signal to 40m
Bandwidth
10.2Gbps
Video Standard
HDMI 1.4 with HDCP 2.2
Power Consumption
10 watts
Operation Temperature
-10℃~ +55℃
Storage Temperature
-25℃~ +70℃
Relative Humility
10%-90%
Power Supply
Input Power: 12VDC 1A or Power over Cable (PoC)
AC Adaptor Input Power: 100~240VAC, 50/60Hz
Dimension (W*H*D)
106mm x 16mm x 84mm
Net Weight (g)
250g
4
SPECIFICATION
Transmitter (TX)
Receiver (RX)
PANEL DRAWING
5
No image on display:
Ensure that the display device has been set to the correct input.
Ensure that the HDMI cables used for both the source/transmitter and the
receiver/display are properly connected and are working. Test the HDMI cables
directly from a source to display and ensure their operation.
Ensure that the CAT5e/CAT6a cable has not been damaged and that it has
been terminated correctly with T568B on both ends. A temporary length of
CAT5e/Cat6 can be used for testing to ensure that the devices are all
compatible and working properly.
Ensure proper grounding of the power supply.
Known issues with HDMI 1.2 source devices:
Older compatibility (HDMI 1.2) may result in HDBaseT transmission issues.
Please contact Technical Support of your director for a solution to these issues.
Color lose or poor picture quality:
Ensure that the HDMI cables used for both the source and transmitter and the
receiver and display are properly connected and are of good quality. Test the
HDMI cables directly from a source to display and ensure their picture quality.
Ensure proper grounding of the power supply.
If the static becomes stronger or picture quality becomes worse when
connecting the video connectors, this may be due to improper grounding.
Check the grounding and make sure all the components are properly grounded
to a common ground. Improper grounding may cause damage to the receiver.
Note: If your problem persists after following the above troubleshooting steps, seek
further help from authorized dealer or our technical support.
TROUBLESHOOTING & MAINTENANCE
6
Indice
Altri manuali J-Tech Digital Estensione
J-Tech Digital
J-Tech Digital JTECH-4K88-EX2 Manuale utente
J-Tech Digital
J-Tech Digital JTD-2987 Manuale utente
J-Tech Digital
J-Tech Digital JTD-190 Manuale utente
J-Tech Digital
J-Tech Digital JTD-2980 Manuale utente
J-Tech Digital
J-Tech Digital JTD-1651 Manuale utente
J-Tech Digital
J-Tech Digital JTECH-VW-4KPR Manuale utente
J-Tech Digital
J-Tech Digital JTD-2860 Manuale utente
J-Tech Digital
J-Tech Digital JTD-185 Manuale utente
J-Tech Digital
J-Tech Digital JTECH-AET1000 Manuale utente
J-Tech Digital
J-Tech Digital JTD-229 Manuale utente
J-Tech Digital
J-Tech Digital JTECH-EXBT460 Manuale utente
J-Tech Digital
J-Tech Digital JTECH-WEX-22 Manuale utente
J-Tech Digital
J-Tech Digital JTD-3033 Manuale utente
J-Tech Digital
J-Tech Digital JTECH-BE100 Manuale utente
J-Tech Digital
J-Tech Digital JTECH-EX230 Manuale utente
J-Tech Digital
J-Tech Digital JTD-1263 Manuale utente
J-Tech Digital
J-Tech Digital JTD-677 Manuale utente
J-Tech Digital
J-Tech Digital ProAV Series Manuale utente
J-Tech Digital
J-Tech Digital JTD-3023 Manuale utente
J-Tech Digital
J-Tech Digital ARC-HDEX40ARC Manuale utente
