Jumper JPD-700A Manuale utente
Bluetooth Weight Scale
JPD-700A
User Manual
Shenzhen Jumper Medical Equipment Co., Ltd.
Date of compilation: April 2017 Version: A/0
●Please read this User Manual carefully before using the product.
Foreword
Thank you for purchasing the Jumper Bluetooth Weight Scale
JPD-700A.
This product is intended to be used to measure body weight. It can be
connected to a smart phone via Bluetooth, and the measured data will
be transmitted to the phone synchronously. This means that users can
check their weight anytime by opening the APP for weight
management on their phone. This product helps users to develop good
habits for diet management and exercise for the purposes of managing
their weight.
Jumper reserves the copyright for this User Manual and no extraction
or copying of the content herein is permitted without approval.
Contents
FCC Statement...................................................................1
Quick Use...........................................................................2
Product Structural Components and Display…….………3
Unit Conversion.................................................................4
Instructions for Use.......................................................5-11
FAQs on Weight Measurement.........................................12
Troubleshooting................................................................13
Safety Caution…….….....................................................14
Description of Marks and Symbols..................................15
Cleaning and Maintenance...............................................16
Technical Specifications.............................................17-18
FCC Statement
- 1 -
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Notes:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
Quick Use
- 2 -
Using the scale alone
1. Place the scale on a hard and flat surface. Gently step on it and wait
until it turns on when the LED displays digits. Then step off the scale
and stand back on in an upright and steady position when the LED
displays zero. See the picture below for the correct standing position.
2. The weight value on the display will flash three times. Do not read
it until it stabilizes.
Product Structural Components and Display
- 3 -
1. Product Structural Components
2. Display Interface
Digital display
Bluetooth
斤 lb kg
Weight units
LED Display
Sensor
Measuring Surface
Battery Cover
Unit Conversion
- 4 -
Converting Weight Units
The factory default unit is kg. For unit conversion, open the battery
cover at the back with the power off and adjust the gear toggle
switch. The units available are kg, lb and jin (500g) from left to right.
When the switch is placed at one of the gears, the displayed unit
automatically switches to the corresponding weight unit after the
scale is turned on.
※ The unit conversion toggle switch is located inside the battery case
at the back of the scale.
Instructions for Use
- 5 -
Pairing the Scale with the Mobile APP
1. Take out the insulation film
Open the battery cover at the back and pull out the insulation film.
Close the cover and place the product on a hard and flat surface.
※ When replacing the batteries, please install three AAA batteries
based on the position of positive and negative poles (alkaline AAA
batteries are preferred)
2. Download the APP client
Scan the QR code to download and install the mobile client software:
Android and ios users can scan the QR code on the product package or
this page to download “JUMPER Health” and install it as instructed.
Instructions for Use
- 6 -
3. User registration and login
Open “JUMPER Health”, complete the user registration, and login as
instructed. Enter your nickname, gender, date of birth and height as
instructed.
Instructions for Use
- 7 -
4. Enter the Monitoring Page
After the registration and login, click “Detection” at the bottom of the
page, and then choose “Weight” to enter the weight monitoring
module.
Indice
