JCM Technologies ACTIVA Manuale utente
ACTIVA
Introduction 4
General data 5
Chassis attachment 5
Connections terminals 6
Installation 7
Regulatory Data 8
EU Declaration of conformity 8
Introducción 9
Datos técnicos 10
Fijación de la caja 10
Bornes de conexión 11
Instalación 12
Datos reglamentarios 13
Declaración de conformidad UE 13
Introduction 14
Données techniques 15
Fixation du boîtier 15
Bornes de connexion 16
Installation 17
Données réglementaires 18
Déclaration de conformité UE 18
Einführung 19
Technische Daten 20
Einbau 20
Anschlußklemme 21
Installation 22
Daten 23
jcmtechnologies
2
Introduction
ACTIVA antenna (Dynamic code):
This external antenna is very usefull for facilities where the reception of the built-in
antenna is not good (for example: long distances, access ramps or underground gar-
ages, large metal surfaces, ...). In addition to its antenna functions, it also contains
the entire receiving piece and enables different receiving points of a facility to be
improved or extended (up to a maximum of 200 meters). As the decoder unit is
always located inside the building, it makes the facility completely invulnerable.
1AERIAL CONNECTOR 2RADIO CARD
3RECEIVER UNIT / CONNECTION TERMINAL / POWER SUPPLY
CONNECTION / EXIT SIGNAL
jcmtechnologies
4
General data
Parameter Value
Frequency 433.92 MHz
Antenna Built-in adjustable
Certificate Meets European std I-ETS 300 220
Power 12 V.DC
Sensitivity > 100 dBm
Power consumptionat
work / at rest 7 mA / 20 mA
Working temperature 0 - 70°C
Waterlight IP 44
Dimensions 112 x 72 x 51 mm
Chassis attachment
The antenna comprises four different pieces: a rear cover, circuit, front curved cover
and adjustable antenna.
1. Attach the rear of the box to the wall using the plugs and screws supplied.
2. Attach the circuit to the rear of the box.
3. Pass the cables through the bottom of the microreceiver.
4. Slide the front of the ACTIVA antenna over the track in the rear cover.
5. Screw the antenna to the top of the chassis.
jcmtechnologies
5
Connections terminals
+ Alimentación, 12 V
-Supply voltage,
ground
S Coded signal
Disconnect the power before handling.
•Connect the three terminals to match the settings on the receiver unit installed
inside.
•To connect the ACTIVA antenna and the receiver unit located inside the facility, use
a 3-wire twisted sheathed cable.
In the case of using standard 4-strand cable, the correct connection is as follows:
Cable connection enlarged
For extreme cases of more than 200 metres distance, the cable
can be extended some metres further by placing a 1K resistance
between the "S" and "-" terminals, always depending on the inter-
ference that may arise in the installation itself.
jcmtechnologies
6
Installation
Place the antenna outdoors to ensure optimal reception. Since the codes are stored in
the decoder and not in the antenna, this does not pose any possible breach of secur-
ity.
•It disposes of an adjustable antenna.
•Do not place the ACTIVA antenna less than five meters from any other receiver
and/or ACTIVA antenna.
Table showing the cable section to use, according to the distance between the
receiver and the operative antenna:
From 1 to 3 operative antennae connected to the same receiver
Cable section Maximum distance
0,5 mm2 200 m
From 4 to 7 operative antennae connected to the same receiver
1 mm2 200 m
Avoid placing near metal objects. If unavoidable, tilt
the antenna 90°C to position it perpendicular to these
objects.
jcmtechnologies
7
Regulatory Data
EU Declaration of conformity
The manufacturer JCM TECHNOLOGIES, S.A. declares that the product ACTIVA
complies with the relevant fundamental requirements of the RED Directive
2014/53/EU and of the RoHS Directive 2011/65/EU.
See website https://www.jcm-tech.com/declarations/
JCM TECHNOLOGIES, SA
C/COSTA D'EN PARATGE, 6B
08500 VIC (BARCELONA)
SPAIN
jcmtechnologies
8
UM_3200070_ACTIVA_5ID_Rev03
Introducción
Antena ACTIVA (Dynamic code):
Este equipo permite cubrir la necesidad de una recepción exterior directa en los casos
en que la del receptor o cuadro de maniobra ubicados en el interior, se vea obs-
taculizada por grandes distancias, rampas de acceso a garajes subterráneos, gran-
des superficies metálicas, etc. Su reducido tamaño y fácil instalación lo convierten en
un equipo de recepción idóneo.
La Antena ACTIVA no contiene la parte de descodificación de códigos en su circuito y
es el receptor interno quien determina si la señal recibida a través del cable es la
correcta o no. Esta configuración garantiza la imposibilidad de sabotajes o mani-
pulaciones indeseadas.
1CONECTOR ANTENA 2TARJETA DE RADIO
3BORNE CONEXIÓN / EQUIPORECEPTOR / ENTRADA
ALIMENTACIÓN /SALIDA SEÑAL
jcmtechnologies
9
Datos técnicos
Parámetro Valor
Frecuencia 433,92 MHz
Alimentación 12 V D.C.
Número máximo de antenas
conectables 3 en paralelo
Antena Incorporada orientable
Certificación s/norma europea I-ETS 300 220
Estanqueidad IP 44
Sensibilidad mejor que -100 dBm
Consumo reposo/ fun-
cionamiento 7 mA / 20mA
Temperatura fun-
cionamiento 0 a 70°C
Dimensiones 112 x 72 x 51 mm
Fijación de la caja
La antena ACTIVA está compuesta por 4 piezas distintas: una tapa posterior, un cir-
cuito, una tapa frontal de forma curvada y una antena orientable.
1. Fijar la parte posterior de la caja en la pared utilizando los tornillos y tacos sumi-
nistrados.
2. Fijar el circuito a esta parte posterior.
3. Pasar los cables por la parte inferior de la antena ACTIVA.
4. Deslizar el frontal por la guía de la tapa posterior.
5. Roscar la antena en la parte superior de la caja.
jcmtechnologies
10
Indice
Lingue:
Altri manuali JCM Technologies Antenna
Manuali Antenna popolari di altre marche
Alfa Network
Alfa Network APA-L01 Manuale utente
Naval
Naval PR-422CA Manuale utente
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manuale utente
TERK Technologies
TERK Technologies TV44 Manuale utente
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manuale utente
HP
HP J8999A Manuale utente
