JPRiDE JPT2 Manuale utente
User manual
JPRiDE-JPT2
Contents
1.Productoverview--------------------------------------------------------------1
2.Essentialoperationandfunction-----------------------------------------------2
3.TXtransmitterusage----------------------------------------------------------3
4.RXreceiverusage--------------------------------------------------------------6
5.Charging------------------------------------------------------------------------9
6.IndicatorLEDlight-------------------------------------------------------------10
7.Productdescription----------------------－---------------------------------11
8.NotesandFAQ--------------------------------------------------------------12
1.Product overview
Packinglist：
A. JPT2bluetoothadapter1
B. 3.5mmaudiocable1
C. MicroUSBchargingcable1
D. Manual1
E．SPDIFcable1
2.Essentialoperationsandfunctions
button function operation
MFB
Power on
(TX/RX)
In power off status, press MFB around 2 seconds, blue
LED flashes twice, JPT2 is powered on. If JPT2 didn’t
connect with any device before, it will enter into pairing
mode automatically after power on, with Blue and Red
LED flashes alternately
Power off
(TX/RX)
In power on state, press MFB around 2 seconds, Red
LED flashes twice (if release MFB immediately when
Red LED lighten, Red LED may only flashes once),
JPT2 power off; Please re-power on the unit after power
off the unit 3 seconds later since the voltage of the
chipset may not disappear totally
Play/PauseRX In music playing, short press MFB to play/pause
music
Paringbutton
(TX/RX)
In standby status or connected status, short press“Paring button”（last for
0.2 second）enter into pairing mode, Blue and Red LED flashes
alternately; In connected standby status, press“Paring button” 3 seconds
quit connected status, enter into paring mode again
Volumeup/nextsong
（RX）
long press “Volume up” button to switch next song, short press“Volume
up”button” to increase volume
volumedown/
previoussong
Long press “Volume down” button to switch previous song, Short press
“Volume down” button” to decrease volume
ModeSPDIF/AUX
Power on default setting SPDIF mode，when insert Φ3.5mm audio cable,
automatic switch to AUX mode ；when pull out Φ3.5mm audio cable
switch to SPDIF mode
In SPDIF mode, TX status put the optical fiber into SPDIF TX port, RX
status put the optical fiber into SPDIF RX port
StatusTX/RX
Switch between RX receiver/TX transmitter status
Once switch the status, the pairing information for the former mode will be
cleared up
Please don’t switch TX/RX mode within 3 seconds after powered off
3.TXtransmitterusage
3.1InTXstatusbluetoothpairandconnect
A．Power off status pull TX/RX button to TX side，long press MFB 2 seconds to power
on，after blue LED flashes twice, JPT2 power on, when paring list is clear (JPT2 didn’t
connected with any devices before), power on then enter into pairing mode automatically,
Blue and Red LED flashes alternately
B．Power on the unit and standby status, short press “Paring button”（last for 0.2
second）enter into pairing mode, Blue and Red LED flashes alternately
C．Put your devices（bluetooth headset、speaker or receiver）power on and enter into
paring mode，usually LED flash style is blue and red LED flashes alternately or blue
LED flashes quickly
D．Put JPT2with your device together and wait for 5-30 seconds，after connect
successfully，blue LED flashes once then disappear
E．When you want to use in AUX mode, just insert the Φ3.5mm audio cable then SPDIF
mode automatically switch to AUX mode；when you want to use in SPDIF mode, pull the
Φ3.5mm audio cable out then automatically switch to SPDIF mode
3.2 In TX status connect with two bluetooth devices simultaneously
A．Paired with the first device successfully, then short press the paring button，enter
new paring mode，red and blue LED flash alternately.
B．Make the second device（bluetooth headset, speaker or receiver）to power on and
enter into paring mode.
C．Put JPT2 together with the second device, wait for 5-30 seconds, after paired
successfully, blue LED blink once then disappeared, that means JPT2 has connected
with two bluetooth devices simultaneously
Notes：
*If JPT2 can’t connect two devices, please power off then power on again
* When JPT2 is working as Bluetooth transmitter try to connect with two device
simultaneously, perhaps can’t compatible with all bluetooth devices in the market，some
devices has no sound, discontinuous playing or can’t connect
3.3InTXstatusconnectwithTV
Connect JPT2 with your TV by 3.5mm audio cable or optical fiber, then It can hear the
sound coming from TV in the device which connect with JPT2
Notes：
*If use fiber optic cable, please insert it into SPDIF TX port of JPT2
*If no sound in the Bluetooth device，please use a wired headset insert to the Φ3.5mm
audio port of TV，check if there is sound coming from the TV
*If you couldn’t here sound of TV by the bluetooth device, please check the audio setting
by remote control, usually TV can set optical fiber, Φ3.5mm audio, one of the speakers in
the TV make sounds, also can set them make sounds simultaneously
4.RXtransmitterusage
4.1InRXstatusbluetoothpairandconnect
A．In power off status pull TX/RX button to RX side，then long press MFB 2 seconds,
after blue LED flashes twice, JPT2 power on, when paring list is clear (JPT2 didn’t
connect any devices before), power on and automatically enter into pairing mode
B．Power on the unit in standby status, short press“Paring button”（last for 0.2 second）
enter pairing mode, Blue and Red LED flashes alternately; in connected standby status,
long press“paring button” 3 seconds can force out connected status, enter into new
paring mode
C．Put JPT2 with your smart phone (laptop , tablet) together, open the smart phone’s
bluetooth function, and click search, click connect when JPT2 appeared
D．After connect successfully, blue indicator LED long lit, connect headset or speaker
with JPT2 by audio cable or optical fiber, and play music in your smart phone (after
playing music the blue indicator LED disappeared) then can listen to music came from
smart phone
E．When you want to use in AUX mode, just insert the Φ3.5mm audio cable then SPDIF
mode automatically switch to AUX mode; when you want to use in SPDIF mode，pull the
Φ3.5mm audio cable out then automatic switch to SPDIF mode
4.2InRX status connect with two bluetooth devices simultaneously
A．Paired with the first device successfully, then short press the paring button，enter
new paring mode，red and blue LED flash alternately.
B．Make the second device（computer, tablet or cellphone) power on and turn on
bluetooth function
C．Put JPT2 together with the second device, click the second device’s bluetooth search,
click connect when JPT2 appeared. After paired successfully, blue LED blink once then
disappeared, that means JPT2 has connected with two bluetooth devices simultaneously
Note:
*JPT2 connected two bluetooth devices simultaneously, it only can play one cellphone’s
music, when you want to play another cellphone’s music, you need to pause or close the
former cellphone’s music
4.3InRXstatusconnectwithspeaker
Connect JPT2 with your home speaker by Φ3.5mm audio cable or optical fiber, then play
music in the cellphone (tablet, computer ) which has already connected with JPT2 by
bluetooth, you can listen to music from the speaker
Notes：
*If use optical fiber, please insert it into SPDIF RX port of JPT2
*If there is no sound from the speaker, please insert the audio cable into the cellphone’s
audio interface to play music, check if there is any problem with the speaker
Indice
