JMPosner Multi Waffle Manuale utente
Multi Wafe Maker
Instruction Manual
2
IMPORTANT SAFEGUARDS
When using your Wafe Maker, safety precautions should always be
followed including the following:
1. PLEASE READ ALL INSTRUCTIONS BEFORE USING YOUR WAFFLE
MAKER.
2. All of the items described must be carefully observed when
operating the machine or performing maintenance work.
3. Do not touch hot surfaces. Use handles or knobs.
4. To protect against electric shock, do not place cord, plugs, or
appliance in water or other liquid.
5. Close supervision is necessary when the Wafe Maker is used by or
near children.
6. Unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts, and before cleaning the
appliance.
7. Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner.
8. Do not use outdoors.
9. Do not let the power cord hang over the edge of the table or
counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner or in a heated
oven.
11. When nished making wafes remove the plug from the wall outlet.
12. Do not clean non stick coated wafe plates with steel wool pads, or
other abrasive material.
13. When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of re, electric shock, and/or
injury to persons.
14. It is recommended that you discard the rst wafe made on your
new Wafe Maker.
15. Where this appliance is to be positioned in close proximity to
a wall, partitions, kitchen furniture, decorative nishes, etc., it is
recommended that they be made of non combustible material;
if not, they shall be clad with a suitable non-combustible heat
insulating material, and that the closest attention be paid to re
prevention regulations
16. Observe Warning Signs
3
INTRODUCING YOUR WAFFLE MAKER
1. Multi waffle
2. Allan key
3. Power cable
• Model no:
• Height:
• Width:
• Depth
• Weight
• Opt. temp:
• Electrical V:
• Electrical W
MULTI WAFFLE
513 mm
278 mm
539 mm
13 kg
185 C
220/240 V
1400 W
SPECIFICATIONS IN THE BOX
WAFFLE MAKER UNIT
Your wafe maker will come fully built and ready to use, this quick guide
helps you understand your wafe maker and its components.
Handle
Interchangeable plate
Control panel
Interchangeable plate
Handle
4
CHANGING WAFFLE PLATES
Changing the waffle plates on your Multi Waffle Maker is a straight
forward operation. Ensure the wafe plates are cool and the Multi
Wafe is not connected to the power supply, use the Allan key
provided to unscrew the 4 screws on the top and 4 screws on the
bottom housing. Remove the old plates and replace with new plates,
tighten each screw evenly. Your Multi Wafe Makers new plates are
ready for use.
ADDITIONAL PLATES
We currently have a wide range of additional waffle plates such as the
bubble waffle, stuffed waffle and more. They are easily removable so
that you will be able to quickly change them on site to react to your
customers ever changing demands. All of the plates are supplied with
non stick Xylan coating, this offers perfect waffles without the need to
spray the plates with oil. The Multi Waffle is also designed with the future
in mind, it allows us the opportunity to add new waffle plates as times
and trends change and even allows for custom made plates.
If you are interested in looking at getting more plates for your waffle
maker or a personalised custom made one please contact us at
5
CONTROL PANEL
BEFORE USING FOR THE FIRST TIME
• Remove all packaging materials and wipe cooking plates with
a damp cloth. When your wafe maker is new you may notice a
slight smoking effect or odour. This is normal with any appliance that
heats up and will not reoccur. This does not affect the safety or your
appliance.
•It is recommended that you discard the rst wafe made on your
new Wafe Maker.
NOTE:
• This appliance is intended for indoor use only.
• CAUTION: To ensure continued protection against risk of electric
shock, connect to a properly grounded power supply only.
SHORT POWER SUPPLY CORD
A short power-supply cord is provided to reduce risks resulting from
becoming entangled in or tripping over a longer cord. Longer extension
cords are available and may be used if care is exercised in their use.
If a long extension cord is used, the marked electrical rating of the
extension cord should be at least as great as the electrical rating of the
appliance. The longer cord should be arranged so that it will not drape
over the counter top or tabletop where it can be pulled on by children
or tripped over accidentally. If the supply cord is damaged it must be
replaced by one supplied by JM Posner or an authorised agent.
