JDS Stargate LCD-96M Manuale utente

LCD MULTI-MENU KEYPAD

LCD-96M

USER MANUAL

INT

ERACTIVE AUTOMATION SYSTEM

12200 Thatcher Court Poway, CA 92064 U.S.A.

TEL 858-486-8787 FAX 858-486-8789

EMAIL [email protected]

www.jdstechnologies.com

“The Home of Automation”

REV 1.1

Contents ....................................................................................... 2

Overview ....................................................................................... 3

Hole Cut-out Template ................................................................... 4

Installing the LCD-96M enclosure .................................................... 5

Connection using Hub (Homerun wiring) .......................................... 6

Connection using Daisy-Chain wiring .............................................. 7

Setup ........................................................................................ 8

PROGRAMMING AND OPERATION

Programming and Operation Introduction ........................... 9-10

Using Bitmapped Graphics ............................................................. 11

Custom Actions

Then Actions ....................................................................... 12

X-10 Two-Way ...................................................................... 13

Pre-Defined Menus

Thermostat ..................................................................................... 14

Voice Mail ...................................................................................... 15

Time Label ..................................................................................... 16

Variable ........................................................................................ 17

Caller ID ........................................................................................ 18

DigitPad ........................................................................................ 19

TelePad ........................................................................................ 20

Time Display ................................................................................. 21

Then LCD Keypad Actions

Then Keypad Actions............................................................... 22

LED Actions ....................................................................... 23

Backlight Actions ....................................................................... 24

Writing Text ................................................................................... 25

Changing Text ................................................................................ 26

Inverting Text ................................................................................ 27

Glossary ........................................................................................ 28

Bitmap Library ....................................................................... 28

Specifications .................................................................................. 28

Troubleshooting .............................................................................. 29

CONTENTS

OVERVIEW

The LCD-96M is a versatile, easy-to-use, menu-driven keypad that allows control of lighting, heating/cooling, security, home theater,

audio/video, pool/spa, irrigation, voice mail, and other systems connected to Stargate. Up to 96 interactive menu screens canbe created

anddownloadedtotheLCD-96Mbytheuser/installerwiththeincludedEventManagersoftware. Eachmenuline(upto8permenu)can

consist of text (up to 10 letters across) or bitmapped graphics (.bmp format, 64 x 16 pixels).

8 Dual-Position Rocker Buttons, located to the right of the menu display, can be individually programmed to perform different functions

depending on the menu selected. The Left and Right side of each button can be programmed independently (such as left = off, right = on)

orperformthe same function (such as go to Main menu). Programmable functions include: Navigational functions (go to menu, previous

menu), Then Actions (X-10, IR, Relay, Macro, VoiceMail, Flag, Variable, Audio Path) and Predefined Menus (Thermostat, VoiceMail,

TimeLabel, Variable, Caller ID, DigitPad, TelePad, Time Display). A special Two-Way X-10 feature allows any X-10 address to be

assigned to a rocker button. Pressing once on the right or left side of the button turns the X-10 device On or Off. Holding down the right

or left side of the button Brightens or Dims. On/Off status is indicated by a normal (Off) or reversed (On) background on the associated

menu line for easy viewing, even from a distance.

IndividualmenuscreensorcompletesetupscanbedownloadedtokeypadsviathesharedRS-485connectionorstoredondiskastemplates

andlater loaded tokeypads as needed. Menuline items canbecut, copied andpasted from anymenuto anotherforeasy editing. Keypads

can also be programmed and edited remotely via modem.

Three LEDs (red, green and yellow), located above the rocker keys, can be individually instructed (from the Event Manager schedule) to

turn on, turn off, blink fast or blink slow based on any condition(s).

The LCD-96M has a built-in high-contrast green backlight that can be programmed to stay on continuously or turn on with any key press

thentimeoutafteraspecifieddelaytime. ThebacklightandmenuselectionscanalsobeaccessedviatheEventManagerscheduletoallow

dynamic interaction with other system functions.

Upto16LCD-96MKeypadscanbeconnectedina"daisy-chain"toStargate'sRS485portusingtwotwistedpairsofcatagory-5cable(one

pair for communication and the other for 12vdc power) or homerun (star wired) to an optional RS-485 hub. Up to 4 LCD-96M Keypads

can be powered by Stargate's on-board 12vdc power supply. Five or more keypads require an external 12vdc power supply.

The LCD-96M faceplate measures 4"W x 4 3/4"H and snaps into an included wall-mount enclosure (3 3/8"W x 4"H x 2"D) for easy

installation.

Dual-Position

Rocker Buttons

LED Indicators

Vent

Menu Lines

LCD Menu Screen Stores 96 User-Defined Menus & Sub-Menus

Programmable from Event Manager software

Supports Text & Graphics (.bmp)

8 Dual Position Rocker Keys

Independent Left/Right Programming

3 Programmable LEDs (On/Off/Blink)

Continuous or Timed Backlight

VoiceMail Menu

Caller ID Name & Number Log

Thermostat Menu With 16 Zone Access

Reliable RS-485 Communication

Simple 4-Wire Connection

Low Current Draw (100ma @ 12vdc)

Colors: White, Black, Custom

LCD MULTI-MENU KEYPAD

LCD-96M

3 3/8"

Hole Cut Out

Template

RS-485 Connector

POT1

Screen

Contrast

Adjust

Lock Wings

(open)

INSTALLING THE LCD-96M

1) Choose a convenient location to install the LCD-96M Keypad. For best visability, install the keypad at eye level.

2) Using the Hole Cut-Out Template on the previous page, put a small pencil mark on the wall in the four corners of the cut-out.

3) Draw lines to connect the four pencil marks.

4) Check that the horizontal lines are level prior to cutting out the hole.

5) Carefully cut out the 3 3/8" x 4" hole with a dry wall utility knife.

6) Slide the Catagory-5 cable through the access hole in the back of the enclosure.

7) Insert the enclosure into the wall with the lock wings closed flush against the top and bottom of the enclosure (figure 1).

Be sure the side marked "THIS SIDE UP" on the back of enclosure lip is facing up and the lock wings are back far enough behind

the enclosure lip to accommodate the thickness of the wall (figure 2).

8) Once inserted, lock the enclosure in place by tightening the two lock wing screws.

9) Terminate the four wires of the Catagory-5 cable onto the screw terminal connector (figure 3) and plug into back of keypad.

10) Place the top of the keypad over the top lip of the enclosure then carefully snap the bottom in place (figure 4).

Catagory-5

cable

Lock Wings

(closed) “THIS SIDE UP”

Lock Wing

Screws

Figure

1Figure

2Screw

Terminal

Connector

Figure

Screw Terminal Connector

+12vdc

GND

B+

A-

Orange

White-Orange

Blue

White-Blue

Green

White-Green

Brown

White-Brown

CATAGORY-5CABLE

Not Used

Figure

}

Keypad #1 Keypad #2 Keypad #3 Keypad #4

Keypad #8Keypad #7Keypad #6Keypad #5

RS-485 HUB #1

RS-485 HUB #2

Keypad #16Keypad #15Keypad #14Keypad #13

Keypad #9 Keypad #10 Keypad #11 Keypad #12

To RS-485 HUB #3

Catagory-5

Cable

+12v

GND

B+

A-

STARGATE

RS-485 Connector

CONNECTION USING RS-485 HUB AND HOME-RUN (STAR) WIRING

An optional RS-485 Hub can be used to allow home-run (star format) wiring of keypads to Stargate. The RS-485 Hub can accom-

modate up to 8 RS-485 devices (keypads, thermostats, etc.). Additional hubs can be connected to accommodate up to 32 devices.

NOTE: Each hub requires an external 12vdc @ 1A power supply. DO NOT power a hub from Stargate's 12v power

source. When connecting two or more hubs, the RS-485 inputs and ground connection of each hub should be connected in a "daisy-

chain" configuration (see diagram). Catagory-5 twisted-pair cable is recommended for all RS-485 connections. Total cable length

should not exceed 4,000 feet.

