Jung BM360MBWW Manuale utente
Motion detector mini basic
Motion detector mini basic
Art. no.: BM360MBWW
Motion detector mini basic
Art. no.: BM360MBWW-270
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. During installation and cable routing, comply with the regulations and
standards which apply for SELV circuits.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end customer.
2 Intended use
Intended use
– Brightness-independent detection of motion indoors.
– Connection to the KNX devices mentioned under accessories e.g. Multistation or push
button interface for the automatic switching of loads.
– Power supply via the unchoked output of a KNX power supply or power supply unit with
safety extra-low voltage (SELV).
– Clamp mounting in suspended ceilings.
– Ceiling mounting on fixed ceilings in appliance box according to DIN 49073 or surface-
mounted housing (see accessories)
3 Function
– Brightness-independent detection of motions in the detection field
– Switch on: After detecting motion
– Switch off: No motion in the detection field and run-on-time elapsed
– Potential-free electronic switching contact
4 Information for electrically skilled persons
4.1 Fitting and electrical connection
Selecting installation location
The motion detector is installed on the ceiling and monitors the surface under it.
￭ Select a vibration-free installation location. Vibrations can lead to unwanted switching.
￭ Avoid interference sources in the detection area. Interference sources, e.g. heaters, vent-
ilation, air conditioners, and cooling light bulbs can lead to unwanted detections.
If necessary, the detection field can be limited using the push-on cover in order to minim-
ize the influence of interference sources.
1 / 7
82403113 17.11.2021
J0082403113
Motion detector mini basic
Motion detection
Figure1: Tangential and radial direction of motion
The device has a detection field of 360°. The diameter of the detection field depends on the in-
stallation height and the direction of motion of persons in the detection field (Figure 1). The de-
tection field becomes larger the greater the installation height, while the detection density and
sensitivity are reduced at the same time. The following applies to an installation height of 3 m:
1: Range for tangential motion on the ground Ø approx. 6 m
2: Range for radial motion on the ground Ø approx. 5.5 m
DANGER!
Electrical shock on contact with live parts in the installation environment.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live parts
in the working environment.
Create a mounting opening in the suspended ceiling
Figure2: Mounting in the suspended ceiling
(1) Spring clamp
(2) Cable fixation
2 / 7
82403113 17.11.2021
J0082403113
Motion detector mini basic
(3) Terminal
(4) Motion detector
(5) Design ring
The environment in the suspended ceiling must be dry.
Max. thickness of the suspended ceiling approx. 25 mm. Installation depth min. 35 mm. Dis-
tance between concrete ceiling and suspended ceiling min. 20 mm (Figure 2).
￭ Create ceiling cut-out Ø 44...45 mm(Figure 2).
Connecting the device
Figure3: Clampable conductor cross-section
Recommended line J-Y(St)Y 2×2×0.8 (2 wire pairs, conductor diameter 0.8 mm this corres-
ponds to a conductor cross-section of 0.5 mm²).
For the cable length, also observe the information in the instructions for the device to be con-
nected.
￭ Use the unchoked output of a KNX power supply or power supply unit with safety extra-
low voltage as power supply.
￭ Connect the connection cable to device connection terminal (3) (Figure 2).
Connection in general
Terminal assignment of motion detector
Terminal Connection
DC24V + Power supply +
DC24V – Power supply GND
A
A'
Switching output
Figure4: Connection in general
For connection diagrams for various KNX devices, see accessories
Figure5: Connection to Multi station, Rotary sensor
3 / 7
82403113 17.11.2021
J0082403113
Motion detector mini basic
Figure6: Connection to Binary input 6-gang
Figure7: Connection to Binary input 8-gang, 24 V
Figure8: Connection to Push-button interface, 2-gang, Push-button interface, 4-gang
Figure9: Connection to flush-mounted actuators: Switch actuator, 2-gang / blinds actuator, 1-
gang, Switch actuator, 1-gang, Universal dimming actuator, 1-gang
Figure10: Connection to Room temperature controller with push-button interface 4-gang, Room
autostat with push-button interface 4-gang, CO2 multi-sensor
4 / 7
82403113 17.11.2021
J0082403113
Motion detector mini basic
Figure11: Connection to Valve drive (motor-operated) with controller
Figure12: Connection to KNX Push-button universal
(Figure 4) (6) Motion detector mini basic
(Figure 5) (7) Multi station, Art. no.: 23066REGHE, Rotary sensor, Art. NoD-
S4092TS.:
(Figure 6) (8) Binary input 6-gang, Art. no.: 2116REG
(Figure 7) (9) Binary input 8-gang, 24 V, Art. no.: 2128REG
(Figure 8) (10) Push-button interface, 2-gang, Art. no.: 2076-2T, Push-button
interface, 4-gang, Art. No2076-4T.:
(Figure 9) (11) Switch actuator, 2-gang / blinds actuator, 1-gang, Art. no.:
230021SU, Switch actuator, 1-gang, Art. no.: 230011SU, Univer-
sal dimming actuator, 1-gang, Art.no.: 390011SU
(Figure 10) (12) Room temperature controller with push-button interface 4-
gang, Art. no.: ..2178TS, Room autostat with push-button interface
4-gang, Art. no.: ..2178 ORTS.., CO2 multi-sensor, Art.no.:
CO2..2178..
(Figure 11) (13) Valve drive (motor-operated) with controller, Art. no.:
2177SVR
(Figure 12) (14) KNX Push-button universal, Art. no.: ..109.1ST
Mounting the device in the suspended ceiling
￭ Secure the connection cable with the enclosed cable fixation (2) (Figure 2).
￭ Bend back the spring clamps (1) and push the motion detector (4) into the suspended
ceiling (Figure 2).
￭ Attach the large design ring (5) and rotate it in clockwise direction (Figure 2).
5 Technical data
Rated voltage DC 24 ... 32 V SELV
Standby power max. 0.1 W
Current consumption max. 4 mA
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Relative humidity 10 ... 100 % (no moisture condensation)
Protectionclass III
5 / 7
82403113 17.11.2021
J0082403113
Motion detector mini basic
Degree of protection IP44
Detection angle 360°
Installation height 3 m
Detection field Ø approx. 6 m
Run-on time
BM360MBWW approx. 10 s
BM360MBWW-270 approx. 270 s
Switching output
Electric strength 40 V
Current carrying capacity max. 50 mA
Connected load max. 150 mW
Dimensions
Dimensions Ø×H 53.5 × 38 mm (with design ring)
Ceiling cut-out Ø×D 44 × 35 mm
Cable length max. 30 m
6 Accessories
Power supply 160 mA Art.-no.: 20160REG
Power supply 320 mA Art.-no.: 20320REG
Power supply 640 mA Art.-no.: 20640REG
Power supply 1280 mA Art.-no.: 21280REG
Multi station Art.-no.: 23066REGHE
Binary input 6-gang Art.-no.: 2116REG
Binary input 8-gang, 24 V Art.-no.: 2128REG
Push-button interface, 2/4-gang Art.-no.: 2076-..T
Switch actuator, 1-gang Art.-no.: 230011SU
Universal dimming actuator, 1-gang Art.-no.: 390011SU
Switch actuator, 2-gang / blinds actuator, 1-
gang
Art.-no.: 230021SU
Room temperature controller with push-button
interface 4-gang
Art.-no.: ..2178TS
Room autostat with push-button interface 4-
gang
Art.-no.: ..2178 ORTS..
CO2 multi-sensor Art.-no.: CO2..2178..
Rotary sensor Art.-no.: DS4092TS
KNX Push-button universal Art.-no.: ..109.1ST
Valve drive (motor-operated) with controller Art.-no.: 2177SVR
Flush mounting set Art.-no.: PMM-UP-SET-WW
Surface mounting set Art.-no.: PMM-AP-SET-WW
7 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
6 / 7
82403113 17.11.2021
J0082403113
Motion detector mini basic
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
www.jung.de
7 / 7
82403113 17.11.2021
J0082403113
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Jung Sensore di sicurezza
Jung
Jung 3360 Manuale utente
Jung
Jung BM 240 S1A WW Manuale utente
Jung
Jung 3361MWW Manuale utente
Jung
Jung Observer 110 Manuale utente
Jung
Jung 3361WW-01 Manuale utente
Jung
Jung Observer 220 Manuale utente
Jung
Jung BT17361 Series Manuale utente
Jung
Jung 17180 Series Manuale utente
Jung
Jung HOME BT 17181 Series Manuale utente
Jung
Jung Observer 70 Manuale utente
Jung
Jung DWPM17360AL Manuale utente
Jung
Jung DWPMK360WW Manuale utente
Jung
Jung FMDW360WW Manuale utente
Jung
Jung KNX 3361MWW-01 Manuale utente
Jung
Jung BT 17182 Series Manuale utente
Jung
Jung Mini basic Manuale utente
Jung
Jung PMK 360 WW Manuale utente
Jung
Jung FM ES 36804 REG Manuale utente
Jung
Jung PMU 360 WW Manuale utente
Jung
Jung 2103 REG ES Manuale utente
