Juniper JCS 1200 Manuale utente

Replacing a JCS 1200 Management Module or Module Filler

Topics include:

■Removing a JCS 1200 Management Module or Module Filler on page 1

■Installing a JCS 1200 Management Module or Module Filler on page 2

Removing a JCS 1200 Management Module or Module Filler

Figure 1 on page 1 shows how to remove and install a management module.

Figure 1: Removing and Installing a JCS 1200 Management Module

When you remove a management module, keep in mind the following:

■These instructions assume that the JCS 1200 platform is connected to power.

■If you are replacing the only management module in the JCS 1200 platform and

the management module is functioning, save the configuration file before you

proceed. For information about saving and restoring a configuration file, see the

JUNOS Protected System Domain Configuration Guide.

■If you have just installed a second management module in the JCS 1200 platform,

do not remove the first (primary) management module for up to 45 minutes;

the second (redundant) management module needs the time to receive initial

status information and firmware from the management module.

To remove a management module or module filler (see Figure 1 on page 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Pull the management module release handle to the open position. The module

moves out of the bay approximately 0.25 in. (0.6 cm).

3. Slide the management module out of the bay.

Replacing a JCS 1200 Management Module or Module Filler ■1

Installing a JCS 1200 Management Module or Module Filler

Figure 2 on page 2 shows how to remove and install a management module.

Figure 2: Removing and Installing a JCS 1200 Management Module

To install a management module or module filler (see Figure 2 on page 2):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Remove the management module filler, if one is installed.

3. Remove the management module interposer filler tray, if one is installed.

4. Install the management module interposer, if it is not already installed.

5. Make sure that the release handle on the management module is in the open

position.

6. Slide the management module into the management module bay until it stops.

7. Push the management module release handle to the closed position.

8. Connect any cables to the management module.

9. If the JCS 1200 platform is connected to power, make sure that the OK LED on

the management module is lit. If the management module is redundant, wait at

least 45 minutes for the modules to copy the configuration data before you make

any changes to the management module configuration.

Related Topics ■Preventing Electrostatic Discharge Damage to the JCS 1200 Platform

■JCS 1200 Management Module Description

■Replacing a JCS 1200 Management Module Filler Tray

■Locating the JCS 1200 Management Module Serial Number

2■Installing a JCS 1200 Management Module or Module Filler

Altri manuali per JCS 1200

6

Indice

Altri manuali Juniper Router di rete

Juniper

Juniper MX Series Manuale utente

Juniper

Juniper M120 Istruzioni per l'installazione

Juniper

Juniper ACX2200 Istruzioni per l'installazione

Juniper

Juniper M10i Manuale utente

Juniper

Juniper PTX10003-80C Istruzioni per l'installazione

Juniper

Juniper J2320 Manuale utente

Juniper

Juniper ACX4000 Manuale utente

Juniper

Juniper MX10008 Istruzioni per l'installazione

Juniper

Juniper QFX5100 Istruzioni per l'installazione

Juniper

Juniper ACX1000 Manuale utente

Juniper

Juniper EX9200 Series Scheda tecnica

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV... Manuale utente

Juniper

Juniper MX960 Istruzioni per l'installazione

Juniper

Juniper E-Series Istruzioni per l'installazione

Juniper

Juniper MX480 Istruzioni per l'installazione

Juniper

Juniper M5 Manuale utente

Juniper

Juniper T640 Istruzioni per l'installazione

Juniper

Juniper MX2020 Istruzioni per l'installazione

Juniper

Juniper M10i Istruzioni per l'installazione e il funzionamento

Juniper

Juniper EX4600 Manuale utente

Juniper

Juniper MX10016 Manuale utente

Juniper

Juniper MX2008 Istruzioni per l'installazione

Juniper

Juniper J-Series Manuale utente

Juniper

Juniper CTP2000 Series Manuale dell'operatore

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza