Johnson Controls Simplicity LINC Guida utente

1031990-UAD-A-0313

APPLICATION GUIDE

OVERVIEW

The Simplicity®LINC Gateway operates as a Modbus® Client

providing an interface between a BACnet® MS/TP control system

and devices that communicate using the Modbus RTU protocol.

The Simplicity®LINC allows monitoring and control by a third-party

BACnet Building Automation System (BAS).

The Simplicity®LINC is preconfigured to provide an interface to UP

products equipped with Simplicity®controllers manufactured after

4/2/2008 as well as prior Simplicity®Elite™ and Simplicity®with

Intelli-Comfort™ controllers.

The Simplicity®LINC mounts inside the control panel of the UP

unit and utilizes 24 VAC power from the unit’s control transformer.

One port is connected to the UP controller. The other port must be

connected to the BACnet MS/TP network.

The Simplicity®LINC Gateway is preconfigured to obtain

operational data points from the controller and expose them on a

BACnet MS/TP network.

NOTE: Not all Simplicity®operating parameters are controlled/

monitored by the Simplicity®LINC.

FIGURE 1: WIRE CONNECTIONS

24 — must be grounded

close to the Simplicity LINC

The shield must be

connected to ground at

each device.

24V power is polarity sensitive, incorrect

wiring could result in board damage.

Simplicity®LINC GATEWAY

ConFig v1.01d

1031990-UAD-A-0313

2 Johnson Controls Unitary Products

CONNECTION

The Simplicity®LINC has 2 ports, one for connection to the BAS

network (BACnet) and one to the Simplicity®board (Modbus).

BACNET NETWORK

The only connection required in the field is to the BACnet (BAS)

network.

NOTE: Proper termination and grounding of the shields must

be observed.

DIP switches A0-A7 on the Simplicity®LINC board allow

selection of the MAC Address. The MAC Address identifies the

Simplicity®LINC to other devices and must be between 1 and

99. The default DIP switch setting is 1.

A Device Instance (DE) Modifier is used by the Simplicity®LINC

and defaulted to 230. The combination of the DE Modifier and

the default DIP switch setting creates a default DE of 23001.

The default Unit Name is YORK_RTU.

FIGURE 2: MAC ADDRESS EXAMPLES

DIP switches B0-B3 on the Simplicity®LINC board allow for

selection of the BACnet transfer speed.The default speed is set

at 38.4k baud. Other speeds can be chosen as shown in Table

MAC Address of 21

MAC Address of 99

128

1 2 3 4 5 6 7 8

128

1 2 3 4 5 6 7 8

TABLE 1: BAUD RATE SELECTION SETTINGS

DIP Setting Baud Rate

1 110

2 300

3 600

4 1200

5 2400

6 4800

7 9600

8 19200

9 20833

10 28800

11(Default) 38400

12 57600

13 76800

14 115200

1 2 3 4

Baud Rate of 38400

1031990-UAD-A-0313

Johnson Controls Unitary Products 3

MODBUS CONNECTION

The UP device communicates with the Simplicity®LINC using

the Modbus RTU protocol on an RS485 connection. Connection

and addressing of the UP product is completed at the factory.

No further adjustment should be done.

If a problem arises with the Simplicity®LINC or a parameter not

exposed by the Simplicity®LINC requires modification, the UP

controller software can be manipulated using a Microsoft©

Windows-based PC with the Simplicity®PC software

(downloadable from the UP website). To connect the PC to the

UP controller, a FREEnet USB adaptor (Part No.

S103101967000), which is an RS232 to RS485 adapter, and

FREEnet adapter cable (S102538682000) are required and

available through SOURCE1 (Toll-free at 1-800-536-6112).

SOFTWARE SETUP

The control sequence is managed by the Simplicity®controller.

The data points on these systems are mapped to standard

BACnet Objects. As a preconfigured application, no

configuration is necessary in the Simplicity®LINC Gateway.

FLASH MEMORY MANAGEMENT

The Flash Memory chip used in the Simplicity®controllers has

a 1,000,000 write cycle rating.

To prevent premature failure of the flash memory, it should not

be written to more often than once every 10 minutes, on

average.

The default Simplicity®board address is 1 and must

remain on address 1 to correctly communicate with

Simplicity®LINC. To change the address to 1, press the

Com/Setup button 3 times in succession.

Under unusual circumstances it could take up to two

minutes for newly updated data to be seen.

This product has been

tested at a qualified BACnet

testing laboratory and

found to comply with all the

necessary interoperability

requirements.

1031990-UAD-A-0313

4 Johnson Controls Unitary Products

TABLE 2: POINTS LIST IN DESCRIPTION ORDER

Read/

Write

BACnet

Object

Type

BACnet

Object

Inst Descriptor Default Min Max Point Description

R / W (5) BV 109 COMM_IAQ n/a n/a n/a Accept Comm Value for Indoor Quality

Sensor

R / W (5) BV 101 COMM_OAT n/a n/a n/a Accept Comm Value for OAT

R / W (5) BV 100 COMM_OH n/a n/a n/a Accept Comm Value for OH

R / W (5) BV 99 COMM_RH n/a n/a n/a Accept Comm Value for RH

R / W (5) BV 108 COMM_ST n/a n/a n/a Accept Comm Value for Space

Temperature

R / W (2) AV 14 ACC_OVER_TME n/a n/a n/a Accumulated Unoccupied Override

Time (in hours)

R (2) AI 15 ACTIVE_ALARM n/a n/a n/a Active Alarm

R (2) AI 86 AIR_MON_INPUT 0 0 10 Air Monitor Station Input

R (5) BI 16 AIR_PROOF_SW n/a n/a n/a Air Proving Switch Status (1=closed,

0=open / no air flow)

R / W (2) AV 79 OAQ_STPT 1000 0 5000 Air Quality Setpoint Outside

R (5) BI 85 ALARM_1_ON n/a n/a n/a Alarm Buffer #1 (0=Alarm has cleared,

1=Alarm is still active)

R (5) BI 86 ALARM_2_ON n/a n/a n/a Alarm Buffer #2 (0=Alarm has cleared,

1=Alarm is still active)

R (5) BI 87 ALARM_3_ON n/a n/a n/a Alarm Buffer #3 (0=Alarm has cleared,

1=Alarm is still active)

R (5) BI 88 ALARM_4_ON n/a n/a n/a Alarm Buffer #4 (0=Alarm has cleared,

1=Alarm is still active)

R (5) BI 89 ALARM_5_ON n/a n/a n/a Alarm Buffer #5 (0=Alarm has cleared,

1=Alarm is still active)

R (2) AI 33 BLDG_STATIC n/a n/a n/a Building Static Pressure

R / W (5) BV 29 BP_SENS_INST n/a n/a n/a Building Static Pressure Sensor

Installed

R / W (2) AV 57 BLDG_SP_STPT 0.15 -0.25 0.25 Building Static Pressure Setpoint

R / W (2) AV 25 COM_V_LOW_SP 70 60 80 Comfort Ventilation LowerSetpoint

(degrees F)

R / W (5) BV 34 CVM_COOLING n/a n/a n/a Comfort Ventilation Mode for Cooling

Enabled

R / W (5) BV 35 CVM_HEATING n/a n/a n/a Comfort Ventilation Mode for Heating

Enabled

R (5) BI 33 COM_VENT_STA n/a n/a n/a Comfort Ventilation Mode Status

(1=control is in Comfort Vent mode, 0= it

is not)

R / W (2) AV 24 COM_V_HI_SP 80 65 85 Comfort Ventilation Upper Setpoint

(degrees F)

R / W (5) BV 23 COOLING_ENA n/a n/a n/a Cooling Mode Enabled

R (2) AI 56 CV_VAV_SELEC n/a n/a n/a CV / VAV Selected (0= Valid CV,

1=Valid VAV, 2= Invalid Value)

R / W (5) BV 21 FAN_ON_W_SEN n/a n/a n/a CV-Indoor Fan Operates with Space

Sensor Present Option Enabled

R / W (2) AV 8 IAQ_VALUE n/a 0 5000 Demand Ventilation (IAQ) Value (PPM)

1031990-UAD-A-0313

Johnson Controls Unitary Products 5

R / W (5) BV 39 DEMAND_VENT n/a n/a n/a Demand Ventilation (using Inside

Sensor) Enabled

R / W (2) AV 18 DEMVENT_STPT 1000 0 5000 Demand Ventilation Setpoint

R (2) AI 67 REVISION n/a n/a xx Device Revision

R / W (5) BV 98 DIFF_ENTH_MODE n/a n/a n/a Differential enthalpy mode enabled

R / W (5) BV 90 DF_SW_INST n/a n/a n/a Dirty Filter Switch Installed

R (5) BI 15 DIRT_FILT_SW n/a n/a n/a Dirty Filter Switch Status

(0=open,1=closed / fault)

R (2) AI 35 DUCT_STATIC n/a n/a n/a Duct Static Pressure

R / W (2) AV 58 DUCT_SP_STPT 1.5 0 5 Duct Static Pressure Setpoint

R / W (2) AV 59 DUCT_SD_STPT 4.5 0 5 Duct Static Pressure Shutdown Setpoint

R / W (2) AV 87 ECON_MIN_POS_LP 25 0 100 Econ Minimum Position For Low Speed

Fan

R (2) AI 31 ECO_DAMP_OUT n/a n/a n/a Economizer Damper Output Status (0-

100%)

R / W (2) AV 20 ECO_1ST_STPT 55 40 65 Economizer First Stage Setpoint

R / W (5) BV 7 ECONO_INST n/a n/a n/a Economizer Installed

R / W (5) BV 36 ECO_L_TO_SAT n/a n/a n/a Economizer Loading to Control Supply

Air Temperature Enabled

R / W (2) AV 19 ECON_MIN_POS 20 0 100 Economizer Minimum Position

R (5) BI 31 ECONO_STATUS n/a n/a n/a Economizer Output Status (0=not Free

Cooling, 1= Free Cooling)

R / W (2) AV 22 ECON_OAEN_SP 27 10 50 Economizer Outside Air Enthalpy

Setpoint

R / W (2) AV 23 ECON_OAT_ENA 55 40 80 Economizer Outside Air Temperature

Enable Setpoint

R / W (2) AV 84 ECON_RAEN_SP 27 10 50 Economizer Return Air Enthalpy

Setpoint

R / W (2) AV 21 ECO_2ND_STPT 50 40 65 Economizer Second Stage Setpoint

R (2) AI 41 E_C1_ACM_HRS n/a n/a n/a Elite Compressor #1 Accumulated Run

Time (in hours)

R (5) BI 42 E_COMP1_STAT n/a n/a n/a Elite Compressor #1 Output Status

(0=output is OFF, 1=output is ON)

R (5) BI 45 E_C1_OVRLOAD n/a n/a n/a Elite Compressor #1 Overload Switch

Input Status (1=closed, 0=open / fault)

R (2) AI 42 E_C2_ACM_HRS n/a n/a n/a Elite Compressor #2 Accumulated Run

Time (in hours)

R (5) BI 46 E_COMP2_STAT n/a n/a n/a Elite Compressor #2 Output Status

(0=output is OFF, 1=output is ON)

R (5) BI 49 E_C2_OVRLOAD n/a n/a n/a Elite Compressor #2 Overload Switch

Input Status (1=closed, 0=open / fault)

R (2) AI 43 E_C3_ACM_HRS n/a n/a n/a Elite Compressor #3 Accumulated Run

Time (in hours)

R (5) BI 51 E_COMP3_STAT n/a n/a n/a Elite Compressor #3 Output Status

(0=output is OFF, 1=output is ON)

TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)

Read/

Write

BACnet

Object

Type

BACnet

Object

Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313

6 Johnson Controls Unitary Products

R (5) BI 54 E_C3_OVRLOAD n/a n/a n/a Elite Compressor #3 Overload Switch

Input Status (1=closed, 0=open / fault)

R (2) AI 44 E_C4_ACM_HRS n/a n/a n/a Elite Compressor #4 Accumulated Run

Time (in hours)

R (5) BI 55 E_ COMP4_STAT n/a n/a n/a Elite Compressor #4 Output Status

(0=output is OFF, 1=output is ON)

R (5) BI 58 E_C4_OVRLOAD n/a n/a n/a Elite Compressor #4 Overload Switch

Input Status (1=closed, 0=open / fault)

R (5) BI 50 E_CFAN1_STAT n/a n/a n/a Elite Condenser Fan #1 Output Status

(0=output is OFF, 1=output is ON)

R (5) BI 59 E_CFAN2_STAT n/a n/a n/a Elite Condenser Fan #2 Output Status

Input Status (0=output is OFF, 1=output

is ON)

R (5) BI 41 E_FAN_ OVER n/a n/a n/a Elite Fan Overload Switch Input Status

(1=closed, 0=open / fault)

R (5) BI 60 E_GAS_VLVE1 n/a n/a n/a Elite Gas Valve #1 Input Status

(1=energized, 0=not energized)

R (5) BI 62 E_GAS_VLVE2 n/a n/a n/a Elite Gas Valve #2 Input Status

(1=energized, 0=not energized)

R (5) BI 64 E_GAS_VLVE3 n/a n/a n/a Elite Gas Valve #3 Input Status

(1=energized, 0=not energized)

R (5) BI 44 E_HPS1 n/a n/a n/a Elite High Pressure Switch for

Compressor #1 Input Status (1=closed,

0=open / fault)

R (5) BI 48 E_HPS2 n/a n/a n/a Elite High Pressure Switch for

Compressor #2 Input Status (1=closed,

0=open / fault)

R (5) BI 53 E_HPS3 n/a n/a n/a Elite High Pressure Switch for

Compressor #3 Input Status (1=closed,

0=open / fault)

R (5) BI 57 E_HPS4 n/a n/a n/a Elite High Pressure Switch for

Compressor #4 Input Status (1=closed,

0=open / fault)

R (5) BI 40 E_IFAN_STAT n/a n/a n/a Elite Indoor Fan Output Status

(0=output is OFF, 1=output is ON)

R (5) BI 61 E_LIMIT_ 1 n/a n/a n/a Elite Limit Switch #1 Input Status

(1=closed, 0=open / fault)

R (5) BI 63 E_LIMIT_ 2 n/a n/a n/a Elite Limit Switch #2 Input Status

(1=closed, 0=open / fault)

R (5) BI 65 E_LIMIT_ 3 n/a n/a n/a Elite Limit Switch #3 Input Status

(1=closed, 0=open / fault)

R (5) BI 43 E_LPS1 n/a n/a n/a Elite Low Pressure Switch for

Compressor #1 Input Status (1=closed,

0=open / fault)

TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)

Read/

Write

BACnet

Object

Type

BACnet

Object

Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313

Johnson Controls Unitary Products 7

R (5) BI 47 E_LPS2 n/a n/a n/a Elite Low Pressure Switch for

Compressor #2 Input Status (1=closed,

0=open / fault)

R (5) BI 52 E_LPS3 n/a n/a n/a Elite Low Pressure Switch for

Compressor #3 Input Status (1=closed,

0=open / fault)

R (5) BI 56 E_LPS4 n/a n/a n/a Elite Low Pressure Switch for

Compressor #4 Input Status (1=closed,

0=open / fault)

R (2) AI 32 EXH_DAMP_OUT n/a n/a n/a Exhaust Damper Output Status (0-

100%)

R (5) BI 30 EX_FAN_STAT n/a n/a n/a Exhaust Fan Output Status (0=output is

OFF, 1=output is ON)

R / W (5) BV 10 EX_VFD_INST n/a n/a n/a Exhaust VFD Installed

R / W (2) AV 91 FAN_SPD_1ST_COOL 70 0 100 Fan Speed: 1st Stage Cooling

R / W (2) AV 92 FAN_SPD_1ST_HEAT 100 0 100 Fan Speed: 1st Stage Heating

R / W (2) AV 93 FAN_SPD_ALL_COOL 100 0 100 Fan Speed: All Stages Cooling

R / W (2) AV 94 FAN_SPD_ALL_HEAT 100 0 100 Fan Speed: All Stages Heating

R / W (2) AV 90 FAN_SPD_NO_HEAT_COOL 50 0 100 Fan Speed: No Heating No Cooling

R (5) BI 102 4_STG_EXP_PRES n/a n/a n/a Four Stage Expansion board Present

R (5) BI 32 FRECOOL_STAT n/a n/a n/a Free Cooling Mode Status (0=comps

not overridden by Econo, 1=comps

overridden)

R (5) BI 104 FREEZE_STAT_1 n/a n/a n/a Freeze Stat # 1

R (5) BI 105 FREEZE_STAT_2 n/a n/a n/a Freeze Stat # 2

R (5) BI 106 FREEZE_STAT_3 n/a n/a n/a Freeze Stat # 3

R (5) BI 107 FREEZE_STAT_4 n/a n/a n/a Freeze Stat # 4

R (5) BI 68 HEAT_1_STAT n/a n/a n/a H1 Heating Output #1 Status (0=output

is OFF, 1=output is ON)

R (5) BI 69 HEAT_2_STAT n/a n/a n/a H2 Heating Output #2 Status (0=output

is OFF, 1=output is ON)

R (5) BI 70 HEAT_3_STAT n/a n/a n/a H3 Heating Output #3 Status (0=output

is OFF, 1=output is ON)

R (2) AI 76 H1_ACCUM_HRS n/a n/a n/a Heating #1 Accumulated Run Time (in

hours)

R (2) AI 77 H2_ACCUM_HRS n/a n/a n/a Heating #2 Accumulated Run Time (in

hours)

R (2) AI 78 H3_ACCUM_HRS n/a n/a n/a Heating #3 Accumulated Run Time (in

hours)

R / W (5) BV 25 HEATING_ENA n/a n/a n/a Heating Mode Enabled

R / W (2) AV 27 HGR_HUM_STPT 50 0 100 Hot Gas Reheat Humidity Setpoint

(percent Humidity)

R (5) BI 18 HGR_STAT n/a n/a n/a Hot Gas Reheat Output Status

(0=output is OFF, 1=output is ON)

TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)

Read/

Write

BACnet

Object

Type

BACnet

Object

Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313

8 Johnson Controls Unitary Products

R (2) AI 47 HGR_VLV_OUT n/a n/a n/a Hot Gas Reheat Valve Output Status (0-

100%)

R (5) BI 66 E_FREEZE_ST n/a n/a n/a Hot H2O Freeze Thermostat Switch

Input Status (1=closed, 0=open / fault)

R (2) AI 55 HW_VLV_OUT n/a n/a n/a Hot Water Valve Output Status (0-

100%)

R / W (5) BV 2 HYDRONC_HEAT n/a n/a n/a Hydronic Heat Enabled

R / W (5) BV 3 HH_REVER_VLV n/a n/a n/a Hydronic Heat Reverse Actuated Valve

Installed

R / W (2) AV 62 HYD_S1_SA_SP 120 80 180 Hydronic Heating Stage #1 Supply Air

Setpoint (degrees F)

R / W (2) AV 63 HYD_S2_SA_SP 150 81 180 Hydronic Heating Stage #2 Supply Air

Setpoint (degrees F)

R / W (2) AV 80 IO_DVNT_STPT 700 0 2000 Indoor / Outdoor Demand Ventilation

Setpoint

R (2) AI 45 I_C1_ACM_HRS n/a n/a n/a Intelli-Comfort Compressor #1

Accumulated Run Time (in hours)

R (5) BI 73 I_COMP1_STAT n/a n/a n/a Intelli-Comfort Compressor #1 Input

Status (0=output is OFF, 1=output is

ON)

R (2) AI 46 I_C2_ACM_HRS n/a n/a n/a Intelli-Comfort Compressor #2

Accumulated Run Time (in hours)

R (5) BI 76 I_COMP2_STAT n/a n/a n/a Intelli-Comfort Compressor #2 Input

Status (0=output is OFF, 1=output is

ON)

R (5) BI 79 I_CFAN_STAT n/a n/a n/a Intelli-Comfort Condenser Fan #1 Input

Status (0=output is OFF, 1=output is

ON)

R (5) BI 72 I_FAN_OVER n/a n/a n/a Intelli-Comfort Fan Overload Switch

Input Status (0=open,1=closed)

R (5) BI 82 I_FREEZE_1 n/a n/a n/a Intelli-Comfort Freeze Thermostat

Switch #1 Input Status

(0=open,1=closed)

R (5) BI 83 I_FREEZE_2 n/a n/a n/a Intelli-Comfort Freeze Thermostat

Switch #2 Input Status

(0=open,1=closed)

R (5) BI 80 I_GAS_VLVE1 n/a n/a n/a Intelli-Comfort Gas Valve #1 Input

Status

R (5) BI 75 I_HPS1 n/a n/a n/a Intelli-Comfort High Pressure Switch for

Compressor #1 Input Status (1=closed,

0=open / fault)

R (5) BI 78 I_HPS2 n/a n/a n/a Intelli-Comfort High Pressure Switch for

Compressor #2 Input Status (1=closed,

0=open / fault)

R (5) BI 71 I_IFAN_STAT n/a n/a n/a Intelli-Comfort Indoor Fan Output Status

(0=output is OFF, 1=output is ON)

TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)

Read/

Write

BACnet

Object

Type

BACnet

Object

Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313

Johnson Controls Unitary Products 9

R (5) BI 81 I_LIMIT_1 n/a n/a n/a Intelli-Comfort Limit Switch #1 Input

Status

R (5) BI 74 I_LPS1 n/a n/a n/a Intelli-Comfort Low Pressure Switch for

Compressor #1 Input Status (1=closed,

0=open / fault)

R (5) BI 77 I_LPS2 n/a n/a n/a Intelli-Comfort Low Pressure Switch for

Compressor #2 Input Status (1=closed,

0=open / fault)

R / W (5) BV 28 INTELLI-STRT n/a n/a n/a Intelli-Start Enabled

R / W (5) BV 13 LOADSHED n/a n/a n/a Loadshed (0=clear loadshed, 1=set

loadshed operation)

R / W (2) AV 89 LOW_AMB_ECON_MIN 0 0 99 Low Ambient Economizer Minimum

Position (Percent) (0 disables)

R / W (2) AV 88 LOW_AMB_ECON_STPT 0 0 60 Low Ambient Economizer Temperature

Setpoint (0 disables)

R / W (5) BV 19 LOW_AMB_OVRD n/a n/a n/a Low Ambient Temperature (0=comps

not overridden by LAT, 1=comps

overridden)

R (5) BI 14 LOW_SUP_VOLT n/a n/a n/a Low Supply Voltage (0=comps not

overridden by LSV, 1=comps

overridden)

R / W (2) AV 28 MAX_TH_OFSET 3 0 5 Max Temperature / Humidity Setpoint

Offset

R / W (2) AV 30 MAX_DMV_ECON 50 0 100 Maximum Demand Ventillation

Economizer Position

R / W (5) BV 110 MIN_AMB_SEN n/a n/a n/a Minimum Outdoor Air Sensor Enabled

R / W (2) AV 85 MIN_AMB_TEMP_SP 0 0 100% Minimum Outdoor Air Temperature

Setpoint (0-100%)

R (5) BI 11 MODBUS_ALARM n/a n/a n/a Modbus Communication Alarm

R / W (5) BV 9 MOD_EX_INST n/a n/a n/a Modulating Exhaust Installed

R / W (2) AV 61 MWU_RAT_STPT 70 50 85 Morning Warm-Up and VAV Heating:

Return Air Temperature Setpoint

(degrees F)

R / W (5) BV 6 MORN_WARM-UP n/a n/a n/a Morning Warm-Up Enabled

R (2) AI 16 NUMBER_COMPS 2 4 Number of Compressors Available

R (2) AI 48 NUMBER_HEAT n/a n/a n/a Number of Heat Stages Available (0,0, 0

stage, 0,1= 1 stage, 1,0= 2 stage, 1,1= 3

stage)

R / W (2) AV 1 OCC_COOL_SP 72 46 99 Occupied Cooling Setpoint

R / W (2) AV 50 OCC_HEAT_SP 68 45 98 Occupied Heating Setpoint

R / W (5) BV 1 OCCUPIED_ENA n/a n/a n/a Occupied Input Enabled

R / W (5) BV 93 OCC_COMS_ENA n/a n/a n/a Occupied Thermostat or

Communication Input Enabled

R (2) AI 17 OP_COOL_STPT n/a n/a n/a Operating Cooling Setpoint

R (2) AI 49 OP_HEAT_STPT 68 45 99 Operating Heating Setpoint

TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)

Read/

Write

BACnet

Object

Type

BACnet

Object

Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313

10 Johnson Controls Unitary Products

R / W (2) AV 69 OP_STPT_DIF 1 1 5 Operating Setpoint Differential

R / W (2) AV 74 OAT_COOL_L_O 45 0 100 Outdoor Air Temperature Cooling

Lockout Temperature

R / W (2) AV 54 OAT_HEAT_L_O 75 0 100 Outdoor Air Temperature

HeatingLockout Temperature

R (2) AI 11 AMB_AIR_ENTH n/a n/a n/a Outside Air Enthalpy

R / W (2) AV 10 AMB_AIR_HUM n/a n/a n/a Outside Air Humidity

R / W (5) BV 37 OAH_SENSOR n/a n/a n/a Outside Air Humidity Sensor Enabled

R / W (2) AV 7 AMB_TEMP n/a n/a n/a Outside Air Temperature

R (2) AI 9 OAQ_VALUE n/a 0 5000 Outside Demand Ventilation (OAQ)

Value (PPM)

R / W (5) BV 8 PWR_EX_INST n/a n/a n/a Power Exhaust Installed

R / W (5) BV 20 POP_ENABLED n/a n/a n/a Pre-Occupancy Purge Enabled

R / W (2) AV 81 POP_HOURS 4 0 23 Pre-Occupancy Purge Time (hours)

R / W (2) AV 82 POP_MINUTES 0 0 59 Pre-Occupancy Purge Time (minutes)

R (5) BI 17 PURGE_SWITCH n/a n/a n/a Purge Switch Status (0=open,1=closed)

R / W (5) BV 12 REDLINE n/a n/a n/a Redline (0=clear redline, 1=set redline

operation)

R (5) BI 4 REM_CONT_ENA n/a n/a n/a Remote Control Enabled

R / W (5) BV 111 REM_CONT_BAS_ECON n/a n/a n/a Remote Control Third Party BAS

Economizer Enable

R (2) AI 13 RET_AIR_ENTH n/a n/a n/a Return Air Enthalpy

R / W (2) AV 12 RET_AIR_HUM n/a n/a n/a Return Air Humidity

R (2) AI 5 RET_AIR_TEMP n/a n/a n/a Return Air Temperature

R / W (5) BV 38 RAH_SENSOR n/a n/a n/a Return/Inside Air Humidity Sensor

Enabled

R / W (2) AV 6 SPACE_TEMP n/a n/a n/a Space (Indoor) Air Temperature

R / W (2) AV 71 SPCE_ALM_TMP 0 0 25 Space Sensor Alarm Temperature

(degrees F, 0 = disabled)

R / W (2) AV 72 SPCE_ALM_TIM 0 0 120 Space Sensor Alarm Time (minutes F, 0

= disabled)

R / W (5) BV 26 SEN_FAULT_EN n/a n/a n/a Space Sensor Fault Override

(Construction Mode) Enabled

R / W (2) AV 73 SP_OFF_RANGE 3 0 5 Space TempratureSensorOffsetRange

(0-5 degrees)

R (2) AI 4 SUP_AIR_TEMP n/a n/a n/a Supply Air Temperature

R / W (2) AV 70 SAT_ALM_COOL 0 0 80 Supply Air Temperature Alarm Setpoint

for Cooling

R / W (2) AV 53 SAT_ALM_HEAT 0 0 120 Supply Air Temperature Alarm Setpoint

for Heating

R / W (5) BV 22 SAT_COOLING n/a n/a n/a Supply Air Temperature Limit for

Cooling Enabled

R / W (2) AV 3 SAT_COOL_SP 50 40 65 Supply Air Temperature Limit for

Cooling Setpoint (degrees F)

TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)

Read/

Write

BACnet

Object

Type

BACnet

Object

Inst Descriptor Default Min Max Point Description

Indice

Altri manuali Johnson Controls Portale

Johnson Controls

Johnson Controls MAP 1810 Manuale utente

Johnson Controls

Johnson Controls TL-MAP1810-OP Manuale utente

Johnson Controls

Johnson Controls YK-MAP1810-0E Manuale utente

Johnson Controls

Johnson Controls MAP 1810 Manuale utente

Johnson Controls

Johnson Controls MAP 1850 Manuale utente

Johnson Controls

Johnson Controls York Smart Equipment SC-EQUIP Manuale utente

Johnson Controls

Johnson Controls WNC1800 Manuale utente

Johnson Controls

Johnson Controls TL-MAP1810-OP Manuale utente

Johnson Controls

Johnson Controls WT-BAC-IP Manuale utente

Johnson Controls

Johnson Controls MAP Series Manuale utente

Johnson Controls

Johnson Controls 24-10737-8 Manuale utente

Johnson Controls

Johnson Controls WNC1800 Manuale utente

Johnson Controls

Johnson Controls VRF Smart Gateway Manuale utente

Johnson Controls

Johnson Controls WNC1800 Manuale utente

Johnson Controls

Johnson Controls E-Link Manuale utente

Johnson Controls

Johnson Controls MAP Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente