Jacuzzi JAG Manuale utente

OWNER’S MANUAL

WARNING

FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product

must be serviced by a pool technician who is licensed and qualified in pool equipment by the jurisdiction in which the product

will be installed where such state or local requirements exist. In the event no such state or local requirement exists, the

maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the

instructions in this manual can be followed exactly. Improper installation and/or operation may void the warranty.

JAG

Robotic Cleaner

TYPE: SSDP37--

2JACUZZI®JAG ROBOTIC CLEANER

FCC STATEMENT

This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modications not expressly approved by the part responsible for compliance could void the user's authority to

operate the equipment.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference including interference that may cause undesired operation of the device.

THANK YOU FOR PURCHASING THIS ROBOTIC POOL CLEANER.

YOUR ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY INSTALLED AND TO

PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW CLEANER, PLEASE DO THE

FOLLOWING:

1) Record your purchase information on the spaces provided below.

2) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt service, should it be required. If service is required, please

contact your original dealer. If the original dealer does not perform warranty service, please call our Technical Support

department at 1-800-822-7933.

RECORD YOUR CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on robot- head)

City State/Province Zip/Postal Code

OWNER'S MANUAL

TABLE OF CONTENTS

Section 1. Important Safety Instructions........ 4

Section 2. Cleaner specications .................... 5

2.1 General Specications .................................................................5

Section 3. Connect to Power............................ 5

Section 4. Install the Cleaner ........................... 6

4.1 Submerge in the Pool ..................................................................6

4.2 Start / Stop Cleaning....................................................................7

4.3 Optimal Patterning/Cable Tangling ........................................8

4.4 Remove from Pool........................................................................8

4.5 Remove Debris...............................................................................8

4.6 Store the Cleaner When Not in Use...................................9

Section 5. Maintenance Tips ........................... 10

Section 6. Spare Parts ..................................... 11

Section 7. Troubleshooting ............................. 11

4JACUZZI®JAG ROBOTIC CLEANER

SECTION 1. IMPORTANT SAFETY INSTRUCTIONS

Please read through the entire manual before installing your new robotic pool cleaner. The cleaner must be installed

and operated as specied.

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or

death.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle should

be provided by a qualied installer and should be tested on a routine basis. To test the GFCI, push the test

button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to

operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button

being pushed, a ground current is owing, indicating the possibility of an electric shock. Do not use this product.

Disconnect the cleaner and have the problem corrected by a qualied service representative before using.

• Per the United States National Electrical Code

(NEC

), keep the control box at least ve (5) feet from the

edge of the (pool/spa) water. In Canada, the Canadian Electrical Code (CEC) requires a minimum distance of

3m (10ft.) to be maintained between the pool edge and the control box. Never submerge the control box.

• Do not enter pool while the cleaner is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers and

other equipment.

• To reduce the risk of electrical shock, do not use the robotic cleaner or control box if the cord is worn or

damaged. Contact Technical Support immediately for proper servicing and replacement of the damaged cord.

• Double insulation—For continued protection against possible electric shock, use only identical replacement

parts when servicing. Do not attempt repair of the robotic cleaner, control box, power cord, or oating cable.

• NEVER OPEN CONTROL UNIT.

• DO NOT USE AN EXTENSION CORD TO CONNECT THE UNIT TO ELECTRIC SUPPLY; PROVIDE A

PROPERLY LOCATED GFCI RECEPTACLE. THE CONTROL BOX SHOULD BE PLUGGED INTO THE GFCI

RECEPTACLE BOX.

PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of your

pool’s operational system.

OWNER'S MANUAL

SAVE THESE INSTRUCTIONS

SECTION 2. CLEANER

SPECIFICATIONS

2.1 GENERAL SPECIFICATIONS

The general specications for the cleaner are as follows:

Control box supply voltage 100-240 VAC, 50-60 Hz

Output voltage 30 V DC

Installed load 100 W max

When unpacking the cleaner and its components:

• Check cleaner and components for damage during

transport.

• If there are any missing parts or damage, contact

Technical Support at 1-800-822-7933.

SECTION 3. CONNECT

TOPOWER

WARNING

Failure to comply with the following warnings can result in

permanent injury, electrocution or drowning.

PREVENT ELECTRICAL SHOCK

• U.S.: Per NEC®requirements, keep the control unit

at least ve (5) ft. (1.5 m) from the edge of the pool.

CANADA: Per CEC requirements, keep the control unit

at least three (3) m (10 ft.) from the edge of the pool.

• Only connect the control unit to a receptacle protected

by a ground fault circuit interrupter (GFCI). Contact

a certied electrician if you cannot verify that the

receptacle is protected by a GFCI.

