Juniper SRX650 Manuale utente

Connecting the SRX650 Services Gateway to the DC Power Supply

CAUTION: Do not mix AC and DC power supplies within the same services gateway.

Damage to the device might occur.

The 645 W DC power supply with PoE support is available for the SRX650 Services

Gateway.

WARNING: Before performing the following procedure, ensure that power is removed

from the DC circuit. To ensure that all power is off, locate the circuit breaker on the

panel board that services the DC circuit, switch the circuit breaker to the off position

(O), and tape the switch handle of the circuit breaker in the off position.

You connect DC power to the device by attaching power cables from the external

DC power sources to the terminal studs on the power supply faceplate. You must

provide the power cables (the cable lugs are supplied with the services gateway).

To connect the DC source power cables to the services gateway power supply:

1. Switch off the dedicated facility circuit breakers. Ensure that the voltage across

the DC power source cable leads is 0 V and that there is no chance that the cable

leads might become active during installation.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to the ESD point on the side of the chassis.

3. Remove the clear plastic cover protecting the terminal studs on the faceplate.

4. Verify that the DC power cables are correctly labeled before making connections

to the power supply. In a typical power distribution scheme where the return is

connected to chassis ground at the battery plant, you can use a multimeter to

verify that the ohm output of the –48V and RTN DC cables to chassis ground.

The cable with very large resistance (indicating an open circuit) to chassis ground

will be –48V and the cable with very low resistance (indicating a closed circuit)

to chassis ground will be RTN.

CAUTION: You must ensure that power connections maintain the proper polarity.

The power source cables might be labeled (+) and (–)to indicate their polarity. There

is no standard color coding for DC power cables. The color coding used by the external

DC power source at your site determines the color coding for the leads on the power

cables that attach to the terminal studs on the power supply.

5. Remove the screws and square washers from the terminals. Use a number 2

Phillips screwdriver.

6. Secure each power cable lug to the terminals, first with the square washer, then

with the screw. Apply between 23 lb-in. (2.6 Nm) and 25 lb-in. (2.8 Nm) of torque

to each screw.

Connecting the SRX650 Services Gateway to the DC Power Supply ■1

■Secure each positive (+) DC source power cable lug to a RTN (return)

terminal.

■Secure each negative (–) DC source power cable lug to a –48V (input) terminal.

7. Replace the clear plastic cover over the terminal studs on the faceplate.

8. Verify that the power cables are connected correctly, that they are not touching

or blocking access to services gateway components, and that they do not drape

where people could trip on them.

NOTE: The services gateway must be connected to earth ground during normal

operation. The protective earthing terminal on the side of the chassis is provided to

connect the services gateway to ground.

CAUTION: We recommend using a surge protector for the power connection.

Related Topics ■Preventing Electrostatic Discharge Damage to the SRX650 Services Gateway

■Grounding the SRX650 Services Gateway

■Organizing Interface Cables on the SRX650 Services Gateway

■SRX650 Services Gateway General Safety Guidelines and Warnings

Published: 2010-02-01

2■Connecting the SRX650 Services Gateway to the DC Power Supply

Altri manuali per SRX650

5

Indice

Altri manuali Juniper Portale

Juniper

Juniper SRX220 Manuale utente

Juniper

Juniper SRX345 Manuale utente

Juniper

Juniper SRX3600 Manuale utente

Juniper

Juniper SRX5600 Manuale utente

Juniper

Juniper SRX 5800 Manuale utente

Juniper

Juniper SRX345 Manuale utente

Juniper

Juniper SRX380 Istruzioni per l'installazione

Juniper

Juniper MAG2600 Istruzioni per l'installazione

Juniper

Juniper SRX5600 Manuale utente

Juniper

Juniper SRX100 Istruzioni per l'installazione

Juniper

Juniper SSG20 Manuale utente

Juniper

Juniper SRX 210 Manuale utente

Juniper

Juniper SRX240 Series Manuale utente

Juniper

Juniper SSG140 Istruzioni operative e di sicurezza

Juniper

Juniper SRX3600 Manuale utente

Juniper

Juniper SRX220 Istruzioni per l'installazione

Juniper

Juniper SRX5600 Istruzioni per l'installazione

Juniper

Juniper SRX110 Manuale utente

Juniper

Juniper SRX5600 Manuale utente

Juniper

Juniper SRX4200 Istruzioni per l'installazione

Juniper

Juniper SSG5 Manuale utente

Juniper

Juniper SRX 3400 Manuale utente

Juniper

Juniper SRX 1400 SERVICES GATEWAY - Manuale utente

Juniper

Juniper SRX 210 Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente