Johnson Controls Metasys MS-FEU1610-0U Manuale utente

FEU16x0 Field Equipment Controller Installation Instructions

Applications

The FEU16x0 Controller is a member of the Metasys® system Field Equipment Controller (FEC) family. The

controller is designed exclusively for use in a Metasys Release 8.1 smoke control application that is UL 864 UUKL/

UUKLC 10th Edition Smoke Control Listed. For Metasys system smoke control applications, you must refer to the

Metasys® System UL 864 10th Edition UUKL/ORD-C100-13 UUKLC Smoke Control System (LIT-12012487) for

detailed requirements and procedures for installing, commissioning, and operating UL 864 UUKL/UUKLC Listed

Metasys system devices. For example, the MS-FEU1610-0U can only be used with the Firefighters Smoke Control

Station (FSCS) panel manufactured by Automation Displays, Inc. (ADI). The UL 864 UUKL/UUKLC listing for

Smoke Control Equipment is voided if (1) you do not use the required software tools at the required versions; or (2)

you do not meet the requirements or do not follow the procedures as documented in the Metasys® System UL 864

10th Edition UUKL/ORD-C100-13 UUKLC Smoke Control System Technical Bulletin (LIT-12012487).

North American Emissions Compliance

Canada

United States

Installation

Observe these guidelines when installing the FEU controller:

• Transport the controller in the original container to minimize vibration and shock damage to the controller.

• Verify that all parts shipped with the controller.

• Do not drop the controller or subject it to physical shock.

Parts Included

• one MS-FEU1610-0U Controller with removable Terminal Plugs

• one Installation Instructions sheet

Materials and Special Tools Needed

• three fasteners appropriate for the mounting surface (#8 screws or M4 screws)

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur

du Canada.

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when this equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference, in which case the user will be required to correct the interference at his/her

own expense.

FEU16x0 Field Equipment Controller

Installation Instructions

MS-FEU1610-0U Part No. 24-10143-535, Rev. B

Release 8.1

Issued March 2018

FEU16x0 Field Equipment Controller Installation Instructions

• one 15.2 cm (6 in.) or longer piece of DIN rail and appropriate hardware for mounting the DIN rail

• small straight blade screwdriver for securing communication wires in the terminal blocks

• one phone jack splitter (optional)

Figure 1: FEU16 Controller Physical Features and Wiring Terminals

StatusLEDs

DeviceAddress

DIPSwitchBlock

BusEnd-of-Line

rminationSwitch

BinaryOutputs

Typically24VACTriacoutputs

ConfigurableOutputs

VoltageAnalogOutput

BinaryOutput

canbedefinedas:

(0-10VDC)

(24VACTriac)

24VAC,Class2

SupplyPower

TerminalBlock

UniversalInputs

VoltageAnalogInput

CurrentAnalogInput

ResistiveAnalogInputs:

DryContactBinaryInput

canbedefinedas:

(0-10VDC)

(4-20mA)

0-2kohm

RTD:1kNickel,1kPlatinum,orA99BSI

NTC:10kTypeLor2.225kType2

BinaryInputs

DryContactMaintained

PulseCounterMode

canbedefinedas:

(100Hzhigh-speed)

CoverScrew

SensorPort

(RJ-126-PinModularJack)

FIG:FEC1610_term

ADDRESS

ADDRESSØ=

ALLOFF

COM

HOT

COM

–

SHLD

SABUS

SENSOR

COM

–

PWR

OUT4

OCOM4

OUT5

OCOM5

OUT6

OCOM6

OUT7

OCOM7

OUT2

OCOM2

OUT1

OCOM1

OUT3

OCOM3

BINARY

IN3

ICOM

UNIVERSAL

+15V

IN1

ICOM

IN2

ICOM

EOL

SABUS

FAULT

POWER

TheBinaryOutput’sINT/EXTpowersourcejumpersarelocatedunderthe

FECcoverontheterminationboard.

Note:

FCBusTerminalsand

TerminalBlock

SABusTerminalsand

TerminalBlock

FEU16x0 Field Equipment Controller Installation Instructions

Mounting

Observe these guidelines when mounting a field controller:

• Ensure the mounting surface can support the controller, DIN rail, and any user-supplied enclosure.

• Mount the controller horizontally on 35 mm DIN rail whenever possible.

• Mount the controller in the proper orientation. If wall mount applications are not allowed for the FEU1610-0U,

then proper mounting position will only be as shown in Figure 2.

• Mount the controller on a hard, even surface whenever possible in wall mount applications.

• Use shims or washers to mount the unit securely and evenly on the mounting surface.

• Mount the controller in an area free of corrosive vapors and observe the Ambient Conditions requirements

listed in the Technical Specifications section.

• Provide for sufficient space around the controller for calbe and wire connections for easy cover removal and

good ventilation through the controller (50 mm [2 in.] minimum on the top, bottom, and front of the controller).

• Do not mount the controller on surfaces prone to vibration, such as duct work.

• Do not mount the controller in areas where electromagnetic emissions from other devices or wiring can

interfere with controller communication.

Observe these additional guidelines when mounting a controller in a panel or enclosure:

• Mount the controller so that the enclosure walls do not obstruct cover removal or ventilation through the

controller.

• Mount the controller so that the power transformer and other devices do not radiate excessive heat to the

controller.

• Do not install the controller in an airtight enclosure.

Wall Mount Applications

The FEU16 controller must be installed inside an FSCS panel; therefore, a wall mount application is not

acceptable.

DIN Rail Mount Applications

To mount the controller on a DIN rail inside the FSCS panel:

1. Securely mount a 20.3 cm (8 in.) or longer section of DIN rail horizontally and centered in the desired space so

that the controller mounts in the horizontal position shown in Figure 2.

2. Ensure that the bottom two mounting clips are pulled outward and snapped firmly into the extended position.

Figure 2: Required Orientation for DIN Rail Mount Applications

FIG:DINril

ADDRESS

ADDRESS Ø = ALL OFF

COM

HOT

–

SHLD

SA BUS

SENSOR

COM

–

PWR

OUT4

OCOM4

OUT5

OCOM 5

OUT6

OCOM6

OUT7

OCOM 7

OUT2

OCOM2

OUT1

OCOM1

OUT3

OCOM3

BI NA RY

IN3

ICOM

UNIVERSAL

+15V

IN1

ICOM

IN2

ICOM

EOL

SAB

FLT

PWR

ET SY

esc

FEU16x0 Field Equipment Controller Installation Instructions

3. Hand the controller by the hooks at the top of the DIN rail channel on the back of the controller, and position the

controller snugly against the DIN rail.

4. Push the bottom mounting clips inward (up) to secure the controller on the DIN rail tracks.

To remove the controller from the DIN rail, pull the bottom mounting clips out to the extended position and carefully

lift the controller off the DIN rail.

Wiring

For detailed information on configuring and wiring an MS/TP Bus, FC Bus, and SA Bus, refer to the MS/TP

Communications Bus Technical Bulletin (LIT-12011034).

Hard-Wired Installation

To install an FEU16 for hard-wired operation, perform the steps that follow. See Figure 1 for jack and terminal block

locations.

Input/Output Terminals

Terminate input/output point wiring at the controller per engineering drawings.

SA Bus Terminal Block and Sensor Port

Wire Network Sensors and other devices to the Sensor Actuator (SA) Bus terminal block (Figure 3) or Sensor port

(RJ-12 modular jack) for sensors.

Note: The FEU16 controller should be at one end of the SA Bus daisy chain. If multiple Input/Output Modules

(IOMs) are used, set the End-of-Line (EOL) switch on the last IOM.

Risk of Electric Shock: Disconnect the power supply before making electrical connections to avoid electric

shock.

Mise En Garde: Risque de décharge électrique: Débrancher l'alimentation avant de réaliser tout raccordement

électrique afin d'éviter tout risque de décharge électrique.

Risk of Property Damage: Do not apply power to the system before checking all wiring connections. Short

circuited or improperly connected wires may result in permanent damage to the equipment.

Mise En Garde: Risque de dégâts matériels: Ne pas mettre le système sous tension avant d'avoir vérifié tous

les raccords de câblage. Des fils formant un court-circuit ou connectés de façon incorrecte risquent

d'endommager irrémédiablement l'équipement.

IMPORTANT: Do not exceed the controller electrical ratings. Exceeding controller electrical ratings can result

in permanent damage to the controller and void any warranty.

IMPORTANT: Use copper conductors only. Make all wiring in accordance with local, national, and regional

regulations.

