Juniper SRX5600 Manuale utente

Removing Components from the SRX5600 Chassis Before Installing It Without a

Lift

If you cannot use a mechanical lift to install the services gateway (the preferred

method), you can install it manually. Before installing the services gateway manually,

you must first remove components from the chassis, and reinstall the components

the chassis is installed in the rack. With components removed, the chassis weighs

approximately 65 lb (29 kg).

1. Removing the Power Supplies Before Installing the SRX5600 Services Gateway

Without a Lift on page 1

2. Removing the Fan Tray Before Installing an SRX5600 Services Gateway Without

a Lift on page 2

3. Removing SCBs Before Installing an SRX5600 Services Gateway Without a

Lift on page 3

4. Removing IOCs, Flex IOCs, and SPCs Before Installing an SRX5600 Services

Gateway Without a Lift on page 4

Removing the Power Supplies Before Installing the SRX5600 Services Gateway Without

a Lift

Remove the leftmost power supply first and then work your way to the right. To

remove the AC or DC power supplies for each power supply (see Figure 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to one of the ESD points on the chassis.

2. On an AC-powered services gateway, switch the AC input switch on each power

supply to the off (O) position. On a DC-powered services gateway, Move the DC

circuit breaker on each DC power supply to the off (O) position.

We recommend this even though the power supplies are not connected to power

sources.

3. Loosen the captive screws on the bottom edge of the power supply faceplate.

4. Pull the power supply straight out of the chassis.

Removing Components from the SRX5600 Chassis Before Installing It Without a Lift ■1

Figure 1: Removing a Power Supply Before Installing the Router

Removing the Fan Tray Before Installing an SRX5600 Services Gateway Without a Lift

To remove the fan tray (see Figure 2 ):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to one of the ESD points on the chassis.

2. Loosen the captive screws on the fan tray faceplate.

3. Grasp the fan tray handle and pull it out approximately 1 to 3 inches.

4. Press the latch located on the inside of the fan tray to release it from the chassis.

5. Place one hand under the fan tray to support it and pull the fan tray completely

out of the chassis.

2■Removing the Fan Tray Before Installing an SRX5600 Services Gateway Without a Lift

Figure 2: Removing the Fan Tray

Removing SCBs Before Installing an SRX5600 Services Gateway Without a Lift

To remove the SCBs (see Figure 3):

1. Place an electrostatic bag or antistatic mat on a flat, stable surface.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to one of the ESD points on the chassis.

3. Rotate the ejector handles simultaneously counterclockwise to unseat the SCB.

4. Grasp the ejector handles and slide the SCB about halfway out of the chassis.

5. Place one hand underneath the SCB to support it and slide it completely out of

the chassis. Place it on the antistatic mat.

CAUTION: Do not stack hardware components on one another after you remove

them. Place each component on an antistatic mat resting on a stable, flat surface.

6. Repeat the procedure for each SCB.

Removing SCBs Before Installing an SRX5600 Services Gateway Without a Lift ■3

Figure 3: Removing an SCB

Removing IOCs, Flex IOCs, and SPCs Before Installing an SRX5600 Services Gateway

Without a Lift

The services gateway holds up to six IOCs, Flex IOCs, and SPCs, which are installed

horizontally in the front of the device. Each IOCs or SPC weighs up to 13.1 lb (5.9 kg),

be prepared to accept its full weight.

To remove an IOC, a Flex IOC, or an SPC (see Figure 4):

1. Have ready an antistatic mat for the card. Also have ready rubber safety caps

for each port using an optical interface on the card that you are removing.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to one of the ESD points on the chassis.

3. Label the cables connected to each port on the IOC so that you can later reconnect

the cables to the correct ports.

4. If a card uses fiber-optic cable, immediately cover each transceiver and the end

of each cable with a rubber safety cap. Arrange the disconnected cables in the

cable management system, to prevent the cables from developing stress points.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of

fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a

transceiver emit laser light that can damage your eyes.

CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting

or removing cable. The safety cap keeps the port clean and prevents accidental

exposure to laser light.

4■Removing IOCs, Flex IOCs, and SPCs Before Installing an SRX5600 Services Gateway Without a Lift

CAUTION: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc

smaller than a few inches in diameter can damage the cable and cause problems

that are difficult to diagnose.

5. Simultaneously turn both the ejector handles counterclockwise to unseat the

IOC.

6. Grasp the handles and slide the card straight out of the card cage halfway.

7. Place one hand around the front of the card and the other hand under it to

support it. Slide the IOC completely out of the chassis, and place it on the

antistatic mat or in the electrostatic bag.

CAUTION: The weight of the card is concentrated in the back end. Be prepared to

accept the full weight—up to 13.1 lb (5.9 kg)—as you slide the card out of the chassis.

When the card is out of the chassis, do not hold it by the ejector handles, bus bars,

or edge connectors. They cannot support its weight.

Do not stack cards on top of one another after removal. Place each one individually

in an electrostatic bag or on its own antistatic mat on a flat, stable surface.

Figure 4: Removing an IOC, Flex IOC, or SPC

Related Topics ■Overview of Installing the SRX5600 Services Gateway Without a Mechanical Lift

■Tools Required to Install the SRX5600 Services Gateway Without a Mechanical

Lift

■Preventing Electrostatic Discharge Damage to the SRX5600 Services Gateway

■Installing the SRX5600 Services Gateway Chassis in the Rack Manually

■Reinstalling Components in the SRX5600 Services Gateway Chassis After Installing

It Without a Lift

Removing IOCs, Flex IOCs, and SPCs Before Installing an SRX5600 Services Gateway Without a Lift ■5

■Installing the SRX5600 Services Gateway Mounting Hardware for a Rack or

Cabinet

■Moving the Mounting Brackets for Center-Mounting the SRX5600 Services

Gateway

Published: 2009-11-03

6■Removing IOCs, Flex IOCs, and SPCs Before Installing an SRX5600 Services Gateway Without a Lift

Altri manuali per SRX5600

Altri manuali Juniper Firewall

Juniper

Juniper NetScreen-5GT Wireless Manuale utente

Juniper

Juniper JSA7800 Istruzioni per l'installazione

Juniper

Juniper JSA3500 Manuale utente

Juniper

Juniper NETSCREEN-5XT Manuale utente

Juniper

Juniper JATP400 Guida all'installazione

Juniper

Juniper JATP700 Guida all'installazione

Juniper

Juniper NetScreen-5GT Wireless Manuale utente

Juniper

Juniper NETSCREEN-200 SERIES Istruzioni per il montaggio

Juniper

Juniper NetScreen-50 Istruzioni per il montaggio

Juniper

Juniper NetScreen-25 Manuale utente

Juniper

Juniper NetScreen-204 Manuale utente

Juniper

Juniper JSA7800 Guida all'installazione

Juniper

Juniper NetScreen-5000 Series Manuale dell'operatore

Juniper

Juniper NS-5400-P00A-S00 Manuale utente

Juniper

Juniper Advanced Threat Prevention Appliance Manuale di installazione

Juniper

Juniper NetScreen-50 Manuale utente

Manuali Firewall popolari di altre marche

Cisco

Cisco S190 Manuale utente

Fortinet

Fortinet FortiGate Voice Series Manuale utente

ADTRAN

ADTRAN NetVanta 2300 Manuale utente

SecureLogix

SecureLogix ETM System Manuale utente

NETGEAR

NETGEAR ProSafe FVX538 Manuale utente

Lanner

Lanner FW-8877 Manuale utente

Huawei

Huawei USG6000 Series Manuale di installazione e funzionamento

H3C

H3C SecPath F5000-AI-15 Manuale utente

Nexcom

Nexcom DNA 1150 Manuale utente

Fortinet

Fortinet FortiGate-60 series Manuale utente

Cisco

Cisco 3110 Manuale

Draytek

Draytek Vigor2860 Series Manuale utente

Lanner electronics

Lanner electronics FW-7650 Series Manuale utente

Swisscom

Swisscom Internet Backup Manuale utente

SonicWALL

SonicWALL NSa 5700 Manuale utente

DPtech

DPtech FW1000 SERIES Manuale utente

FEITIAN

FEITIAN MultiPass FIDO Manuale utente

EBLOCKER

EBLOCKER PRO Manuale utente