Johnson Controls S300 Series Manuale

24-10239-596 Revision D

December 2017

S300

Series

S300-DIN-RDR2SA

and S300-DIN-I8O4

hardware

installation

Johnson Controls

No part of this document may be reproduced without the prior permission of Johnson Controls.

If this document is translated from the original English version by Johnson Controls, all reasonable

endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable

for any translation errors contained herein or for incidental or consequential damages in connection

with the furnishing or use of this translated material.

Due to continuous development of our products, the information in this document is subject to

change without notice. Johnson Controls shall not be liable for errors contained herein or for

incidental or consequential damages in connection with furnishing or use of this material. Contents

of this publication may be preliminary and/or may be changed at any time without any obligation to

notify anyone of such revision or change, and shall not be regarded as a warranty.

Other Manufacturers’ Documentation

Johnson Controls does not duplicate documentation of other equipment manufacturers. When

necessary, Johnson Controls provides documentation that supplements that of other manufacturers.

When unpacking equipment, keep all original manufacturer documentation for future reference.

Technical Support

For factory technical support, Johnson Controls authorized field technicians or authorized dealer

representatives can contact Global Security Solutions Technical Support by phone at

(866) 893-0423 or (414) 524-1214, or by email at [email protected]. They

can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.

End users and customers should contact their local Johnson Controls branch or authorized dealer

for any of their support needs (technical support, maintenance contracts, on-site field support,

P2000 Software Service Agreements, Service Partnerships, and so on). Visit

http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.

For material returns contact the branch if the material was purchased through a Johnson Controls

branch or through the Product Sales Operations Team, if ordered through the Advanced Order

Management System (AOMS) and follow the RMA process; or contact the authorized dealer

representative where the material was purchased directly.

Acknowledgments

Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and

product names are trademarks or registered trademarks of their respective owners.

Declaration of Conformity

United States: This equipment, S300-DIN-RDR2SA and S300-DIN-I8O4, has been tested and

found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

The user is cautioned that changes and modifications made to the equipment without approval of

the manufacturer could void the user's authority to operate this equipment.

Canada: CAN ICES-3 (B)/NMB-3(B)

European Union: This product complies with the requirements of the EMC Directive.

This equipment must not be modified for any reason and it must be installed as stated in the

Manufacturer’s instructions. If this shipment (or any part thereof) is supplied as second-hand

equipment, equipment for sale outside the European Economic Area or as spare parts for either a

single unit or system, it is not covered by the Directives.

UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET

The following model numbers are listed under Underwriters Laboratories Inc. ® (UL) 1076 for Proprietary

Burglar Alarm Units and Systems, UL 294 for Access Control Systems Units and Underwriters Laboratories of

Canada ULC/ORD-C1076-86.

S300-DIN-RDR2SA

S300-DIN-I8O4

When installed at the site the following requirements must be met to comply with these standards.

1. The S300-DIN-RDR2SA and/or S300-DIN-I8O4 shall be mounted in subassembly S300-DIN-L or

S300-DIN-S.

2. The S300-DIN-RDR2SA and/or S300-DIN-I8O4 in combination with the S300-DIN-L or S300-DIN-S must

be connected to a UL Listed Uninterruptible Power Supply that provides a minimum of 24 hours of AC

emergency power.

3. The tamper switch must be enabled at all times.

4. Transient protection devices that are installed must not be removed or defeated.

5. Do not connect equipment to an AC power source that is controlled by a switch.

6. Model S300-DIN-RDR2SA or S300-DIN-I8O4 must use a Class 2 direct plug-in transformer rated 120 VAC

input and 24 VAC, 50 VA output from one of the following manufacturers:

Basler, part number BE116450CAA or BE116450AAA

Potter Electric Signal Co. (Amseco), model XR-2450LED

Revere Industries, model RT-2450SL/M

7. The sole use of a class 2 transformer to power the S300-DIN-RDR2SA or S300-DIN-I8O4 is only

acceptable for a UL 294 Listed system.

8. The sole use of a class 2 transformer to power the S300-DIN-RDR2SA or S300-DIN-I8O4 would not

provide battery standby power.

9. For a UL 294 Listed system the following Listed readers may be used.

10. UL 294 Performance Levels

Destructive Attack Level I

Endurance Level IV

Line Security Level I

Standby Power Level I

Manufacturer Model

HID Corp. 30387, 31503, 31815, 31880, 32005, 32788, 32985, 5355, 5365, 5395, 5405, 5455,

6005. All models may be followed by additional suffixes.

13.56 MHZ Models - iCLASS Models R10, R15, R40, RP10, RP15, RP40, RK40,

RPK40. All models may be followed by additional suffixes.

OSDP Models - iCLASS SE Models R10E, R15E, R30E, R40E, RP10E, RP15E,

RP30E, RP40E, RK40E, RPK40E. May be followed by “XXX”, may be further

followed by “NN”. Suffix explanation X1=Reader Colors: K = Black, G = Gray,

X2= Wiring, N = Pigtail, T =Terminal, X3 = “R” or “N”. The suffix “R” = Reader

Employed with RS485 Module, “N” = No RS485 Module present.

pivCLASS Models – pivCLASS reader models R10E, R15E, R30E, R40E, RP10E,

RP15E, RP30E, RP40E, RPK40E and RK40E, RPKCL40E, RKCL40E may be

followed by “XXX”. Suffix explanation X1 = Reader Colors: K = Black, G = Gray,

X2 = Wiring, N = Pigtail, T = Terminal, X3 = “R” or “N”. For use with the model

pivCLASS authentication module (PAM) M2000. May be connected directly to

S300-DIN-RDR2SA Data 0/Data1 Wiegand interface.

Mercury

Security Corp.

MR-5

Veridt, Inc. 900W2030, 900W2036, 900W2037

RDR2S-A and I8O4 Hardware Installation Introduction

24-10239-596 Rev. D

HARDWARE INSTALLATION

This document provides hardware installation instructions for the

S300-DIN-RDR2SA and the S300-DIN-I8O4.

INTRODUCTION

The S300-DIN-RDR2SA and S300-DIN-I8O4 modules provide interface

control for access and security devices associated with up to two doors.

NOTE: Throughout this manual the S300-DIN-RDR2SA module is also referred

to as the RDR2S-A, while the S300-DIN-I8O4 module is referred to as the I8O4.

S300-DIN-RDR2SA Module

Figure 1: S300-DIN-RDR2SA

RDR2S-A and I8O4 Hardware Installation Introduction

24-10239-596 Rev. D

The key features of the RDR2S-A include:

• Wide range nominal voltage for power source (+12 to 24VDC, 16 to

24VAC)

• Support for S300 RS-485 bus communications at 9600 or 19200 baud

(Automatic baud rate detection)

• Two-door access control input/output interface, each door’s interface

consisting of:

– Supervised door monitor switch input, normally open or normally

closed, based on wired configuration

– Supervised auxiliary access or exit request switch input, normally

open

– Supervised tamper and spare inputs

– Reader interface (Wiegand Data0 and Data1 interface or RS-485)

– Door strike relay, SPDT (Single Pole Double Throw)

– Alarm shunt relay, SPDT

– Red lamp driver and green lamp driver (open collectors)

– +12VDC 250mA reader power supply

• Calibration resistor input

• Supervised tamper and power fail inputs

• Support for Single Wire FICAM solution (requires physical address mode,

therefore, all other devices on that bus must also use physical address

mode)

NOTE: The FICAM solution requires Veridt readers connected to RDR2S-A

modules Version PS-217G and later. Do not power the Veridt readers from the

RDR2S-A module 12VDC output, you must use a separate 12VDC power

source to power the Veridt readers.

• OSDP reader support (implementation version 1) which supports

unencrypted communications between the RDR2S-A and the following

OSDP devices:

– HID OSDP keypad readers

– HID OSDP readers (no keypad)

In order to support OSDP readers, you must set the RDR2S-A DIP switch

for RS485. Both readers connected to the RDR2S-A terminal must be of

the same type.

RDR2S-A and I8O4 Hardware Installation Introduction

24-10239-596 Rev. D

The OSDP reader support includes communicating reader status.

Figure 2: System Diagram for OSDP Implementation Version 1

RDR8S

(PS-218)

E F G H

A B C D

CK721-A Controller

A B

Wiegand

reader

OSDP V1

reader

RDR2S-A

(PS-217)

A B

OSDP V1

reader

OSDP V1

reader Wiegand

reader

Note: The RDR2S-A can support up to two

OSDP readers or two Wiegand readers.

You cannot mix the two types of reader.

RDR2S-A and I8O4 Hardware Installation Introduction

24-10239-596 Rev. D

S300-DIN-I804 Module

Figure 3: S300-DIN-I8O4

The key features of the I8O4 include:

• Wide range nominal voltage for power source (+12 to 24VDC, 16 to

24VAC)

• Support for S300/RS-485 bus communications at 9600 or 19200 baud

(Automatic baud rate detection)

• 2 input/output interfaces consisting of 2 terminals, each terminal including:

– 4 supervised inputs

– 2 relay outputs

– 2 open collector outputs (OUT1 and OUT2)

• Calibration resistor input

• Supervised tamper and power fail inputs

RDR2S-A and I8O4 Hardware Installation Application

24-10239-596 Rev. D

APPLICATION

The RDR2S-A module supports up to two doors per unit. The I8O4 module

supports 8 inputs, 4 relay outputs, and 4 open collector outputs per unit.

Both RDR2S-A and I8O4 use standard S300/RS-485 communications and can

interface with the following controllers:

•CK722

•CK721-A

NOTE: A firmware update to all RDR2S-A and I8O4 modules is recommended

but optional if no change to the terminal configuration takes place. After

upgrading to CK721-A V3.0 or later, a firmware update to all RDR2S-A and

I8O4 modules is required if changes to the terminal configuration take place.

The RDR2S-A provides the ability to configure supervised 4-state inputs and

unsupervised 2-state inputs. When in physical address mode and used with

CK722 or CK721-A version 3.0 or later, any points not used for the door can be

configured as general purpose input/output (I/O) points, possibly eliminating

the need to purchase additional I/O modules for certain installations.

The RDR2S-A provides power for the card reader hardware. It does not

provide power for door locking hardware.

INSTALLATION

Unpacking the Equipment

Carefully inspect the S300-DIN-RDR2SA or S300-DIN-I8O4 shipping

containers as soon as you receive them (with the delivery agent present).

Some shipping companies want to have an agent present when a damaged

container is opened.

If a container is damaged, open it immediately, inspect the contents, and

have the agent make note on the shipping document. Check the purchase

order against the packing slips to ensure the order is complete.

If the contents of a container are damaged in any way, notify the carrier

and your Johnson Controls representative immediately. Report any

discrepancies to your Johnson Controls representative. Save the packing

materials for possible return shipments.

RDR2S-A and I8O4 Hardware Installation Mounting

24-10239-596 Rev. D

Package Contents

Package contents are as follows:

• S300-DIN-RDR2SA or S300-DIN-I8O4 module

• Connectors set

•This manual

Tools Needed

Small, straight-blade screwdriver for securing wires in the terminal

blocks.

MOUNTING

The RDR2S-A or I8O4 module can be mounted on a flat surface, DIN rail, or

in a Johnson Controls’ approved enclosure (for example: S300-DIN).

For information on mounting the RDR2S-A or I8O4 module in an enclosure,

refer to the manual provided with the enclosure.

DIN Rail Mounting

To mount an RDR2S-A or I8O4 module on a DIN rail:

1. Fully extend the white clips located on the bottom of the module.

2. Hook the module on top of the rail.

3. Push in the clips.

To remove a module from the DIN rail:

1. Pull down the clips at the bottom of the module.

2. Pull the bottom of the module out and lift it up.

Altri manuali per S300 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Johnson Controls Hardware per computer

Johnson Controls

Johnson Controls Frick XL Manuale del proprietario

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente