JBL CBT1000 Manuale utente
CBT1000 and CBT1000E
Bracket Installation Guide
Rev C
CBT1000 CBT1000E
Hardware Included with CBT1000:
Tools Required:
M6 Hex Wrench
#2 Phillips Head Screwdriver
Note: When setting system for UP tilting, the UPPER and LOWER
parts get reversed on the cabinet -- see instructions.
M6 x 115 mm
PAN HEADS
WALL
BRACKETS
SPEAKER
BRACKETS
ARM
LINK
SWIVEL
BRACKETS
←
M6 x 125 mm
PAN HEADS
M6 x 20 mm
SOCKET HEADS
M8 x 20 mm
PAN HEADS
M6
FLAT WASHERS
M6 SPLIT
LOCK WASHERS
M6 RUBBER
WASHERS
M8
FLAT WASHERS
M8 SPLIT
LOCK WASHERS
M6
CAP NUTS
4 Bracket Parts for UPPER
Mounting Position on
Cabinet (when set for 0° or
for down-tilting)
3 Bracket Parts for LOWER
Mounting Position on
Cabinet (when set for 0° or
for down-tilting)
←
Hardware Included with CBT1000E:
Tools Required:
#2 Phillips Head Screwdriver
M8 x 20 mm PAN HEADS
M8 FLAT WASHERS
M8 SPLIT LOCK WASHERS
2
Instructions for CBT 1000 Alone (without 1000E):
The BRACKET ASSEMBLY consists of 2 pieces of SPEAKER BRACKETS (the parts that mount on the
speaker), 2 pieces of WALL BRACKETS (the parts that mount on the wall), 2 pcs of SWIVEL BRACKETS
(which get added to the SPEAKER BRACKETS if utilized for horizontal swivel/pan aiming capability), and an
ARM LINK (which is utilized for the larger tilt angles).
1) RUN WIRING -- Run the wiring from the power amplier to the location desired for mounting the JBL
CBT Loudspeakers. Note: Connect wire to speaker terminals at a point in the installation process when
convenient for your installation circumstances.
2) ATTACHING WALL BRACKET TO WALL -- Using a level to ensure that the WALL BRACKET is straight,
secure the WALL BRACKET to the wall. Be sure to use the appropriate wall anchors for attaching the
bracket. Use as many of the screw holes as possible for maximum integrity and safety.
CAUTION: Installation must be done by
qualied persons using safe rigging standards.
The installer is responsible for proper selection and use of
mounting hardware to properly and safely wall-mount the
speakers.
Hardware attaching WALL BRACKET to wall is not included.
Utilize proper hardware for particular wall structure.
Spacing needed between upper and lower
WALL BRACKET parts with CBT1000 depends on
whether speaker will be set with down-tilt or up-tilt.
Spacing:
181 mm (7-1/8”) for Down-Tilt
197 mm (7-3/4”) for Up-Tilt
3
(Drawings show upper
and lower bracket
orientation as set for
down-tilt or 0°. Wall
brackets to be reversed
in location and ipped for
up-tilt applications (see
further instructions).
3) ATTACH SPEAKER SIDE OF BRACKET TO SPEAKER
Mount the SPEAKER BRACKET (2 pcs) to the speaker with the provided M8 x20 mm pan-head bolts, in
the locations shown and in the orientation shown in the diagram below.
Option 3a) CBT 1000 with No Swivel (for Down-Tilt Capability [or 0° tilt] and No Horizontal Swivel/Pan).
M8
FLAT WASHER
M8 SPLIT
LOCK WASHER
M8 x 20 mm
PAN HEAD
BOLT
8 PLACES:
Down-tilt range 0° to -15°
4
Option 3b) CBT 1000 with Up-Tilt Capability -- No Horizontal Swivel/Pan
M8
FLAT WASHER
M8 x 20 mm
PAN HEAD
BOLT
M8 SPLIT
LOCK WASHER
8 PLACES:
Up-tilt range 0° to +15°
5
Option 3c) CBT1000 Mounting with Down-Tilt Capability and SWIVEL BRACKET
(for Horizontal Swivel/Pan aiming capability)
M6 Hex Wrench
M6 x 20 mm
SOCKET HEAD BOLT
M6 SPLIT
LOCK WASHERS
M6 FLAT WASHERS
M8
FLAT WASHER
M8 SPLIT
LOCK WASHER
M8 x 20 mm
PAN HEAD
BOLT
8 PLACES:
8 PLACES:
Down-tilt range 0° to -15°
6
Option 3d) CBT1000 Mounting with Up-Tilt Capability and SWIVEL BRACKET
(for Horizontal Swivel/Pan aiming capability)
M6 Hex Wrench
M6 x 20 mm
SOCKET HEAD BOLT
M6 SPLIT
LOCK WASHERS
M6 FLAT WASHERS
M8
FLAT WASHER
M8 SPLIT
LOCK WASHER M8 x 20 mm
PAN HEAD
BOLT
8 PLACES:
8 PLACES:
Up-tilt range 0° to +15°
7
For Options 3c and 3d (congurations that include the SWIVEL BRACKET), place RUBBER
WASHERS as shown when using SWIVEL BRACKET:
RUBBER WASHERS to be placed
between SWIVEL BRACKET and
SPEAKER BRACKET
8
4) Jump to page 15 for CBT 1000 tilt angling instructions.
Instructions for CBT 1000+1000E System:
The BRACKET ASSEMBLY consists of 2 pieces of SPEAKER BRACKETS (the parts that mount on the
speaker), 2 pieces of WALL BRACKETS (the parts that mount on the wall), 2 pcs of SWIVEL BRACKETS
(which get added to the SPEAKER BRACKETS if utilized for horizontal swivel/pan aiming capability), and an
ARM LINK (which is utilized for the larger tilt angles).
1) RUN WIRING -- Run the wiring from the power amplier to the location desired for mounting the JBL
CBT Loudspeakers. Note: Connect wire to speaker terminals at a point in the installation process when
convenient for your installation circumstances.
2) ATTACHING WALL BRACKET TO WALL -- Using a level to ensure that the WALL BRACKET is straight,
secure the WALL BRACKET to the wall. Be sure to use the appropriate wall anchors for attaching the
bracket. Use as many of the screw holes as possible for maximum integrity and safety.
CAUTION: Installation must be done by qualied persons
using safe rigging standards.
The installer is responsible for proper selection and use of mounting hardware
to properly and safely wall-mount the speakers.
Hardware attaching WALL BRACKET to wall is not
included. Utilize proper hardware for particular wall
structure.
Spacing needed between upper and lower
WALL BRACKET parts with CBT1000 and
CBT1000E depends on whether speaker will be set
with down-tilt or up-tilt
Spacing:
1200 mm (47-1/4”) for Down-Tilt
1216 mm (47-7/8”) for Up-Tilt
9
(Drawings show upper
and lower bracket
orientation as set for
down-tilt or 0°. Wall
brackets to be reversed
in location and ipped for
up-tilt applications (see
further instructions).
3) ATTACHING COUPLER PLATE -- Connect the CBT 1000 and CBT 1000E together by attaching
COUPLER PLATE to bottom four (4) insert points of the CBT 1000 and to top four (4) insert points of
CBT 1000E using 8 pcs M8 x 20 PAN-HEAD PHILLIPS BOLTS with LOCK WASHERS and FLAT
WASHERS. Tighten.
IMPORTANT: WHEN THE CBT 1000E IS LOCATED ON THE TOP VERSUS ON THE BOTTOM
The diagram below shows the COUPLER PLATE attachment method for when the CBT 1000 is on
the top and the CBT 1000E on the bottom. For utilizing with the CBT 1000E on top and the CBT
1000 on the bottom, the depth of the cabinets are different at the junction between them, so it is
necessary to use the optional MTC-CBT-OS3 Offset Bracket (which is part of the CBT1K-ACC1
kit). See Appendix A for attaching together in this orientation utilizing the MTC-CBT-OS3 bracket.
M8 x 20 mm
PAN HEAD
BOLT
M8 SPLIT
LOCK WASHER
M8
FLAT WASHER
8 PLACES:
Hint: One strategy for orienting speakers for
attaching the COUPLER PLATE is to place
both speakers on a non-scratching oor
surface on their sides.
10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali JBL Supporto TV
