J-TECH CommPass Manuale utente
1
Pager and Charger Guide
Part Number 321032B4
Premises Pager System®
CommPass®Pagers
GuestPass™Pagers
MediPass™Pagers
ShopperPass™Pagers
34
34
34
7
34
18
2
Introduction:
Congratulations on your purchase of the JTECH Paging System. Please take a
few minutes to review this manual prior to installing and operating your system.
Please inspect the System upon receipt. If the contents appear to be damaged,
notify the shipper immediately to file a claim and notify JTECH Customer Care.
If any component is missing, please contact JTECH Customer Care.
If you have any questions or need assistance, please call JTECH Customer
Care at 800-321-6221 or 561-997-0772, option 6.
CommPass Pager System Components:
Pager Certifications:
FCC statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Caution:
Changes or modifications not expressly approved by the part responsible
for compliance could void the user's authority to operate the equipment.
RSS-Gen:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. Le présent
appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
AC Power
Cord
Jumpers
Pager Certifications Components Introduction
CommPass
Pager with
Standard Insert
3
2.4 A or
7.3A (Optional)
Power Adapter
Charger with
Key Attached
Mounting
3
Pager Dimensions/Weight:
LxWxH 5.4x 2.3x 0.9” (137x58x23mm)
Weight 3.5oz (99gm)
Charger Dimensions/Weight:
LxWxH 7.3x 6.9x 13.1” (184x176x333mm)
Weight (Empty) 6.6lbs (3.0Kg)
Weight (With 20 Pagers) 11.0lbs (5.0Kg)
Multiple Chargers:
A single Charger can hold up to 20 Pagers.
Combine two or three Chargers using the optional Jumpers and 7.3A
Power Adapter.
Mounting Chargers:
Chargers can be wall or counter top mounted using the supplied Mounting
Plate.
Wood screws are include for table or shelf mounting.
If mounted to a shelf or table, the four rubber feet on the bottom of the
Charger must be removed.
Wall anchor hardware is user supplied.
3
W
L
H
Mounting Chargers Multiple Chargers Pager and Charger Dimensions/Weight
W
H
L
4
Connecting Power:
1. Insert the Power Adapter plug into the jack at the
bottom of the Charger.
2. Connect the Power Adapter to the Power Cord.
3. Plug the Power Cord into a 120VAC outlet.
4. The green LED on the Charger will light (ON).
5. Once the Charger is ON, the Pagers can be inserted.
Power
Adapter
Plug
Charger
Jack
120VAC
Outlet
Charging
Rack
Adapter
Power Cord
Connecting Power to the Charger
5
Charging and Storing Pagers Charging Pagers
Charging Pagers:
Pagers are turned OFF for shipment from JTECH.
When first received, Pagers are to be charged for a minimum of 3 hours
prior to use.
This first charge will also turn ON the
Pagers.
To charge:
1. Insert Pagers into the empty Charger
locations.
2. Once in the powered (ON) Charger,
each Pager’s LED will light:
3. The LED color indicates charging
condition.
Flashing yellow light = Battery
charge very low. Charge
needed. Do not use the Pager.
Solid yellow light = Charge
Needed.
Solid green light = OK to use.
The charging system is two stage, with a fast initial charge and then a final
maintenance charge.
Pagers in use and returned to the Charger within 24 hours will fully charge
within three hours.
If not returned within 24 hours, charging time of up to eight hours may be
required to fully charge batteries.
Charging and Storing Pagers:
To maintain maximum battery capacity, store Pagers
in the powered (ON) Charger.
If Pagers are left uncharged for more than 4 days, it is
recommended to disconnect the batteries until their
next use. See “Replacing the Battery” on page 10
for instructions.
If left uncharged for extended periods of time, Pager
batteries can damage beyond repair and will need to be
replaced.
When charged and stored properly, a battery life of 18-24 months can be
expected before replacement is suggested.
1
0
9
8
7
6
5
4
3
2
1
20
19
18
1
16
15
14
13
12
11
1
9
8
7
6
5
4
3
2
1
2
1
1
1
1
1
1
1
1
1
6
Paging Using a Desktop Transmitter:
1. Remove the Pager you wish to page from the
Charger.
2. The Pager will flash and vibrate to confirm it is
ready for use.
3. The Pager LED in the front of the Pager will
continue to flash every 3-4 seconds to confirm the
Pager is ON and ready to accept a page.
4. Enter the number of the Pager you wish to page on
the Transmitter or Remote Keypad.
5. Press # to send the page. Press the # or SEND
button if using an IntelFlex Desktop Transmitter.
6. The XMIT light on the Transmitter will turn ON,
confirming the page is being sent. If using a
Remote Keypad, the Keypad XMIT light does not
ON.
7. The Pager will vibrate, flash tone or
speak as required.
8. See “Enter Pager #” Menu Functions in your
Transmitter manual for more information.
Paging Using a Desktop Transmitter
3
3
3
3
3
7
16
15
6
5
14
3
3
3
7
7
16
15
6
5
14
5
Paging Using a 8205 or 8214 SmartAlert with RS232
and Telephone Transmitter Paging using the
Telephone:
1. Remove the Pager you wish to page from the Charger.
2. The Pager will flash and vibrate to confirm it is
ready for use.
3. The Pager charge LED will continue to flash, confirming
it is ready to receive a page.
4. Pick up the telephone and listen for the dial tone.
5. Dial the telephone number that has been assigned to
the Transmitter.
6. Listen for a beep from the telephone that confirms the
Transmitter is ready.
7. Within 8-10 seconds, use the telephone keypad:
a. Enter the Pager number (up to 4 digits).
b. Press the # key to send the page.
8. A beep will be heard on the telephone that confirms
the message was sent.
9. Hang up the telephone.
10. The Pager will receive a single, one second
vibration (factory setting).
11. See Paging instructions in your Transmitter manual
for more information.
Paging Using a 8205 or 8214 SmartAlert with RS232 and Telephone Transmitter
3
3
3
3
3
3
3
3
8
Replace Inserts:
1. Insert the KEY into the slots on the end of the Pager,
until the Clear Plastic Cover unlocks.
2. Remove the Clear Plastic Cover and Insert.
3. Replace the Insert and “snap” the Clear Plastic Cover
back into place.
5
34
34
5
34
34
34
Replacing Pager Inserts
9
Blank Inserts:
Blank Promotional Sheets can be ordered from JTECH as needed.
Sheets contain eight Inserts per sheet and perforated for removal.
Sheets are white in color and can be printed on using a standard
printer.
Custom Inserts can also be professionally printed (call your JTECH
sales representative for more details).
Insert Dimensions:
8 1/2”
(215.9m
11” (279.4
0.12”R
(3mm R)
1.25”R Typ.
(31.7mm R)
15.0”RTyp.
3.90” (99.1mm)
Cut Out
Material Thickness 0.02” (0.5mm) Max
0.30” (7.6mm)
C
L
1.05”
(26.7mm)
0.70”
(17.8mm)
0.12” (3.05m)
1.40” (35.6mm)
1.20”
(30.5mm)
Insert Dimensions Blank Inserts
10
Replacing the Battery:
Batteries that no longer charge properly or have a reduced
operating time can be replaced by the user.
Replacement battery packs can be ordered from JTECH.
To replace:
1. Insert the Key into the slots on the end of the
Pager until the Clear Plastic Cover unlocks.
2. Remove the Clear Plastic Cover and
Insert.
3. Insert the Key into the space on the left side of the
battery compartment and carefully pry the battery out.
Replacing the Battery
5
34
6
6
5
34
6
6
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali J-TECH Cercapersone
J-TECH
J-TECH ServerCall J1703 Manuale utente
J-TECH
J-TECH GuestCall CommPass J1701 Manuale utente
J-TECH
J-TECH RT-760GER Manuale utente
J-TECH
J-TECH ServerCall J1703 Manuale utente
J-TECH
J-TECH ServerCall J1703 Manuale utente
J-TECH
J-TECH GuestCall IQ J1705 Manuale utente
J-TECH
J-TECH GuestCall Coaster J1707 Manuale utente
J-TECH
J-TECH QuikCall 321045B5 Manuale utente
J-TECH
J-TECH GuestCall IQ Manuale utente
J-TECH
J-TECH Premises Istruzioni per il montaggio
