Johnson Controls P2000 Manuale
24-10707-112 Revision D
December 2017
P2000
Security Management System
CKM-CE75-E1M
enclosure with power supply
hardware
installation
Copyright 2017
Johnson Controls
All Rights Reserved
No part of this document may be reproduced without the prior permission of Johnson Controls.
If this document is translated from the original English version by Johnson Controls, all reasonable
endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable
for any translation errors contained herein or for incidental or consequential damages in connection
with the furnishing or use of this translated material.
Due to continuous development of our products, the information in this document is subject to
change without notice. Johnson Controls shall not be liable for errors contained herein or for
incidental or consequential damages in connection with furnishing or use of this material. Contents
of this publication may be preliminary and/or may be changed at any time without any obligation to
notify anyone of such revision or change, and shall not be regarded as a warranty.
Other Manufacturers’ Documentation
Johnson Controls does not duplicate documentation of other equipment manufacturers. When
necessary, Johnson Controls provides documentation that supplements that of other manufacturers.
When unpacking equipment, keep all original manufacturer documentation for future reference.
Technical Support
For factory technical support, Johnson Controls authorized field technicians or authorized dealer
representatives can contact Global Security Solutions Technical Support by phone at
can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.
End users and customers should contact their local Johnson Controls branch or authorized dealer
for any of their support needs (technical support, maintenance contracts, on-site field support,
P2000 Software Service Agreements, Service Partnerships, and so on). Visit
http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.
For material returns contact the branch if the material was purchased through a Johnson Controls
branch or through the Product Sales Operations Team, if ordered through the Advanced Order
Management System (AOMS) and follow the RMA process; or contact the authorized dealer
representative where the material was purchased directly.
Acknowledgments
Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and
product names are trademarks or registered trademarks of their respective owners.
Declaration of Conformity
United States: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Canada: CAN ICES-3 (A)/NMB-3(A)
European Union: This product complies with the requirements of the EMC Directive and the Low
Voltage Directive.
This equipment must not be modified for any reason and it must be installed as stated in the
Manufacturer’s instructions. If this shipment (or any part thereof) is supplied as second-hand
equipment, equipment for sale outside the European Economic Area or as spare parts for either a
single unit or system, it is not covered by the Directives.
UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET
The following model number is listed under Underwriters Laboratories® (UL) 1076 for Proprietary
Burglar Alarm Units and Systems, UL 294 for Access Control Systems Units and Underwriters
Laboratories of Canada ULC/ORD-C1076-86.
CKM-CE75-E1M
When installed at the site the following requirements must be met to comply with these standards.
1. The CKM-CE75-E1M must be installed within the protected premise.
2. The CKM-CE75-E1M may be used with Models CKM-EP1501, CKM-MR51E, CKM-MR50,
and CKM-MR50-S3 found in file BP4166, Vol. 2, Sec. 9.
3. Power to Models CKM-EP1501, CKM-MR51E, CKM-MR50, and CKM-MR50-S3 shall be
provided via Listed Model F8P.
4. Four hours of standby power for the CKM-CE75-E1M shall be provided by Listed EB-80
battery box and minimum one 12 VDC, 40Ah sealed lead acid battery.
5. CKM-CE75-E1M battery output connections BAT+ and BAT- must be connected to battery via
LifeSafety Power Listed Model BDM (Battery Disconnect Module).
6. The CKM-CE75-E1M must be mounted within 6 feet of the Listed EB-80 battery box.
7. The power supply BAT DET jumper must be installed.
8. The power supply SYS FLT signal must be connected to a Listed subassembly input point
within the same room, not exceeding 100 ft., and enabled at all times
9. The power supply AC FLT signal must be connected to a Listed subassembly input point
within the same room, not exceeding 100 ft., and enabled at all times.
10. If used, the power supply FAI signal must be connected to a Listed subassembly input point
within the same room, not exceeding 100 ft.
11. The NL1 network module has not been investigated for use with the CKM-CE75-E1M.
12. The tamper switch must be connected to a Listed subassembly and enabled at all times
13. Transient protection devices that are installed must not be removed or defeated.
14. Do not connect equipment to an AC power source that is controlled by a switch.
15. UL 294 Performance Levels
Destructive Attack Level I
Endurance Level IV
Line Security Level I
Standby Power Level IV
CKM-CE75-E1M Table of Contents
24-10707-112 Rev. D
i
TABLE OF CONTENTS
Chapter 1: Introduction
Manual Summary 1-1
Important Installation Information 1-1
FlexPower Power Management System Standard Features 1-2
Chapter 2: Hardware Information
12 in. by 14 in. Enclosure 2-1
CKM-FPO75 Power Supply 2-2
Chapter 3: Installation and Wiring
Enclosure Mounting Information 3-1
Wiring Information 3-2
AC Wiring 3-3
Connecting to Standby Power 3-4
Battery Wiring 3-5
Additional Installation Guidelines 3-6
Mounting CKM Devices 3-6
Tamper Switch Wiring 3-10
Chapter 4: Fire Alarm Interface Input
Chapter 5: Operations and Maintenance
Powering Up and Basic System Verification 5-1
Maintenance Procedures 5-2
Appendix A: Troubleshooting
CKM-CE75-E1M Table of Contents
24-10707-112 Rev. D
ii
CKM-CE75-E1M Introduction
24-10707-112 Rev. D
1-1
1. INTRODUCTION
Use the information in this manual to install, wire, and maintain the
CKM-CE75-E1M enclosure with power supply.
MANUAL SUMMARY
This document consists of the following chapters and appendix:
•Chapter 1: Introduction, describes the scope of this manual, lists important
warnings and cautions, and describes standard features of the FlexPower
Power Management System.
•Chapter 2: Hardware Information, provides hardware information for the
CKM-FPO75-E1M enclosure with power supply.
•Chapter 3: Installation and Wiring, provides detailed mounting and wiring
information.
•Chapter 4: Fire Alarm Interface Input, provides instructions about the Fire
Alarm Interface (FAI) input.
•Chapter 5: Operations and Maintenance, provides instructions for powering
up, basic system verification, and maintenance.
•Appendix A: Troubleshooting, provides a list of problem conditions, their
possible causes, and suggested solutions.
IMPORTANT INSTALLATION INFORMATION
Observe the following installation notes:
• Perform the installation only if you are a member of qualified service
personnel.
• Conform to all local codes.
• Install equipment in a manner that prevents unintentional operation by
employees, cleaning personnel, or others working in the premises, as well
as by falling objects, customers, building vibration, or similar causes.
• To ensure proper operation, test the system and any batteries at least once
per year.
CKM-CE75-E1M Introduction
24-10707-112 Rev. D
1-2
IMPORTANT: To prevent premature loss of battery power, maintain batteries at an
ambient temperature of between 32 and 120°F (0–49°C).
IMPORTANT: Ensure that all wiring is routed and secured to prevent accidental
open or short circuit conditions.
IMPORTANT: Replace fuses only with fuses of the same type and rating.
FLEXPOWER POWER MANAGEMENT SYSTEM STANDARD FEATURES
FlexPower’s advanced feature set provides greater product reliability, increased
flexibility, shorter installation time, a smaller service inventory, and an
intelligent, economical solution to the problem of reliable system power:
• VSelect®
A single switch for configuring the output between 12 and 24 VDC
eliminates field errors and helps reduce and simplify service inventory by
eliminating the need to stock units in each voltage.
• TruWatt®
The output power capability of the power supply remains constant
regardless of the output voltage setting.For example, a FlexPower 150 watt
supply provides 6 amperes at 24 VDC and 12 amperes at 12 VDC, allowing
you to use the same number of locking devices at either setting.
WARNING: Risk of Electric Shock or Fire.
Do not expose this equipment to rain or moisture. Doing so may
result in electric shock or fire.
CAUTION: Risk of Damage to the System and Voided
Warranty.
Do not use the power supply with a 230 VAC input unless the
input voltage selection jumper (JP1) is cut and removed. Failure
to cut and remove the jumper may cause damage to the system
and will void the warranty.
!
!
CKM-CE75-E1M Introduction
24-10707-112 Rev. D
1-3
• SureCharge®
The microprocessor-controlled charging process used by FlexPower
guarantees the proper charging current for the battery and the fastest charge
time. The constant current charger provides a linear, predictable charge
time for any battery set from one at 40 ampere/hours to four at 40 ampere/
hours, depending on the model, without stress or damage to the battery.
• DataLink®
Smart power management communication interface. Program, monitor,
control and report key power supply functions by computer or over a local
or wide area network using a browser interface or LifeSafety Power’s
Remote Management Software.
DataLink computer connectivity requires an optional DL1 USB cable.
DataLink WAN/LAN connectivity requires an optional NL1 network
module.
• PowerCom®
The PowerCom power management software monitors, programs, and
reports on the power supply core functions through a computer or network
connection. See the PowerCom manual for complete details on
FlexPower’s power management capabilities.
• FlexConnect®
The FlexPower series provides a pre-wired interconnection system between
the power supplies and accessory boards of the power system that
eliminates inter-module wiring by the field installer. Field upgrading uses
common mounting footprints, predrilled mounting holes, snap-in standoffs,
and pluggable wires to add additional system capability or capacity when
needed.
• Reliability+®
All power supplies within the FlexPower system are fully fault protected.
• GreenSmart®
All members of the FlexPower family are RoHS compliant, lead-free, and
meet the latest federal and European requirements for energy efficiency.
CKM-CE75-E1M Introduction
24-10707-112 Rev. D
1-4
Altri manuali per P2000
6
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Johnson Controls Allegato
