Jenlis Weed Razer Express Manuale utente
Item 580125
Product Manual
WeedRa er
xpress
Product Contents................ 2
Assembly Instructions . . . . . . . . . . .3-4
Operating Instructions ............ 4
Blade Sharpening Instructions ...... 5
Safety Instructions............... 6
Replacement Parts .............. 7
Product Warranty................ 8
Table of Contents:
www.weedrazers.com
Important Information:
2
Please read these instructions thoroughly before use. Failure to follow instructions
may result in equipment damage or failure, losses, injury or death.
WARNING:
To reduce the risk of injury:
•The WeedRazer is designed for cutting submerged, partially emergent,
or emergent aquatic vegetation from underwater. Any other use is strictly
prohibited. Before using the WeedRazer, please read this manual carefully to
understand the proper use of the unit.
•The WeedRazer blade(s) are razor sharp. The blade covers should be on while
assembling the tool and when tool is not in use. Failing to comply can result in
severe lacerations, dismemberment, and even death.
SAFETY FIRST:
Instructions containing a warning within this manual are marked with a symbol.
Keep out of reach of children.
Do not use with children in immediate area.
IMPORTANT: Jenlis, Inc®is not responsible for equipment damage or failure,
losses, injury or death resulting from failure to follow safety
precautions, misuse or abuse of equipment.
PRODUCT CONTENTS:
C
L
DGI
A
B
F
E
K
HJ
PART QTY
A Handle 1
B Angled Handle 1
C Blades 2
D Support Bracket 2
E Handle Connector 1
F Weed Deector 2
PART QTY
G Nylon Spacer 2
H 1.5" Bolt & T-Nut 1 ea.
I 1.5" Bolt, Nut, Washer 1 ea.
J 1.2" Bolt, Nut, Washer 5 ea.
K Rope 25' 1
L Blade Sharpener 1
www.weedrazers.com 3
Notes:
Assembly & Instructions
Tools Required:
• #3 Phillips Screwdriver • 7/16” Wrench
Step 1
Insert 4 of the 1.2” Bolts (J) into the four outermost
holes of one of the triangular Support Brackets (D)
making sure to slide the bolts through the domed
side, then place the bracket on a flat work surface
with the screw heads down. Place a Nylon Spacer
(G) on each of the bolts at the base of the triangular
bracket.
Step 2
Place each Blade (C) onto the Support Bracket (D)
so that each blade edge faces outward and the
holes seat over the two bolts at the narrow end
of the triangular bracket. Next, seat the second
triangular Support Bracket (D) over the assembly
with the domed side facing up and place a washer
and nut on each of the four bolts—be sure to
simply hand tighten at this time.
Step 3
Slide the blade covers back about 2” to make
room for the handle. Take the two halves of the
Weed Deflector (F) and snap together at the pins
molded into each piece. Slip the Weed Deflector
(F) onto the Angled Handle (B) at the end with
two holes making sure that the hole in the Weed
Deflector aligns with the second hole from the end,
then slide the Angle Handle (B) into the Support
Bracket (D) so that the holes align. At this time, the
blade covers can be slid back into place for safety
and will ride up over the Weed Deflector slightly.
www.weedrazers.com
4
Notes:
Assembly & Instructions (con’t)
Step 4
Next insert a 1.2” bolt (J) into the hole at the base
of the Support Bracket and a 1.5” bolt (I) through
the hole with the Weed Deflector (F), then secure
each with a washer and nut. Tip the assembly
upright and tighten all fasteners securely using a
Phillips screwdriver and 7/16” wrench.
Step 5
Handle Assembly—Press the spring-loaded
buttons on one end of the Handle Connector (E),
slide into the open end of the Handle (B) and turn
until the buttons snap into the holes in the handle.
Repeat this process for the second half of the
handle.
Step 1
Throw the Weed Razer out and over area to be
cleared. If you are on a dock, tie the rope to a post
so you don’t throw too far.
Step 2
Let the Weed Razer sink.
Step 3
Pull back in using short, hard, jerking motions.
Repeat as many times as needed to clear your
weeds.
Operating Instructions
www.weedrazers.com 5
Step 1
Always wear cut resistant gloves when handling
the Weed Razer.
Step 2
Stand the assembled Weed Razer up and grip
the handle in one hand, or rest the handle of the
Weed Razer against a wall or building.
Step 3
Kneel or sit in front of the Weed Razer in a stable
position (Figure 1). Do not sharpen while standing
or leaning over the cutting edge.
Step 4
Hold the sharpener with your thumb resting
on the flared ridge of the sharpener. Wear cut
resistant gloves to protect your hands if you slip
while sharpening.
Step 5
Run the sharpener down the cutting blade edge
in four to six strokes using less pressure as
the edge gets sharper. Press one edge of the
sharpener’s steel on the edge of the blade that
you want to sharpen, then switch to the other
side of the sharpener’s steel for the other side of
the blade.
Step 6
To sharpen the opposite side of the blade, either
switch hands or turn the Weed Razer around so
the opposite edge is in position for sharpening.
Notes:
Blade Sharpening Instructions
WARNING
Fig. 1
www.weedrazers.com
6
Notes:
Safety Instructions
1. Always wear cut resistant gloves when
handling the Weed Razer, especially during
and after removal of the blade covers.
2. The Weed Razer is to be operated by hand
only. Do not pull the Weed Razer behind a
boat or any other machine driven equipment.
Doing so will void the warranty and damage
your Weed Razer.
3. Do not use with children in immediate area.
4. Do not use the Weed Razer when humans
and/or animals are present within 100 feet
from the launch point.
5. Do not place or use near electrical wires or
cords.
6. Never touch the sharp edges of the blades
with bare hands at any time.
7. Leave blade covers on the cutting edges
when not in use.
8. Check all bolts, connections, and rope before
use.
9. Avoid areas with underwater structures.
10. When not in use, store in a safe location out
of the reach of children.
NOTE: Failing to comply can result in severe
lacerations, dismemberment, and even death.
Do not pull behind a boat
Do not pull behind a vehicle
or any mechanical device
WARNING
Do not use when humans or animals are within
100 feet from the launch point
www.weedrazers.com 7
Notes:
Replacement Parts
Replacement parts can be found online at www.weedrazers.com
V1
8View other great products on-line at www.weedrazers.com
ONE YEAR MANUFACTURER’S WARRANTY:
1-Year Manufacturer’s Warranty – Jenlis, Inc. warrants this product to be free from
defects in workmanship and materials, under normal, non-commercial use and conditions,
for a period of (1) one year from the original invoice date. Warranty Limitations – Damage
resulting from use in commercial environment, misuse, abuse, negligence, and/or accidents.
The manufacturer agrees, at its option during the warranty period, to repair any defect in
material or workmanship, or to furnish a repaired or refurbished product without charge. All
warranty claims must be sent to Jenlis, at the customer’s expense. Return shipping will be
pre-paid. All returns must be pre-approved. Please visit www.weedrazer.com/warranty for
an RMA number prior to returning product. Returns without RMA’s will be refused.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Jenlis Taglierina