B+

A-

+12vdc

Ground

12vdc

@1A

Power

Supply

12vdc

@1A

Power

Supply

B+

A-

+12vdc

Ground

CONNECTION USING DAISY-CHAIN (LOOP) WIRING

Up to 16 LCD-96M Keypads can be connected in a "daisy-chain" to Stargate's RS485 port using two twisted pairs of catagory-5 cable (one pair

for communication and the other for 12vdc power). Up to 4 LCD-96M Keypads can be powered by Stargate's on-board 12vdc power supply.

Total cable length should not exceed 4,000 feet.

+12vdc

Ground

B+

A-

STARGATE

RS-485

TERMINALS

Keypad #1 Keypad #2 Keypad #3 Keypad #4 Keypad #5

12VDC

POWER

SUPPLY

+12v

Ground

Catagory 5 Twisted Pair Cable (max length 4,000 ft.)

+12vdc

Ground

B+

A-

12VDC

POWER

SUPPLY

+12v

Ground

Whenconnecting anexternal12vdc power source atthekeypad location,adda 100-ohm, 1watt resistorinseries withtheground wire feeding the

keypads.

When connecting 5 or more LCD-96M keypads, an external 12vdc power source is required. Allow 100mA for each LCD-96M. If the external

12vdc power source is located near Stargate, connect the NEGATIVE (Ground) wire of the power supply to the GROUND terminal of Stargate's

RS-485 connector.

+12vdc

Ground

B+

A-

STARGATE

RS-485

TERMINALS

Keypad #1 Keypad #2 Keypad #3 Keypad #4

Catagory 5 Twisted Pair Cable (max length 4,000 ft.)

100-OHM

1 WATT

RESISTOR

Catagory 5 Twisted Pair Cable (max length 4,000 ft.)

SETUP

1) Connect 12vdc power and RS-485 network pair (B+, A-) to the keypad(s).

(NOTE: Some Stargate RS-485 connectors are labeled "TRB" instead of B+ and "TRA" instead of A-)

If an external 12vdc power supply is used, you MUST connect the ground (negative) of the power supply to the ground (-) terminal

of Stargate. The 3 LEDs will blink for several seconds as Stargate establishes communication with the keypad.

2) After the LEDs stop blinking, press and hold the top button (either side) until the Setup menu screen appears (about 6 seconds).

NOTE: Setup can only be accessed from the Main Menu (Menu #1) top button.

3) If the screen appears blank or faint, using a small screwdriver, slowly turn the tiny screen contrast control ("POT1") near the

RS-485 connector on the back of the keypad (see page 4).

4) Set the keypad address to a number from 1 to 16 using the #2 button labeled "Addr". Press the right side of the button to

increment or the left side to decrement. NOTE: Each LCD-96M must be set to a different address number.

5) Set the default menu screen number (menu screen to go to after timeout) to a number from 1 to 96 using the #3 button labeled

"Default Scrn". For Main Menu set to 1.

6) Set the default menu screen timeout (seconds) using the #4 button labeled "Scrn Tout". Set to "00" to disable the timeout or a

number from 15 - 255 seconds. If a menu is selected from the keypad, it will revert back to the default menu after the menu screen

timeout. Menus selected from the schedule using "Goto Menu" will not timeout.

7) Set the display backlight timeout using the #5 button labeled "Bklt Tout". Set to "00" to keep backlight on continuously or a

number from 15 - 255 seconds to have it turn off after the selected number of seconds have elapsed since the last button press.

8) Set the Time Display Format (12 hour or 24 hour) using the #6 button labeled "TimeFrmt".

9) Select CallerID Auto Display on/off using the #7 button labeled "AutoCID".

When CallerID Auto Display is on, the menu screen automatically switches to the Caller ID display menu on incoming calls.

To function, your phone line must be equipped with Caller ID service and Caller ID must be enabled in the WinEVM Define -

Telephone field.

10) Press the bottom (#8) button to return to the Default (Main) Menu.

Press and hold the top button

to access the Setup menu.

Setup

Ver:1

Addr: 1

Default

Scrn 0

Scrn Tout:

00 sec

Bklt Tout:

00 sec

TimeFrmt

12 hour

AutoCID:

<< Main

Sets Keypad Address

Sets Default Menu

Sets Menu Screen Timeout

Sets Backlight Timeout

Sets Time Display Format

Return to Main Menu

Sets Auto Display Caller ID

PROGRAMMING AND OPERATION - Introduction

1) Open Event Manager for Windows (WinEVM).

2) Click DEFINE - LCD KEYPAD.

3) Select the LCD Keypad address you want to program then click DEFINE to open the LCD KEYPAD programming utility.

4) Click the SETUP KEYPAD button.

5) Enter a name and location for the keypad. Set or change the timeout parameters (if not already set at keypad). Click Apply then OK.

6)Clickthe "Select" button in the MENU SCREEN SELECT section to select the Menu number you want to program then type a name for

the menu (ie: "MAIN") in the "Name" box.

7) Click on an ACTION you want to assign to a keypad button, then drag the action onto the menu screen (to the left of the desired keypad

button). This will bring up an edit field for the type of action selected.

8) Complete the edit field then click OK to accept the action or CANCEL to escape.

NOTE: The left and right side of a keypad button can each be programmed to perform different actions.

Click the "RIGHT BUTTON SAME AS LEFT" box when you want both sides to perform the same action.

9) Repeat step 7 for each button in the menu you want to program.

10) Click DOWNLOAD MENU to load the LCD-96M with the new menu or select another Menu number to program and repeat steps 6

- 9.

11) To download all defined menus to the LCD-96M, click DOWNLOAD ALL. This may take a few minutes depending on the number

of menus and content (text/graphics) being downloaded. It is not necessary to DOWNLOAD ALL menus if each menu is downloaded

individually.

12) Click OK to exit.

Drag the action onto

the menu screen

10 CopyKeypad

Select

PROGRAMMING AND OPERATION - Introduction

BUTTON ACTIONS

There are three types of button actions that can be assigned, Custom, Navigation and Predefined Menu.

CUSTOM (Then Action, X-10 Two-Way)

Then Actions include X-10, IR, Relay, Macro, VoiceMail, Flag, Variable, HVAC, Audio Path, LCD Keypad and are treated the

same as Then Actions used in the schedule.

X-10 Two-Way action allows single button X-10 control of on, off, dim and bright functions with on/off status indication (inverted

background = on, normal = off).

NAVIGATION

Navigational functions include "do nothing", "go to menu"and "previous menu". These allow switching to specific menus or previ-

ous menu. "Do nothing" prevents the associated keypad button from performing any action but the menu line can still

display text or graphics.

PREDEFINED MENUS

PredefinedMenusaremenusscreenswithpre-definedfunctionandlayout. TheyincludeThermostat,VoiceMail,TimeLabel,Variable,

Caller ID, DigitPad and TelePad. Time Display is a single pre-defined Menu Line. The bottom button of the Thermostat, VoiceMail,

CallerID,DigitPadandTelePadmenusreturnstotheMainMenu(leftbutton)orPreviousMenu(rightbutton). Theseareidentifiedwith

the graphic for "Main" menu and for "Previous" menu.

SIZE

Selects the type size of the text on a menu line. 5 x 7 supports up to 10 characters. 6 x 8 supports up to 8 bold characters.

ALIGNMENT

Selects the vertical placement of the text on a menu line.

JUSTIFY

Selects the horizontal placement of the text on a menu line.

CUT, COPY, PASTE, DELETE, EDIT

Performs the corresponding function to the selected menu line.

COPY KEYPAD

Copies all menus from the selected keypad to another keypad.

DOWNLOAD SCREEN / DOWNLOAD ALL

Download Screen loads only the displayed menu into the LCD-96M keypad.

Download ALL loads all defined menus into the LCD-96M keypad.

CopyKeypad

10:19 PM

Select

Indice

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo