Johnson Controls FS-1300 Manuale utente

Damper and Actuator Product Guide 268.1

Fire/Smoke Section

Installation Bulletin FS-1300

Issue Date 0499

Part No. 44-352-29, Rev. — www.johnsoncontrols.com

Code No. LIT-2681195

DANGER: To avoid causing death or

serious bodily harm to building

occupants, follow all instructions

carefully. Dampers must close

completely to preserve the

integrity of the fire barrier.

tems Needed

•screwdriver, flat-blade

•nut driver, 1/2 inch socket

•open-end wrench, adjustable to 1 inch

eneral

Note: For further information, refer to

UL File No. R11172 and

CSFM3230-0554:128.

The FS-1300 Combination Fire/Smoke Leakage-rated

Life Safety Damper is designed to restrict the passage

of flame or smoke when in the closed position, under

dynamic or static conditions.

After installation, when power (electric or pneumatic) is

applied to the actuator, the damper blades will be

driven to the open position by the actuator.

When the primary temperature sensor detects heat, it

breaks power to the actuator, closing the damper

blades through the spring-return mechanism of the

actuator. The damper is now in the smoke protection

mode (damper closed via actuator).

If the air temperature reaches the fusible link

temperature (secondary temperature sensor), the link

separates. The damper linkage disengages from the

actuator, allowing the blades to close by a torsion

spring. The damper is now in fire protection mode

(damper closed via torsion spring).

FS-1300 Combination Fire/Smoke Dampers are

approved for mounting in fire walls constructed of

masonry or gypsum wallboard (metal or wood studs)

and in cement floors or ceilings.

Figure 1: Wall Mounting

Figure 2: Floor/Ceiling Mounting

Table 1: Damper Size Limits

Size Limits Width, in. Height, in.

Minimum 15 14

Maximum Single Panel 32 48

Damper Maximum

(Wall Installation) 64 96

Damper Maximum

(Floor Installation) 64 72

Note: FS-1300 size limits are a function of past UL tests.

Actual damper size is 1/4 inch less than nominal.

FS-1300 Combination Fire/Smoke Damper Installation

1-1/2 Hour/Class II Leakage

2 FS-1300 Combination Fire/Smoke Damper Installation Bulletin

FS-1300 dampers include an 18-gauge galvanized

steel sleeve, 24-inch-long, which is used for a 6 inch or

less fire barrier standard. Any barrier larger than

6 inches requires an optional 32-inch-long sleeve

length.

All dampers include an identification label providing the

following information:

•damper model and size

•manufacturing date code (year/week)

•top of damper

•air leaving side

An additional UL identification label provides the

following information:

•type, and hourly rating

•designation for use in dynamic systems

•maximum tested airflow and pressure difference

•electrical and/or pneumatic ratings

•degradation test temperature

•intended mounting position

imensions

Airflow

3.5 4.5, 8.5,

or 12.5

Width

Height

Figure 3: Mounting Dimensions with

Electric Actuator, inches

Airflow

3.5 4.5, 8.5,

or 12.5

Width

Height

Figure 4: Mounting Dimensions with

Pneumatic Actuator, inches

Figures 3 and 4 show the typical mounting dimensions

for the FS-1300.

Note: The side angle by the actuator is factory

mounted for location of the damper within the

fire barrier. Do not remove this angle during

installation.

omponent Identification

Sleeve

Fusible Link

and Spring

Actuator

Primary

Temperature

Sensor Box

Airflow

Factory-

installed

Angle

Jackshaft

Linkage

Figure 5: FS-1300 Components

Figure 5 identifies the major components of the

FS-1300.

FS-1300 Combination Fire/Smoke Damper Installation Bulletin 3

tud Framing

Gypsum panels must be screwed on maximum

12-inch centers to all stud and runner flanges

surrounding the opening.

Ceiling Runner

Floor Runner

12 in.

Screws

Double stud

not required

on penetrations

36 x 36 inches

or less.

Figure 6: Framing

Sleeve

Mounting Angle

2-1/2 inch Minimum

Stud or Runner

1/2 inch Minimum

Gypsum Wallboard

Minimum

1 inch

Figure 7: Three-Hour Wall Rating

Fire Barrier

Sleeve

Damper Width

Damper Height

0.5 inch

Minimum

Damper

Fire Barrier

Figure 8: Fire Barrier Opening Requirements

The opening in the fire barrier should be 1/8 inch per

foot, or 1/2 inch larger than the width and height

dimensions of the sleeve, to accommodate the heads

of the fasteners securing the sleeve to the damper.

Refer to Figure 8.

nstallation

1. Check the schedules (furnished by others) for

correct damper location within the building.

2. The FS-1300 Combination Fire/Smoke Life Safety

Damper must be installed in accordance with

Standard NFPA-90A, at the point where a duct

passes through a required fire barrier. The blades,

when closed, shall be within the plane of the fire

barrier (wall or floor).

IMPORTANT Horizontal airflow only. The

damper must be installed in the

wall with the fusible link above

the centerline of the damper. See

labels on damper.

3. Verify that the fusible link is secure and was not

damaged or lost during shipment. If the fusible link

is missing, obtain a new link and follow installation

instructions provided with the link.

Mounting

Angles

Top

3 in. maximum

Side

Sleeve

Damper

Fire Barrier

6 in.

maximum

6 in.

3 in.

maximum

Figure 9: Installing and Fastening Mounting Angles

4. Mounting angles are required by building codes for

restricting the passage of flame through any gaps

created by the passage of the sleeve through the

fire barrier, and are provided with the FS-1300

Combination Fire/Smoke Leakage-rated Damper.

The mounting angles are precut to be installed so

that two sides extend past the other side (Figure 9

shows one corner), allowing no gaps to exist.

Attach the angles provided with the damper to the

sleeve, using the No. 10 self-tapping screws

provided.

5. Install the damper through the hole in the fire

barrier until mounting angles contact the fire

barrier.

4 FS-1300 Combination Fire/Smoke Damper Installation Bulletin

DANGER: To avoid causing death or serious

bodily harm to building occupants,

allow for expansion of duct. Do not

fasten or weld the angles together

at the corners of the sleeve. Do

not secure the mounting angles to

the fire barrier.

6. While supporting the damper, install the mounting

angles to the sleeve on the other side of the fire

barrier, using the No. 10 self-tapping screws

provided.

Note: All sizes will have enough screws to be spaced

at 6-inch centers, starting within 3 inches from

the corners.

Mounting Angle

Screw or

Weld

Sleeve

Fire

Barrier Minimum

1 inch

Damper

Figure 10: Fire Barrier and Mounting Angle Overlap

7. After installation, verify that the mounting angles

overlap the fire barrier by a minimum of 1 inch.

8. For proper damper operation, the frame must be

mounted square to prevent blade binding.

9. Visually inspect the damper to verify that the

fusible link is installed and was not damaged

during shipping.

Plain "S" Slip Double "S" Slip

Figure 11: Sleeve Connectors

10. Connecting ducts shall not be continuous and shall

terminate at the sleeve. The duct-to-damper sleeve

connection shall be of a breakaway style, such as

“S” or double “S” connectors. Use the plain “S” slip

when the duct or sleeve size is slightly different. Use

the double “S” slip when the sizes are equal.

11. The ducts connecting to the sleeves shall be equal

or less than the sleeve thickness. All FS-1300

sleeves are 18-gauge galvanized steel.

onnections

Actuators are mounted with linkage to drive the

jackshaft.

Electric Actuator

CAUTION: Shock Hazard.

Disconnect the electrical power

supply before wiring the switches,

sensor, and motor actuator to

avoid possible electrical shock or

damage to the equipment.

Figure 12: Actuator Terminal Location

L1 or H

L2 or G

Thermostat or

Switch

Actuator

Auxiliary Switch

Com

Low-Input

Holding High-Input

Running

N.C.

N.O.

N.C.

N.O.

Figure 13: Actuator Wiring Diagram

Make all wiring connections in actuator using copper

conductors and approved solderless connectors. Wire

in accordance with NEC and local regulations.

1. Remove the four screws securing the cover to the

actuator. Remove the cover.

2. Remove the knock-out from the side of the

actuator.

3. Attach the conduit connector though the hole and

install the wires to the actuator.

4. Connect the ground wire to the case ground

terminal, shown in Figure 12.

FS-1300 Combination Fire/Smoke Damper Installation Bulletin 5

5. Wire the actuator as shown in Figure 13. Use

approved high-temperature connections.

To verify operation:

1. Verify voltage of actuator and power available

before applying power to the actuator.

2. After power is applied to the actuator, verify that

the damper blades are fully open.

3. Remove power and verify that the damper blades

fully close.

4. Apply power and allow the damper blades to

remain in the open position.

5. Replace and secure the cover to the actuator.

Pneumatic Actuator

1. Make sure that all linkage fasteners are secure

before making air line connections.

Copper

Tubing

Sleeve

Jackshaft

Universal Mounting Bracket

Figure 14: Pneumatic Connections

2. Copper tubing must be used and looped to allow

pivoting of the actuator.

CAUTION: Shock Hazard.

Disconnect the electrical power

supply before wiring the

switches and sensor to avoid

possible electrical shock or

damage to the equipment.

3. Make all wiring connections in handy box using

copper conductors and approved solderless

connectors. Wire in accordance with NEC and

local regulations.

To verify operation:

1. When the air supply is applied to the actuator,

verify that the damper blades are fully open.

2. Remove the air supply and verify that the damper

blades fully close.

3. Connect the air supply and allow the damper

blades to remain in the open position.

Table 2: Replacement Parts

Replacement

Code Number Description

DS-3153-600 Pneumatic Actuator, Body Only

DMPR-RS005 DMPR-S60024 - 60 lb·in, 24 VAC

Actuator

DMPR-RS006 DMPR-S60024S - 60 lb·in, 24 VAC

Actuator w/auxiliary switch

DMPR-RS007 DMPR-S60120 - 60 lb·in, 120 VAC

Actuator

DMPR-RS008 DMPR-S60120S - 60 lb·in, 120 VAC

Actuator w/auxiliary switch

DMPR-RS301 165°F temperature sensor

DMPR-RS302 212°F temperature sensor

DMPR-RS303 250°F fusible link

DMPR-RS304 350°F fusible link

6 FS-1300 Combination Fire/Smoke Damper Installation Bulletin

Table 3: FS-1300 Dynamic Rating - Electric Actuator

Width x Height, in. Mounting Ordering

Code Maximum

Flow,

fpm*

Maximum SP,

in. WG** Actuator, Tested as

Matched Set with

Damper (350°F)

Minimum: 15 x 14 Wall or Ceiling TOVLE, DMPR-S60120,

Maximum: 32 x 48 Wall TOVHE 2500 4 DMPR-S60120S,

Maximum: 32 x 36 Ceiling DMPR-S60024,

DMPR-S60024S

* Maximum Flow is the velocity against which the actuator listed in Table 3 will be able to operate the damper to the fully

closed position and provide the rated leakage in the marked direction of airflow.

** Maximum SP is the static pressure against which the actuator listed in Table 3 will be able to operate the damper from

the fully closed position in the marked direction of airflow.

Table 4: FS-1300 Dynamic Rating - Pneumatic Actuator

Width x Height, in. Mounting Ordering

Code Maximum

Flow, fpm* Maximum SP,

in. WG** Actuator, Tested

as Matched Set

with Damper

(350°F)

Minimum: 15 x 14 Wall or Ceiling TOVLP,

Maximum: 32 x 48 Wall TOVHP 2800 8 DS-3153-2

Maximum: 32 x 36 Ceiling

Note: Table 4 information is based on a 20 psi minimum supply pressure for pneumatic actuators.

* Maximum Flow is the velocity against which the actuator listed in Table 4 will be able to operate the damper to the fully

closed position and provide the rated leakage in the marked direction of airflow.

** Maximum SP is the static pressure against which the actuator listed in Table 4 will be able to operate the damper from

the fully closed position in the marked direction of airflow.

Table 5: FS-1300 Dynamic Rating - Fire Mode

Width x Height, in. Mounting Ordering Code Maximum

Flow,

fpm*

Maximum SP,

in. WG** Actuator

Minimum: 15 x 14 Wall or Ceiling TOVLE, TOVHE,

Maximum: 32 x 48 Wall TOVLP, TOVHP 3500 8 Jackshaft Spring

Maximum: 32 x 36 Ceiling

Note: The ratings in Table 5 are valid in either direction of airflow.

FS-1300 Combination Fire/Smoke Damper Installation Bulletin 7

Table 6: UL Leakage-Rated Classifications

Class Static Pressure (SP), inches water

14812

I4 8 11 14

II 10 20 28 35

Leakage in cfm/sq ft

All technical information is compiled from test data, corrected to standard temperature and pressure conditions,

determined using instrumentation and procedures in accordance with AMCA Standard for Test Methods for

Louvers, Dampers, and Shutters No. 500-89.

For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable

for damages resulting from misapplication or misuse of its products.

At Johnson Controls, delivering environmentally sound products and services is part of our corporate-wide

commitment to continuous improvement. We do this by reducing raw material consumption, recycling, eliminating

the use of toxins, and conserving and preserving natural resources. We believe that what is good for the

environment and the safety and health of all people is good for Johnson Controls. And we never forget that clean

water, air, and land is everyone’s business.

8 FS-1300 Combination Fire/Smoke Damper Installation Bulletin

Notes

Controls Group www.johnsoncontrols.com

507 E. Michigan Street FAN 268.1

P.O. Box 423 Damper and Actuator Product Guide

Milwaukee, WI 53201 Printed in U.S.A.

Altri manuali Johnson Controls Sensore di sicurezza

Johnson Controls

Johnson Controls tyco Bentel Security BW-IRC Manuale utente

Johnson Controls

Johnson Controls PG9350SL Manuale utente

Johnson Controls

Johnson Controls PG8932 Manuale utente

Johnson Controls

Johnson Controls Tyco Visionic MP-843/XHM2 Manuale utente

Johnson Controls

Johnson Controls LC-203 Manuale utente

Johnson Controls

Johnson Controls PG9350SL Manuale utente

Johnson Controls

Johnson Controls FTX-P2J Manuale utente

Johnson Controls

Johnson Controls LC-200S Manuale utente

Johnson Controls

Johnson Controls LC-200 Manuale utente

Johnson Controls

Johnson Controls tyco Bentel Security BW-DTM Manuale utente

Johnson Controls

Johnson Controls PGP914 Manuale utente

Johnson Controls

Johnson Controls DSDN Manuale utente

Johnson Controls

Johnson Controls MP-802 PG+ Manuale utente

Johnson Controls

Johnson Controls PG9200AX Manuale utente

Johnson Controls

Johnson Controls F62AA Manuale utente

Johnson Controls

Johnson Controls tyco Bentel Security BW-SHK Manuale utente

Johnson Controls

Johnson Controls PG9200AX Manuale utente

Johnson Controls

Johnson Controls NEXT CAM PG+ Foglio di istruzioni

Johnson Controls

Johnson Controls Tyco Kantech T.REX Istruzioni per il montaggio

Johnson Controls

Johnson Controls LC-203 Manuale utente

Johnson Controls

Johnson Controls Tyco SR Series Manuale utente

Johnson Controls

Johnson Controls RLD-H10G Manuale utente

Johnson Controls

Johnson Controls PGP922 Manuale utente

Johnson Controls

Johnson Controls HTD-432 PG2 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente