Johnson Controls Tyco Illustra Pro Gen4 Manuale utente

Table 2: Camera interior buttons / connections descriptions

Buttons / Connectors

Description

AC24V Power connector

PoE Ethernet port

Analog out port

Audio and Alarm pins

(See Figure 3 for descriptions)

Reset to factory default (Hold for 5

seconds and then release)

Power LED indicator

Reboots the camera

Security

Quick Start Guide

(8200-2007-01_E)

Illustra Pro Gen4 2MP & 8MP IR PTZ Outdoor camera

(P/N IPS02-P24-OI04 & IPS08-P25-OI04)

In the box

•1 x Illustra IR PTZ Camera

•1 x Printed Quick Start Guide

•1 x Printed Regulatory Document

•1 x NTSC/PAL output female BNC cable

•1 x 2-pin European style terminal block

•1 x Torx 20 security L-Key & 1 x Torx 10 security L-Key

•1 x 12-pin terminal connector for I/O function

•1 x Safety cable (Pre-attached to the camera)

•1 x Mount adaptor

•3 x ¼ 20 UNC security screws

•1 x Rubber grommet

•1 x RJ45 Insert tool

Installation tools

•1 x Screw driver

•1 x Torx 20 security L-Key & 1 x Torx 20 security L-Key

•1 x Drill

•1 x Wire cutters

Figure 1: PG4 IR PTZ camera parts

Figure 1

Table 1: Camera part descriptions

Number

Description

NPT Pendant Cap

Screw (x2) to open and lock the top cover

Top cover

SD Card Cover

Camera lens

Camera head

Quick reference

•Default IP: 192.168.1.168 (DHCP enabled)

•Default Username / Password: admin / admin

•Power: PoE 802.3bt 90w or AC 24V

Note: Before you power up the camera; please ensure that all

packaging has been removed, including packaging located inside

the bubble assembly. As part of the start-up sequence the camera runs

motor calibration, this includes a 15 second 'shake' procedure.

Accessing the camera interior buttons / connections

1. Use the Torx security L-Key to remove the two screws on the

camera top cover (1) (Figure 2).

Figure 2

Figure 3: Audio and alarm pin descriptions

Figure 3

Mounting the camera

Refer to the Illustra mounting accessories webpage

https://www.illustracameras.com/products/accessories/mounts for

assistance. The following mount accessory part numbers are

applicable with the Illustra Pro Gen4 2MP and 8MP IR PTZ camera:

RHOSW, RHOLW, RHOTR, ROTRF, RHOWCA, ROENDC.

Installing the rubber cable seal in to the NPT pendant cap

1. Securely place the rubber cable seal (2) (Figure 5) into the pendant

cap (3) (Figure 6).

Figure 6

2. Place the mount adaptor (1) (Figure 6) on to the NPT pendant cap

(3) (Figure 6) and align the holes on the mount adaptor with the

holes on the NPT pendant cap.

3. Insert the three security screws into the three holes and use the

Torx security L-Key to securely attach the screws and the mount

adaptor to the NPT cap.

Security

Mounting the camera to the RHOSW accessory

1. Hold the large loop on the safety lanyard (2) (Figure 4) up next to

the mounting arm (1) (Figure 4).

2. Ensure that the smaller loop on the safety lanyard is placed

around the mounting arm and then through the hole in the larger

loop so that the safety lanyard is securely attached to the

mounting arm.

3. Remove the safety lanyard screw (3) (Figure 4) on the camera.

4. Place the smaller loop on the safety lanyard around the screw

hole on the camera and then insert the screw to securely attach

the safety lanyard to the camera.

Mounting the camera to the RHOSW accessory (continued)

Figure 4

Inserting or removing the micro SD card

1. Remove the two screws located on the micro SD card cover (4)

(Figure 1).

Figure 5

Inserting or removing the micro SD card (continued)

2. Carefully pull open the cover to access the SD card slot (1)

(Figure 5) and insert (or remove) the micro SD card into (or from)

the camera.

Note: It is advised that you reboot the camera after inserting the

micro SD card.

3. Secure the two screws located on the micro SD card cover.

Note: The USB cable connection slot (2) (Figure 5) for Wi-Fi

configuration is also located under the micro SD card cover.

The Wi-Fi option allows wireless configuration of the camera at

the point of install in conjunction with the Illustra Tools app (Illustra

Wi-Fi dongle required).

Connecting the wires

This unit supports one of the following options as power supply:

1. Connect a power source.

•AC24V wired to connector and separate RJ45 Ethernet.

•PoE through RJ45 connector. The Outdoor unit operates with

IEEE 802.3bt (71W max).

2. Connect any optional audio or digital inputs or outputs.

Note: After connecting all cables ensure that the two screws on

the top cover are securely attached to maintain the waterproof

seal.

Installing the mount adaptor on to the NPT pendant cap

(continued)

Note: To maintain the waterproof seal only pierce holes that are

required for the installation.

Passing the RJ45 connector through the grommet

1. Remove the plug from the grommet (1) (Figure 7) by pulling the stub

(2) (Figure 7) to create a hole in the grommet.

Figure 7

2. Insert the RJ45 cable connector (1) (Figure 8) into the insert tool (2)

(Figure 8).

3. Push the insert tool and cable through the grommet hole (3) (Figure

8).

4. Remove the insert tool from the RJ45 connector and pass the cable

through the NPT cap (4) (Figure 8).

Security

Passing the RJ45 connector through the grommet

(continued)

Figure 8

Warnings

1. Before you power up the camera; please ensure that all

packaging has been removed, including packaging located

inside the bubble assembly.

2. Installation and service should be performed only by qualified and

experienced technicians and comply with all local codes and rules to

maintain your warranty.

3. Wipe the camera with a dry soft cloth. For tough stains, slightly apply

with diluted neutral detergent and wipe with a dry soft cloth.

4. Do not apply benzene or thinner to the camera, which may cause

the surface of the unit to be melted or lens to be fogged.

5. To meet EU EMC immunity requirements for security equipment the

mains power for equipment powering this unit should be backed up

by an uninterruptible power supply.

6. When the camera is powered up and not attached to a mount, or

unsupported mounts, or if the camera is loose in / on a mount then

this may result in motor calibration failure or camera vibration. Motor

calibration runs when the camera boots up.

7. Avoid operating or storing the unit in the following locations:

a. Near fluorescent lamps or objects with reflections.

b. Under unstable or flickering light sources.

TYCO and ILLUSTRA are trademarks and/or registered trademarks.

Unauthorized use is strictly prohibited.

Questo manuale è adatto per i seguenti modelli

Altri manuali Johnson Controls Telecamera di sicurezza

Johnson Controls

Johnson Controls Tyco Illustra Flex Manuale utente

Johnson Controls

Johnson Controls Tyco Illustra Manuale utente

Johnson Controls

Johnson Controls Illustra Flex Gen 4 Manuale utente

Johnson Controls

Johnson Controls TYCO Illustra Pro IPS02-P07-RT04 Manuale utente

Johnson Controls

Johnson Controls Tyco Illustra Essentials Gen4 Manuale utente

Johnson Controls

Johnson Controls Tyco Illustra Flex IFS03D1ICWTT Manuale di servizio

Johnson Controls

Johnson Controls tyco Illustra IBPN-M-IS-0 Manuale utente

Johnson Controls

Johnson Controls Illustra PRO Manuale utente

Johnson Controls

Johnson Controls Tyco Holis JSV Manuale utente

Johnson Controls

Johnson Controls tyco Illustra Pro Manuale utente

Johnson Controls

Johnson Controls Illustra Standard Gen 3 Manuale utente

Johnson Controls

Johnson Controls Holis JSV02-D02-OI01 Manuale utente

Johnson Controls

Johnson Controls Tyco Pro Gen2 Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente