JETI model JETIBOX profi Manuale utente
1
Index
JETI BOX PROFI
Introduction ..................................................................................... 2
1. Description of equipment ........................................................... 3
2. First Time Switch-On ................................................................... 3
3. Charging the Battery .................................................................. 4
4. Switch-On, Switch-Off ................................................................ 4
5. Long Term Switch-Off .................................................................. 4
6. Menu Navigation ........................................................................ 4
6.2 Language switching ............................................................. 5
7. Wireles Modes .............................................................................. 6
7.1 Monitor .................................................................................. 6
7.2 Tx MODULE mode ................................................................... 8
7.3 Telemetry Reception ............................................................. 9
8. Desktop ........................................................................................ 9
9. PPM monitor .............................................................................. 10
10. Telemetry with the EX System ................................................... 10
10.1 Display ............................................................................... 10
10.2 Storing of Data .................................................................. 12
10.3 On-line Telemetry on a PC ................................................. 13
11. 1st Generation Telemetry ......................................................... 14
11.1 Displaying ......................................................................... 14
11.2 Storing Data ..................................................................... 14
12. 1st Generation System and System EX ..................................... 15
13. MAIN MENU - ALARMS ............................................................... 17
13.1 JETIBOX PROFI Alarms ..................................................... 17
13.2 Alarms - Sensors ................................................................ 17
14. MAIN MENU - Memory ............................................................... 19
The JETIBOX profi is a mobile wireless device, offering maximum comfort to the user when
viewing, processing and storing telemetric data. An integral part of the JETIBOX profi is the
system JETI DUPLEX 2.4GHz, which can be alternatively operated in one of the two offered
wireless modes.
EN
JETI BOX PROFI
Introduction
2
15. MAIN MENU - Set-up .................................................................. 19
15.1 Set-up - Duplex .................................................................. 19
15.2 Set-up - Sound .................................................................. 20
15.4 Set-up - Profile .................................................................. 21
15.5 Set-up - Display ................................................................ 22
15.6 Set-up - Time ..................................................................... 22
15.7 Set-up - Update .............................................................. 22
15.8 Set-up - Main .................................................................... 22
16. Connection of the JETIBOX PROFI to a PC ................................. 23
17. Technical data ........................................................................... 23
18. Ti connector wiring ............................................................... 24
19. Safety information .................................................................. 25
19.1 Battery replacement ........................................................ 25
19.2 Safety policy ...................................................................... 25
20. Warranty, Service and Technical Support ................................ 26
20.1 Warranty and Service ....................................................... 26
20.2 Technical Support ............................................................. 26
JETI BOX PROFI
12
34
5
678910
11
Before first time switch-on please shift the
switch slider to a position closer to the
tramsmitter connector. Thereafter press for an
extended time the button ESC and the JETIBOX
profi will switch-on.
1. - 4 Navigation Buttons
2. - Enter for confirmation
3. - ESC for leaving the menu
4. - Graphic display
5. - Stereo Jack 3,5mm for earphones connection
6. - Three pin connector (Ji) for JETIBOX compatible equipment connection
7. - USB connector for JETIBOX profi to PC connection
8. - Battery switch
9. - Connector for transmitter connection (Ti)
10. - Loudspeaker
11. - Integrated antenna *
1. Description of equipment
2. First Time Switch-On
on
off
* when handling the JETIBOX profi avoid complete screening off the antennas, otherways range/sensitivity
may deteriorate.
EN
JETI BOX PROFI
3
The JETIBOX profi contains an internal rechargeable Li Po type battery as well as the matching
charging circuitry. The JETIBOX profi can be charged from three different inputs:
USB
Three pin connector (Ji)
Transmitter connector (Ti)
Battery charging is indicated by consecutive filling up of the battery symbol in the lower right
corner of the display. After the symbol becomes completely filled up, the input will be shown
from which the battery gets charged (Ti —transmitter connecting input, USB, Ji —three pin
connector). Charging of the battery is completed when the battery symbol is filled up.
•
•
•
3. Charging the Battery
4. Switch-On, Switch-Off
The JETIBOX profi is switched-on by pressing and holding the button ESC down for a few
seconds, or by connecting a voltage to one of the inputs. If you intend to switch-off the JETIBOX
profi, push again the push button ESC for a slightly extended time and the JETIBOX will start its
switch-off procedure. Switch-off is indicated in the main menu by rolling the upper bar to the
right and after it will be rolled to the end of the right corner, the JETIBOX will be switched-off.
For a long term switch-off of the JETIBOX profi apply the switch, see paragraph 2 „First Time
Switching on”. The factory default switch position is battery-off. It is advisable to disconnect
the battery if a long term disconnection is planned (several weeks or months). During full
disconnection there is no actualisation of time and date provided, therefore it is always
necessary to set-up time and date after switching-on again. Always adhere to the correct
switch-off procedure. Switch-off the JETIBOX profi by using button ESC first and thereafter
switch-off the battery. Never try to disconnect the battery for long term
disconnection by means of the switch while the JETIBOX profi is running!
5. Long Term Switch-Off
In the upper menu bar you can see the menu
name. The presence of a shifting bar in the right
corner of the menu signifies that the menu
consists of multiple items. By pressing the
“up/down” button you may move vertically
through the menu items until the shifting bar
sign reaches its lowest screen edge. With the
push buttons “left/right” you may move
through the menu horizontally.
Some menus contain items which the user may
set-up himself. These items consist of a
description and a value. You may recognize an
adjustable value by an arrow symbol to the left
or right adjacent to the value, see picture. If the
value is accompanied by an arrow left, a value
change can be achieved by pushing the “left”
button. If there appear both arrows in the
menu, you may alter the values by pushing the
button “left” or “right”.
6. Menu Navigation, change language
EN
JETI BOX PROFI
MENU Name Menu Bar
Description
Value
4
If there is a right direction arrow placed on the
left side of a menu item, then this item may be
changed/activated by the push button ENTER.
Items which cannot be set up are either marked
by a simple arrow or by an icon.
On account of better orientation are some
menus on the desktop marked by special
navigation icons. The first icon in the upper
right corner shows the position of the edited
item. A further icon illustrates the choice of
further embedding.
EN
JETI BOX PROFI
6.2 Language switching
When leaving the production line the JB embodies its initial set-up comprising English as
initial language. If you want to switch to a different language you should proceed as follows:
1. Switch-On the JETI BOX PROFI.
(see. Chapter 4)
2. Push the ESC key. In the main menu select
item SETUP and confirm with
the ENTER key.
3. Select item MAIN and confirm with
the ENTER key.
4. Select item Language and carry out
the requested language change with the aid
of the left/right key.
5
The JETIBOX profi contains a built-in wireless data transfer system Duplex 2.4GHz. The JETIBOX
profi can be operated in two wireless communication modes – “Monitor” or “Tx module”.
Mode switching sequence:
7. Wireles Modes
1. Switch-On the JETIBOX profi
2. Push ESC: Main menu, select item SET-UP,
confirm by ENTER
3. Select item DUPLEX, confirm by ENTER
4. Select item „ JETIbox mode“ and carry
out changes by arrows left or right
5. Prompt confirmation of mode change.
Select YES, confirm by ENTER
At present you have carried out a mode change. Description of particular modes see below.
EN
JETI BOX PROFI
7.1 Monitor
When using this mode the JETIBOX profi can only receive data via the existing connection
between the transmitter and receiver (listen). The JETIBOX profi cannot communicate with the
receiver without a switched on transmitter. If you want to operate the JETIBOX profi in this
mode it is therefore mandatory to carry out the binding procedure between the JETIBOX profi
and the transmitter as shown below.
6
Binding
During the binding process the JETIBOX profi adds the transmitter identification number to its
directory of equipment, which it is able to communicate with. Binding must be carried out
only, if the transmitter and the JETIBOX profi have never been bound before. If the JETIBOX
profi and the transmitter have already been bound at any time before, after switching on they
will automatically start communication with each other. In case of this mode the JETIBOX
profi is bound with the transmitter.
The sequence is as follows :
4. Select item DUPLEX. Check, if the
„Monitor“ mode is set.
Push ENTER in item Binding.
5. The item „Start“ will change into „Running…“
6. Switch-on the transmitter and thereafter the receiver.
7. After binding the item „Running …“ will change into „Start“ again and herewith
the procedure will be finished.
1. Switch-on the JETIBOX profi
2. Push ESC: Main menu, select item SET-UP
confirm by ENTER
3. Select item DUPLEX, confirm by ENTER
EN
JETI BOX PROFI
8 channel receiver
Monitor Mode
7
7.2 Tx MODULE mode
In this mode the JETIBOX profi is communicating bidirectionally directly with the receiver. The
JETIBOX profi receives telemetric and service data from the receiver. Via the standard PPM
signal, which is generated by most transmitters, the JETIBOX profi can simultaneously send
stick and controller settings to the receiver. The JETIBOX profi can simply serve as a transmitter
module replacement. Thanks to the universal mounting set it is simply done by installation of
the JETIBOX profi on the transmitter and by connecting the PPM signal including supply to the
JETIBOXu profi.
