Jetboil FLASH Manuale utente

Cooking System

Instructions

FLASH

Important: Read these warnings and instructions carefully

prior to assembling or using this product. Fully familiarize

yourself with this product before connecting it to a fuel

canister. Keep these instructions for future reference.

WARNING

FIRE OR EXPLOSION HAZARD

If you smell gas:

1. Do not attempt to light appliance

2. Make sure appliance is in the oﬀ position.

3. Extinguish any nearby ﬂame(s).

4. Shut oﬀ cylinder fuel supply valve if so

equipped, or if equipped with a disposable fuel

cylinder, disconnect cylinder

5. Leave the area immediately.

6. Allow gas to dissipate 5 minutes.

7. If gas smell has dissipated from the area,

of the appliance, and fuel supply, follow gas

connection procedures.

8. If you smell gas again, follow steps 1-6 and

have appliance serviced.

Failure to follow these instructions could result

in ﬁre or explosion, which could cause property

damage, personal injury, or death.

ONLY USE OUTDOORS IN A WELL-VENTILATED AREA IN

ORDER TO AVOID ENDANGERING YOUR LIFE

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide

which is poisonous and has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space

such as a camper, caravan, tent, car, mobile

home, marine craft, or home.

FOR YOUR SAFETY

Donot store or use gasoline or other flammable vapors

andliquidsinthevicinityofthis or anyother appliance.

•Donotmodify this appliance.This may be hazardous and will void the warranty.

• Burn Hazard - Accessible parts may become very hot.

• Do not leave this appliance unattended while the appliance is in operation;

keep children and pets away from the appliance at all times

• Improper installation, use, adjustment, alteration, service, or maintenance

can cause injury or property damage. Refer to this manual. For assistance

or additional information consult a qualiﬁed installer, service agency or

gas supplier.

DANGER

WARNING

TABLE

OF CONTENTS

GENERAL WARNINGS .................1-2

SPECIFICATION ..............................4

LEAK CHECK PROCEDURE .............4

FIGURES .........................................5

ASSEMBLY ......................................6

OPERATING INSTRUCTIONS ......7-8

STORAGE AFTER USE .....................8

MAINTENANCE ..............................8

TROUBLESHOOTING ......................8

FRENCH TRANSLATION ...............10

INTERNATIONAL TRANSLATIONS...19

SPECIFICATIONS

LEAK CHECK

PROCEDURE

Gas category: Direct Pressure – Butane-Propane mixture. Canister

must conform to the EN417 or AS2278 standard. This appliance is only

intended for use with 100g/230g/450g Jetboil Jetpower Isobutane/

Propane Fuel Canisters (sold separately). It may be hazardous to

attempt to ﬁt other types of gas containers.

Jet Size: 0.27mm Gas Consumption: 7 MJ/hr (AU) || 139 g/hr [2 kW]

(EU) || 9,000 BTU/hr (CA)

Minimum Storage Temperature: -40°F / -40°C

Minimum Use temperature: 0°F / -20°C

1. Perform leak checks outside, in a well-ventilated area.

2. Connect fuel canister (3.1) to valve (3.2) by threading in the

orientation shown in Fig 4.

3. Put soapy water on the gas connection between fuel canister and

the valve. Formation of bubbles indicate a gas leakage.

Do not check for leaks using a ﬂame.

If a leak is detected, do not attempt ignition. Remove fuel

canister immediately and contact Customer Service.

4. If no leak is found, detach fuel canister. Leak check is complete. 4

FIGURES

Fig. 11

Fig. 12

Fi Fig. 9

Fig. 10

Fig. 7

Fig. 4

Fig. 3

Fig. 1

Fig. 6

Fig. 8

Fig. 2

Fig. 5

1.1

5.1

8.2

8.1

11.1

1.31.3

2.2

2.1

2.3

12.2

12.1

1.2

3.2

10.1

10.2

7.2

7.1

3.1

DO NOT

HEAT EMPTY

LIGHT BEFORE

ATTACHING

POT

1. Remove packed contents from pot (Fig 1).

2. Perform LEAK CHECK PROCEDURE (See Page 4).

3. Unfold the bail (2.1) from the valve body (2.2).

4. Close the control valve (8.1) (turn clockwise).

5. Check for debris in the valve connection (1.1), and that the O-Ring is in place

and in good condition before connecting to the stove.