• Do not use an extension cord to connect the control unit.

• Do not allow anyone to swim while the cleaner is in

the pool.

• The control unit is not waterproof. In order to prevent

electrocution, never submerge the control unit or leave

exposed to inclement weather.

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal

injury.

• The cleaner must be installed and operated as specied.

• Clean out the debris from the cleaner after each use.

• Do not use the product in your pool if the water temperature is above 95°F (35°C) or below 55°F (13°C).

USE OF THE ROBOTIC CLEANER IN A VINYL LINER POOL

• Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by

objects coming into contact with the vinyl surface, including pool brushes, pool toys, oats, fountains, chlorine

dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded simply

by rubbing the surface with a pool brush. Ink from the pattern can also rub o during the installation process

or when it comes into contact with objects in the pool. We are not responsible for, and the Limited Warranty

does not cover, pattern removal, abrasion or markings on vinyl liners.

6JACUZZI®JAG ROBOTIC CLEANER

1. Plug power supply into a GFCI outlet (Ground

Fault Circuit Interrupter) (Figure 1). Power Supply

must be 5ft. from the pool's edge.

Figure 1. Plug into Power Supply

2. Straighten the oating cable. Lift the ap on

the power supply and plug in the power cable

(Figure2).

Figure 2. Connect the Power Cable

SECTION 4. INSTALL THE

CLEANER

CAUTION

To prevent damage to the cleaner, be sure to adhere to

the following guidelines:

• Remove the cleaner from the pool after the cleaning

cycle is completed.

• Store cleaner out of direct sunlight out of direct

sunlight or inclement weather.

• Never lift the cleaner out of the pool by the oating

cable.

• Take additional care when lifting the cleaner out of the

pool. It becomes heavier when lled with water.

• Always remove the cleaner from the pool before super

chlorinating or adding acid.

• Do not handle cleaner while it is in operation.

IMPORTANT

• Always make sure the cleaner head is fully

submerged before you begin operation.

• Clean out debris after each cleaning cycle.

• Do not leave your cleaner in the pool on a

permanent basis.

• At the end of each cycle, remove the cleaner from

the pool.

• Start at the cleaner head and untangle any coils in

the cable before storing the cleaner.

4.1 SUBMERGE IN THE POOL

1. With the control box plugged into a GFCI outlet,

spread the oating cable across the pool deck

until you reach the middle of the pool length.

NOTE: For optimal patterning and reduced tangling, the

floating cable should enter the water near the middle

of the pool length.

OWNER'S MANUAL

12 ft / 4 m

Midpoint of the long side of pool

Figure 3. Pool Entry Point for Optimal Patterning

2. Submerge cleaner vertically and turn upside

down until the bubbles stop to remove any air

trapped inside

(Figure 4)

3. When the bubbles stop, allow the cleaner to sink

to the bottom of the pool.

Figure 4. Submerge and Remove Trapped Air

4. Verify the cleaner is sitting right-side up on the

bottom of the pool. Remove additional air if the

cleaner is still oating.

5. Spread all of the oating cable carefully in the

pool, ensuring there are no kinks or coils.

Useonly as much cable as you need to reach the

farthest wall. This can help prevent cable tangling

(Figure 5).

Figure 5. Spread Floating Cable to Prevent

Tangling

4.2 START / STOP CLEANING

1. Press On/O button to begin or interrupt cleaner

operation (Figure 6).

ON / OFF

Figure 6. Begin Cleaning

2. Press SELECT button to choose between SMALL

POOL and LARGE POOL. Cleaning duration for

a small pool is 1 hour; for a large pool, duration is

2 hours (Figure 7).

3. Cleaner will begin to move.

= 1 Hour Shut-off

= 2 Hour Shut-off

Figure 7. Select Pool Size and Duration

8JACUZZI®JAG ROBOTIC CLEANER

4.3 OPTIMAL PATTERNING/CABLE

TANGLING

It is recommended to alternate the angle and direction

of the cleaning path every cleaning cycle to ensure the

cleaner is covering the whole pool, as well as prevent

cable tangling.

1. Turn the cleaner upside down. Locate the wheel

pins on the axle: one adjustable pin; one xed pin.

(Figure 8)

2. Reverse the positions of adjustable and xed

wheel pins (Figure 9).

Figure 8. Change Wheel Turning Direction

Axle Position

Fixed

Adjustable

Figure 9. Alternate Wheel Axle Pins

4.4 REMOVE FROM POOL

1. Gently pull the oating cable to bring the cleaner

within arm's reach (Figure 10).

Figure 10. Bring Cleaner to Pool's Edge

2. Gently pull the cleaner up to the waterline

(Figure11).

Figure 11. Pull Cleaner to Waterline

3. Use the handle to lift the cleaner from the water

(Figure 12). Never lift the cleaner out of the pool

by the oating cable.

Figure 12. Lift Cleaner Using the Handle

4.5 REMOVE DEBRIS

For best performance, remove debris after every

cleaning cycle.

WARNING

To avoid electric shock and other hazards which could

result in permanent injury or death, disconnect (unplug)

the cleaner from the power source before performing

any cleaning and maintenance.

1. Unplug power to the cleaner at the control unit.

Unplug the control unit from the power source.

2. Push side tabs down and outward to release the

cleaner lid (Figure 13).

OWNER'S MANUAL

Figure 13. Remove the Cover

3. Pull gently on the elastic band around the suction

ports to release the lter bag (Figure 14).

Figure 14. Release the Elastic Band around Bag

4. Pull tabs to unfasten and turn the bag inside out

for thorough cleaning (Figure 15).

Figure 15. Turn Bag Inside Out

5. Using a hose with clean water, rinse the lter bag

to remove all debris (Figure 16).

Figure 16. Rinse

6. Replace back into the cleaner body and replace

the cover.

7. Store the cleaner out of direct sunlight for next use.

4.6 STORE THE CLEANER WHEN NOT

IN USE

Do not leave the cleaner in the pool when not in

use. The cleaner should be cleaned regularly using

slightly soapy clean water. Do not use solvents such

as trichlorethylene or its equivalent. Rinse the cleaner

generously using clean water. Do not let your cleaner

dry in direct sunlight near the pool.

1. Disconnect cleaner from the power source.

2. Start at the cleaner head, remove all coils and

tangles from the oating cable. Lay the cable in the

sun to loosen any tangling memory (Figure 17).

3. Disconnect the cable from the control unit.

Figure 17. Untangle the Floating Cable

4. Loosely coil the oating cable starting at the

cleaner and moving toward the connection point

at control unit.

5. Store the cleaner and power supply in a dry/

shaded area.

6. For extended periods, such as winter months,

store the cleaner in a box to keep motors, plastics

and seals protected (make sure the cleaner is dry

before storing) (Figure 18).

10 JACUZZI®JAG ROBOTIC CLEANER

Figure 18. Long Term Storage for Extended Period

SECTION 5. MAINTENANCE

TIPS

Regular maintenance is recommended to extend the life

of your cleaner.

WARNING

To avoid electric shock and other hazards which could

result in permanent injury or death, disconnect (unplug)

the cleaner from the power source before performing

any cleaning and maintenance.

1. Avoid dropping the unit or the power supply.

Dropping the cleaner may cause serious damage.

2. Clean the lter bags regularly.

Regular cleaning prevents clogging and keeps

recirculated water cleaner.

3. Adjust wheel direction after every cleaning

cycle.

Adjusting wheel direction ensures your cleaner

reaches all areas of the pool and prevents cable

tangling.

4. Rinse the cleaner with fresh water.

Rinsing the outside and the inside of the cleaner

removes chlorinated pool water and protects

internal components.

5. Store in a cool, dry location when not in use.

Coil the cable under the cleaner and store in a dry/

shaded area. Store in a dry box for longer periods.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Jacuzzi Aspirapolvere

Jacuzzi

Jacuzzi JPV100 Manuale utente

Manuali Aspirapolvere popolari di altre marche

Bissell

Bissell LittleGreen Proheat 1425 Series Manuale utente

Panasonic

Panasonic MC-YL637S147-AE Manuale utente

NEFF

NEFF N17XH10 0 Series Manuale utente

LG A9 Series Manuale utente

Oreck

Oreck Cordless Captura BK51700 Series Manuale utente

Kogan

Kogan KAVACROBVWA Manuale utente

Kränzle

Kränzle VENTOS 50 ID Guida utente

EVVO

EVVO Ai35 Manuale utente

DeWalt

DeWalt DWH200D Manuale utente

Pontec

Pontec Pondomatic Vacuum Cleaner Manuale utente

Cleanmaxx

Cleanmaxx PC-P007E Manuale utente

Exido

Exido 240-114 Manuale utente

RIDGID

RIDGID WD1685AU0 Manuale utente

Ezviz

Ezviz RE4P Manuale utente

STG global

STG global TANVAC HDV3000 Manuale utente

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuale utente

Factory

Factory M3340 Manuale utente

Shop-Vac

Shop-Vac VN92 SERIES Manuale utente