6
USING YOUR WAFFLE MAKER
1. The temperature on the display is Celsius.
2. Close the wafe maker and plug into Mains wall outlet, turn the on/
off switch on the side of the wafe maker to the on position. After
pressing the ON/OFF switch on the Display Panel you will see the
display go on, indicating that the Wafe Maker has power and is
ready for preheating. The power will remain ON until you unplug the
unit or switch the ON/OFF button again.
3. Set the desired temperature for making your wafes by pressing
up or down on the temperature buttons. The temperature will be
displayed on the panel. When cooking wafes the temperature of
the plates must always be over 170 degrees.
4. Until your wafe maker reaches the set temperature the “warming”
light will be illuminated and once your wafe maker reaches the set
temperature the ready light will come on.
5. When the desired set temperature is reached the ready light will
go off and on periodically, this is normal and is the Wafe Maker
keeping to the desired temperature.
6. Pour in just enough wafe mix to ll the lower wafe plate so that
the peak areas of the plate are covered. If necessary, use a spatula
to spread the wafe mix into the corners of the moulds. DO NOT use
oil on the plates as this will create carbon which is hard to remove
from a non-stick surface. The Auto Start Wafe Maker is preset to 3
minutes and 30 seconds standard cooking time. If you would like to
adjust the cooking time press the up/down time adjust buttons.
(NOTE) At the end of the cooking cycle the timer will stay at the
adjusted time of the previous cycle.
7. Close your wafe Maker and immediately turn anti clockwise 180º,
this will automatically start the timer. Once ready turn in a clockwise
direction 180º so that you can re-open your wafe maker and reset
the timer automatically.
CAUTION: If your wafe maker is opened without re turning 180º the
timer will not reset.
CAUTION: Opening too soon will cause unbaked wafes to split,
and make them difcult to remove.
8. If you want darker wafes, close the lid and continue cooking,
checking every 30 seconds.
9. Remove wafes from the plate with a non-metallic utensil.
10. For best results on your next wafe, wait until the ready light switches
off before pouring in new wafe mix.
11. When not using your wafe maker ,but leaving it heated on standby
the lid must be kept open to avoid damaging the non stick surface.
7
12. When you are nished baking, press the ON/OFF switch to turn off
your wafe maker, turn the switch on the side of the wafe maker
to off and unplug the unit from the wall outlet. Leave your wafe
maker open to allow to cool. After cooling, the plates may be
wiped clean with a damp cloth.
MAINTENANCE & CLEANING
• CAUTION: Be sure to unplug this appliance before cleaning. To
protect against electrical shock, do not immerse cord, plug or unit
in water or other liquids. After each use, always make sure the plug
is removed from wall outlet.
• After cooling any excess crumbs or oils can be wiped away with a
paper towel.
• Below the cooking plates there is a removable drip tray for ease of
cleaning.
•Wipe your wafe maker housings with a soft cloth. A little metal
polish suitable for stainless steel may be occasionally used on the
top housing. Do not use any abrasive scouring pads or steel wool,
as this will damage the housing nishing.
8
For more products please visit our website:
www.jmposner.com
JM Posner is a small team of experts dedicated
to bringing caterers and other professional’s
quality equipment and supplies at a fair price.
We believe our customers should have the
highest quality products which will leave their
own customers happy and coming back for
more.
Over the years, we have listened to our customers
and consequently improved our products in
order to match their needs in everyday working
life. We specialise in Chocolate Fountains,
Popcorn makers, Belgian Chocolate, Wafe
Makers and many more products.
Our aims are simple, be fair and be honest. This
is in terms of pricing, quality and the service we
offer, as we have all been customers of similar
products. Not only do we love what we do,
we’re also keen advocates of the products
we sell, this is simply by us tasting and trying the
products too. But most importantly to us, we
want you to enjoy the products as much as we
do. If our customers ever have a problem with a
product, we try to help through repairing them
or by offering after sales care by telephone or
email, we are always happy to hear from you.
We started when owner Justin rented chocolate
fountains to businesses and quickly discovered
they would prefer to have their own to use
on a daily basis. He soon found himself selling
chocolate fountains to businesses, but then
discovered they also wanted other products
such as popcorn machines and wafe makers,
this lead to JM Posner LTD being created and
we haven’t looked back.
Indice
Altri manuali JMPosner Macchina per waffle