E x t .
P P M
1
2
D
D
a
n
t
sat2
satellite RECEIVER
PPM
8 channel receiver
Binding
During the binding process the JETIBOX profi adds the transmitter identification number to its
directory of equipment, which it is able to communicate with. Binding must be carried out
only, if the transmitter and the JETIBOX profi have never been bound before. If the JETIBOX
profi and the transmitter have at any time been bound before, after switching on they will
automatically start communication with each other. In case of this mode the JETIBOX profi is
bound with the receiver. Binding can be accomplished in two ways.
Tx MODULE mode
Automatic Binding:
Activate Binding in the receiver: plug-in the “bind plug” into the receiver input marked EXT
and connect the receiver supply.
Switch-on the JETIBOX profi. JETIBOX profi establishes communication with the receiver.
If connection of the JETIBOX profi with the receiver fails, check whether the mode set-up of
wireless communication correctly stands on “Transmitter”, see chapter “Wireless Modes”, and
repeat the procedure.
1.
2.
Manual procedure:
1. Switch-on the JETIBOX profi
2. Push ESC: Main menu, select item SET-UP,
confirm by ENTER
EN
JETI BOX PROFI
8
4. Select item DUPLEX. Check, if the
„Txmodule“ mode is set.
5. Activate Binding in the receiver: plug-in the “bind plug” into the receiver input marked
EXT and connect the receiver supply.
6. Go to item Binding and select -> Start,
confirm by button ENTER.
After execution of this step connection between
the JETIBOX profi and receiver will be
accomplished.
3. Select item DUPLEX, confirm by ENTER
8. Desktop
After switch-on of the JETIBOX PROFI you will be situated in the telemetric menu on the
desktop working area. In the lower part a status line shows operation modes of the JETIBOX
profi. Above the status line there are items showing telemetric data. The JETIBOX profi offers
up to 5 different desktops with 4 items on each, which can be set by the user. With push-button
“left/right” you can browse through the desktops, their sequence is shown below left in the
status line.
1- Four positions of telemetric data as defined by the user
2- Desktop sequence
3- Storing indicator of telemetric data and PPM
4- Menu of the external input „Ji“
5- Menu of the wireless module
6- Indicator of the active loudspeaker/earphones
7- Indicator of battery status or charging status while charging
8- Signal strength of receiver antennas
2 3 4 5 6 7 81
7.3 Telemetry Reception
If you do not connect a PPM signal when using the transmitter mode, the JETIBOX profi will
receive telemetry from sensors only which are connected to the receiver. The JETIBOX profi
will not transmit stick and controller positions. Deactivate the PPM alarm if you are going to
exploit the JB in this mode.
EN
JETI BOX PROFI
9
9. PPM monitor
In the PPM Monitor menu there are graphically shown deflections of particular channels. You
simply enter the PPM Monitor from the desktop. If you are on desktop 1, just push the “left”
button. The PPM Monitor menu consists of 8 indicators which graphically represent the
particular channel deflections. In the status line you will find the number of detected
channels. By pushing the “left” button again, 8 PPM channels may be featured .
In the wireless mode “TX module” the PPM signal will be decoded at the input „Ti“ and will
depict the deflections of particular channels in the PPM Monitor. If the JETIBOX profi is
switched to the wireless mode “Monitor”, the PPM Monitor will depict channel deflections of
the transmitter, which is communicating with the JETIBOX profi.
10. Telemetry with the EX System
The EX System telemetry is offering a wide potential for processing, depicting and storing
telemetric data. In order to view telemetry it is necessary, that the JETIBOX profi has either
picked up communication, using one of the wireless modes (see chapter Wireless Modes), or
the equipment must be connected to the external input „Ji“.
1. Select one of the four desktop items and
confirm by button ENTER.
2. Select item „Equipment“ and confirm
by ENTER.
3. Select an arbitrary equipment from the
directory - if there is no equipment shown on
the display, check if there exists a connection
and whether the sensor EX is connected to the
system. When starting first time or when a new
sensor is connected up the display of the
equipment may take a certain time.
4. Select an arbitrary equipment parameter-
complete displaying all parameters may afford
a certain time. When starting first time or when
a new sensor is connected up, the complete
display of all parameters may afford a certain
time
10.1 Display - Method of displaying telemetric values by the JETIBOX profi:
EN
JETI BOX PROFI
10
Altri manuali per JETIBOX profi
1
Indice