Donotusetheapplianceifithasdamagedorwornseals,thismayresultingasleakage.

Intemperatures belowfreezing,O-Ringsmay notsealfully,resultinginafuelleak.

6. To check that the gas canister is not empty, liquid fuel may be heard and/or felt

inside when the canister is shaken.

7. Connect fuel canister (3.1) to valve (3.2) by threading in the orientation shown in Fig

4. Hand tighten only, do not over-tighten or cross-thread. May damage

seals resulting in fuel leak.

8. Unfold stabilizer legs (2.3) and securely attach stabilizer to fuel canister (Fig 5).

9. Place assembled stove on a ﬂat, level surface, at least 1m/3.3ft away from any

combustible materials or ignition sources.

10. If using Pot Support (sold separately): Unfold pot support legs (12.1), place it on top

ofburner baseandrotatetolock(12.2).Confirm thatsupportisfullyattached, seatedandstable.

Never use alternate cookware without the Jetboil Pot Support. Failure to

use the Pot Support will result in a ﬁre that may cause death or serious injury.

Never use cookware larger than 2L capacity or 9in. [23cm]

diameter when using a Pot Support.

ASSEMBLY

• Perform Leak Checks outside, in a well-ventilated area.

• Operate at least 1m/3.3ft away from combustible materials and ignition sources.

• Before each use: Keep stove area clear and free from combustible

materials, gasoline, and other ﬂammable vapors and liquids.

• Do not obstruct the ﬂow of combustion and ventilation air to the stove.

• Do not use windscreen or outback oven; this can overheat the fuel canister,

resulting in explosion.

•Do not use anappliance which isleaking,damaged or which does notoperateproperly.

• Always change gas canisters in a well ventilated location away from any

sources of ignition, such as naked ﬂames, pilot, electric heaters/equipment

and away from other people.

WARNING

Preparation:

1. Remove bottom cover (7.1) from bottom of the Jetboil pot (7.2). 2. Remove Pot

Support Warning Tag and Pack Bag (if included). 3. Add contents to the pot, cover

with lid, but do not put the pot on the stove yet. Now you are ready to light the burner.

4. Test igniter by depressing igniter button (8.2) until click is heard. If it does not

spark, refer to Maintenance and Troubleshooting sections.

Performance may be suboptimal if used in extreme conditions

(cold, hot, wind, altitude).

Do not use stove to warm fuel canister. Can result in explosion.

Lighting the Burner:

Ensure burner base is free of any pot prior to lighting. Gas build-up can

occur, resulting in increased ﬂame eruption.

1. Open control valve (8.1) counterclockwise until fully opened and gas ﬂow can be heard.

2. To light, depress Igniter Button (8.2) until click is heard. Repeat as necessary

until ignition (Fig 9). 3. If ignition does not occur within 5 seconds, close control

valves and wait 5 minutes before repeating the procedure.

• Keep burner at arm’s length, away from face, during ignition. Flame can

ﬂare during ignition.

• Do not attempt to light with included pot or any other cookware on the

burner. Gas build-up can occur, resulting in increased ﬂame eruption.

• Never expose stove to ﬂammable vapors or liquids while lighting the burner.

It can cause an explosion or ﬁre.

• Do not heat empty pot. Product will melt and potentially catch ﬁre.

• Do not move, lift, or tilt stove with lit burner. Product damage or injury can

occur due to ﬂaring.

• Do not ﬁll above maximum ﬁll line. This may cause boil-over, resulting in injury.

• If attempting to heat anything other than water, use care and stir frequently

to avoid boil over or scorching, which may result in product damage or injury.

• Always check that the burner is extinguished before disconnecting the fuel canister.

• Do not use for boiling oil or deep frying. Product damage or injury can occur

due to overheating.

OPERATING INSTRUCTIONS

WARNING

Usage:

1. If necessary, rotate control valve (8.1) clockwise to decrease ﬂame setting.

2. Once the burner is lit, carefully place the pot with its contents on the burner

base (Fig 10); turn as shown in Fig 11 to lock into place. 3. Heat indicator: As

the pot heats, the heat indicator (11.1) will turn from Black to Orange. If

the heat indicator is Orange, the pot and its contents are above 149°F (65°C).

Use care when removing lid. Steam and/or

contents may be hot and can cause injury.

TRUCTIONS After Use:

1. Turn oﬀ control valve (8.1) (tighten clockwise) to

extinguish ﬂame. 2. Remove pot from burner base – hold pot by cozy (10.1), and

base by shroud (10.2).

Exposed metal parts will be hot and may cause injury if touched.

3. Always disconnect fuel canister after use. Unscrew fuel canister from burner

base (Fig 4), and replace plastic fuel cap.

Always check that the burner is extinguished before disconnecting the

fuel canister. Vapors can ignite and cause serious injury.

Packing:

1. Allow stove to fully cool before packing. 2. Place bottom cover (7.1) on pot (7.2).

3. Remove stabilizer from canister and fold for storage (1.2). 4. Fold Valve bail

under valve body (1.3). 5. Ifusing the potsupport: Remove pot support fromburnerbase

(Fig 12), and foldlegs (1.4). 6. Refer to Fig 1 for packing contents into pot.

STORAGE AFTER USE

1. Always disconnect fuel canister before storing the stove. 2. Ensure stove and

pot are clean and dry before storing. 3. Store the stove in a cool, dry location,

indoors.

MAINTENANCE 1. Flame Check (Every use): The height of the ﬂame should

increase from low to high with counter-clockwise rotation of the control valve.

Flame should be blue with no yellow tipping at full output. Flame should not ﬂash

back into burner or lift oﬀ of burner top. If ﬂame abnormalities are found, see

your dealer or contact Jetboil for service. 2. Cleaning Pot (before storage, or as

needed): Allow pot to cool before cleaning. Do not use a dishwasher or abrasive

compounds (sand, salt, etc.) to clean. Only wash by hand with soapy water.

TROUBLESHOOTING 1. Flame does not extinguish: Tighten valve as much as

possible, blow out ﬂame, and immediately detach fuel source. See your dealer or

contact Jetboil for service. 2. Igniter fails to spark: If igniter will not spark, check

positioning of electrode in relation to burner. Approximately 1/8” (3mm) length of

igniter wire should protrude from the igniter ceramic. Wire should point toward

center of burner with a 1/8” (3mm) gap between the end of the wire and the top

surface of the burner. If not positioned as described, re-position the electrode

accordingly. Bend wire towards center of burner head and position as described

above. If stove is wet, igniter may fail to spark. If igniter fails to spark, use matches

or a lighter, following instructions detailed in OPERATING INSTRUCTIONS –

Lighting the Burners. See your dealer or contact Jetboil for service if igniter fails

to spark for any other reason. 3. If an issue cannot be corrected using these

instructions, see Limited Warranty on back page.

Système de

cuisson

FLASH

Important: Lisez attentivement ces avertissements et

instructions avant d’assembler ou d’utiliser ce produit.

Familiarisez-vous avec ce produit avant de le connecter

à une cartouche de combustible. Conservez ces

instructions pour référence ultérieure.

Indice

Lingue:

Altri manuali Jetboil Attrezzatura da cucina

Jetboil

Jetboil STASH Manuale utente

Manuali Attrezzatura da cucina popolari di altre marche

Petromax

Petromax h-fs56 Manuale utente

Beech ovens

Beech ovens Exhaust Duct Design Manuale utente

AMC

AMC Navigenio Manuale utente

WOLL

WOLL PRESSURE PRO Manuale utente

Kool-It

Kool-It KCB-60-2 Istruzioni operative

Wolf Gourmet

Wolf Gourmet ICBWGCU100S Manuale utente

TIGMON

TIGMON Lauben SV01 Manuale utente

Firex

Firex BETTERPAN Manuale utente

bora

bora Classic 2.0 CKA2 Manuale utente

Royal

Royal Dirt Devil Hotpot Manuale utente

Rational

Rational SelfCooking Center SCC Guida all'installazione

Stalgast

Stalgast 745104 Manuale utente

Breville

Breville VST071X Manuale utente

Bake Max

Bake Max America BAFA Series Manuale utente

Russell Hobbs

Russell Hobbs 25490-56 Manuale utente

Salvis

Salvis AKC1 Manuale utente

edenox

edenox DBM-211-M-W Manuale semplice

Orbegozo

Orbegozo BT 2700 Manuale utente