IMPORTANT: Electrostatic discharge can damage controller components. Use proper electrostatic discharge

precautions during installation, setup, and servicing to avoid damaging the controller.

FEU16x0 Field Equipment Controller Installation Instructions

FC Bus Terminal Block

Wire the Field Controller (FC) Bus in a daisy chain to other devices on the FC Bus and the supervisory controller

(Figure 4).

Note: The Shield terminal (SHLD) on the FC Bus terminal block is isolated and can be used as a convenient

terminal for connecting the bus cable shield (Figure 4).

Sensor Port

The Sensor Bus port on the bottom-right of the IOM is an RJ-12, 6-position modular jack that provides a connection

for an NS sensor. See Table 1 for more information. The Sensors Port pin assignment is shown in (Figure 5).

Device Address DIP Switches

Ensure the device address DIP switches are set to the appropriate address (in the range of 4-127). Ensure that DIP

switch 128 is set to Off, which disables wireless mode. For more details on setting the DIP switches, see the

Setting the FC Bus Address on page 11.

Figure 3: SA Bus Terminal Block Wiring

Figure 4: FC Bus Terminal Block Wiring

FEU16x0 Field Equipment Controller Installation Instructions

Supply Power Terminal Block

The 24 VAC supply power terminal block is a gray, removable, 3-terminal plug that fits into a board-mounted jack

on the top right of the controller. Connect the 24 VAC supply power wires from the transformer to the HOT and

COM terminals on the plug as shown in Figure 6. The middle terminal on the supply power block is not used..

IMPORTANT: The 24 VAC power should be connected to all network devices so transformer phasing is

uniform across the devices. Powering devices with uniform 24 VAC supply power phasing reduces noise,

interference, and ground loop problems. The FEC does not require an earth ground connection.

Figure 5: Pin Number Assignments for Sensor, SA Bus, and FC Bus Ports on FEC,

IOM, and VMA16

Power

(15 VDC)

SA or FC Bus +

SA or FC Bus

Bus and Power Common

Power

(15 VDC)

Sensor, SA Bus, or FC Bus Port

(RJ-12 Modular Jack)

Bus and Power Common

FIG:RJ_pinout

Figure 6: 24 VAC Supply Power Terminal Block Wiring

FEC

Supply Power

Terminal Block

FEC

Supply Power

Terminal Block

Plug

Wires from

Johnson Controls

24 VAC, Class 2

Power Transformer

Brown Wire

(COM)

Orange Wire

(24 VAC)

FIG:FEC_Pwer_Prt

24V~

COM

HOT

FEU16x0 Field Equipment Controller Installation Instructions

Wire Gauges and Lengths

See Table 1 for the field controller platform wiring list and Table 2 for alternative wire gauges and lengths.

Table 1: FEC Terminal Blocks, Functions, Ratings, Requirements, and Cables (Part 1 of 3)

Terminal

Block Terminal

Labels Function and Electrical Ratings/Requirements Recommended Cable Type

and Length1

Universal IN +15 V Provides 15 VDC power for active devices connected to

the Universal IN terminal blocks (3-wire connection).

35 mA total current

0.6 mm (22 AWG) stranded, 3-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

Same as IN. See IN ncable type.

IN nAnalog Input, Voltage Mode

Accepts a 0-10 VDC input signal.

10 VDC Maximum Input Voltage

Internal 75k ohm Pulldown

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Ain Table 2.)

Analog Input, Current Mode

Accepts a 4-20 mA input signal.

Note: For current sensing applications, the FEU16x0

does not provide a jumper to close the current loop when

the controller is powered off. This option is available on

FEC26x0 controllers only.

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable

(See Row Bin Table 2.)

Analog Input, Resistive Mode

Accepts 0-600k ohm input signal.

Internal 12 V, 15k ohm Pullup

RTD (1k Nickel [Johnson Controls], 1k Platinum, A99B

Silicon Temperature Sensor)

Negative Temperature Coefficient (NTC) Sensor

(10k Type L, 2.252k Type 2)

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Ain Table 2.)

Binary Input, Dry Contact Maintained Mode

1 second minimum pulse width (0.5 Hz at 50% duty cycle)

Internal 12 V, 15k ohm Pullup

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Ain Table 2.)

ICOM nThe signal common for all Universal IN terminals;

isolated from all other terminal commons 0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

Same as IN. See IN n cable type.

Note: Use 3-wire cable for active

devices that connect to the +15 V

terminal also.

Binary IN IN nBinary Input, Dry Contact Maintained Mode

0.01 second min. pulse width (50 Hz at 50% duty cycle)

Internal 8 V, 3.3k ohm Pullup

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Ain Table 2.)

Binary Input, Pulse Counter Mode

0.01 second min. pulse width (50 Hz at 50% duty cycle)

Internal 8 V, 3.3k ohm Pullup

ICOM nThe signal common for Binary IN terminals; isolated from

all other terminal commons, excluding Configurable

Output (CO) terminal commons that are configured as

Analog Outputs (AOs).

FEU16x0 Field Equipment Controller Installation Instructions

Binary OUT

(Jumper set

to External)

OUT nBinary Output, 24 VAC Triac

Connects OUT to OCOM when activated

30 VAC maximum output voltage

0.5 A maximum output current

1.3 A at 25% duty cycle

Maximum 6 cycles per hour with M9220-BGx-3

40 mA minimum load current

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Cin Table 2.)

OCOM nThe signal common for Binary OUT terminals; isolated

from all other terminal commons, including Binary Output

terminal commons

Binary OUT

(Jumper Set

to Internal)

OUT nSources 24 VAC Power (Hot) 0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Cin Table 2.)

OCOM nBinary Output, 24 VAC Triac

Connects OCOM to 24 VAC Power (Com) when activated

(low side switching).

30 VAC maximum output voltage

0.5 A maximum output current

40 mA minimum load current

Configurable

OUT OUT nAnalog Output, Voltage Mode

Sources 0-10 VDC

External 1k ohm minimum load required

10 VDC maximum output voltage

10 mA maximum output current

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Ain Table 2.)

Binary Output, 24 VAC Triac mode

Connects OUT to OCOM when activated.

30 VAC maximum output voltage

0.5 A maximum output current

1.3 A at 25% duty cycle

Maximum 6 cycles per hour with M9220-BGx-3

40 mA minimum load current

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(See Row Cin Table 2.)

OCOM nAnalog Output: The signal common for all analog CO

terminals; isolated from all other terminal commons,

excluding BI terminal commons

Binary Output: The signal common for binary-configured

CO terminals; isolated from all other terminal commons,

including other CO terminal commons

0.6 mm (22 AWG) stranded, 2-wire

twisted, non-shielded cable for

runs of <30 m (90 ft)

(Same as OUT. See OUT cable

type.)

Sensor2,3 Sensor Provides SA Bus communication network.

RJ-12 6-position modular connector 24 AWG 3-pair CAT 3 Cable

<30.5 m (100 ft)

SA Bus2,3+

-Provides SA Bus communication network. 0.6 mm (22 AWG) stranded, 4-wire

twisted, shielded cable

recommended

COM Provides reference for network communication bus and

15 VDC source power.

SA PWR Sources 15 VDC power for devices on the SA Bus

FC Bus

Terminal

Block3

COM

Provides FC Bus communication network. 0.6 mm (22 AWG) stranded, 3-wire

twisted, shielded cable

recommended

SHLD Provides an optional shield connection.

Table 1: FEC Terminal Blocks, Functions, Ratings, Requirements, and Cables (Part 2 of 3)

Terminal

Block Terminal

Labels Function and Electrical Ratings/Requirements Recommended Cable Type

and Length1

FEU16x0 Field Equipment Controller Installation Instructions

24~ Power Hot AC Supply Input

Supply 20-30 VAC (Nominal 24 VAC) 0.8 mm to 1.0 mm

(20 to 18 AWG) 2-wire

SHLD Provides an optional shield connection.

1. See Table 2 for alternative wire gauges and lengths.

2. The SA Bus terminals and the RJ-style modular Sensor Port are connected internally.

3. The SA Bus and FC Bus specifications in this table are for MS/TP bus communications at 38.4k baud. For more

information, refer to the MS/TP Communications Bus Technical Bulletin (LIT-12011034).

Table 2: Wire Gauge and Length Guidelines

Guideline Cable Size Maximum

Length Assumptions

A1.0 mm (18 AWG) 457.2 m (1,500 ft) 100 mV maximum voltage drop

0.8 mm (20 AWG) 297.2 m (975 ft)

0.6 mm (22 AWG) 182.9 m (600 ft)

0.5 mm (24 AWG) 106.7 m (350 ft)

B1.0 mm (18 AWG) 228.6 m (750 ft) 100 mV maximum voltage drop

0.8 mm (20 AWG) 137.1 m (450 ft)

0.6 mm (22 AWG) 91.4 m (300 ft)

0.5 mm (24 AWG) 61 m (200 ft)

CSee Figure 7.SeeFigure 7.N/A

Table 1: FEC Terminal Blocks, Functions, Ratings, Requirements, and Cables (Part 3 of 3)

Terminal

Block Terminal

Labels Function and Electrical Ratings/Requirements Recommended Cable Type

and Length1

FEU16x0 Field Equipment Controller Installation Instructions

Wiring Requirements

Use Figure 7 to determine the maximum wire length allowable when alternative wire gauges are required.

Setup and Adjustments

Determining the FC Bus Address

The FC Bus address switch sets a unique address for this controller on the FC Bus. You must set the FEC’s device

address for your field bus application.

Set consecutive device addresses 4 through 127 for Field Equipment Controllers and other master devices on the

FC Bus. Use sequential addressing with no gaps in the device address range to ensure best FC Bus performance.

Note: Switch 128 on the device address DIP switch block should be set to Off.

Table 3 shows and describes the valid FC Bus and SA Bus devices addresses for FECs and IOMs on Johnson

Controls® MS/TP communications bus applications.

Table 3: FC Bus Device Address Descriptions

Device

Address Description

0Reserved for FC Bus supervisory controller.

1-3 Reserved for peripheral devices.

4-127 Available for FECs on the FC bus and IOMs

on the SA or FC Bus.

128 Unused and should be set to Off.

129-255 Are not valid addresses for FEC or IOM

controllers on the SA or FC Bus.

Figure 7: Maximum Wire Length by Current and Wire Size

450 500

400

350

300

250

200150

100

0 m (0 ft)

15.2 m (50 ft)

30.5 m (100 ft)

45.7 m (150 ft)

61 m (200 ft)

76.2 m (250 ft)

91.4 m (300 ft)

106.7 m (350 ft)

121.9 m (400 ft)

137.2 m (450 ft)

Load Current (mA)

Length

FIG:wir_lngth

1.0 mm (18 AWG)

0.8 mm (20 AWG)

0.6 mm(22AWG)

0.5 mm (24 AWG )

Indice

Altri manuali Johnson Controls Controllori

Johnson Controls

Johnson Controls PENN P28 Manuale utente

Johnson Controls

Johnson Controls VMA1615 Manuale utente

Johnson Controls

Johnson Controls FX-PCA4911 Manuale utente

Johnson Controls

Johnson Controls VA9300 Manuale utente

Johnson Controls

Johnson Controls EDA-8100 Istruzioni per il montaggio

Johnson Controls

Johnson Controls FMS-1655 Series Manuale utente

Johnson Controls

Johnson Controls VA-77 Series Manuale utente

Johnson Controls

Johnson Controls METASYS ASC Manuale utente

Johnson Controls

Johnson Controls VA-8122 Manuale di servizio

Johnson Controls

Johnson Controls Metasys FAC4911 Manuale utente

Johnson Controls

Johnson Controls FEU2610 Series Manuale utente

Johnson Controls

Johnson Controls VA9208-AG Series Manuale utente

Johnson Controls

Johnson Controls UNT1100 Series Manuale utente

Johnson Controls

Johnson Controls M9102 GA-1S Series Manuale utente

Johnson Controls

Johnson Controls FEC1611 Manuale utente

Johnson Controls

Johnson Controls VFD66 Series Manuale

Johnson Controls

Johnson Controls G670 Istruzioni per il montaggio

Johnson Controls

Johnson Controls FX70 Manuale utente

Johnson Controls

Johnson Controls EDA-8102 Istruzioni per il montaggio

Johnson Controls

Johnson Controls M4-CV Series Manuale utente

Johnson Controls

Johnson Controls Hitachi C4IRK01 Manuale utente

Johnson Controls

Johnson Controls FX-PCG26 Manuale utente

Johnson Controls

Johnson Controls M9102-GA-1S Series Manuale utente

Johnson Controls

Johnson Controls VA9204-GG-2Z Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente