Jura Impressa J6 Manuale utente

J6/J600 – Quick Reference Guide

These short instructions do not replace the ‘J6/J600 Instructions for

Use’. Make sure you read and observe the safety information and

warnings first in order to avoid hazards.

You can initiate the rinse operation manually at any time.

TPlace a receptacle under the coffee spout.

TPress the P button.

‘Maintenance status’

TPress the Rotary Switch.

‘Clean’

TTurn the Rotary Switch until ‘Rinse’ is displayed.

TPress the Rotary Switch to initiate the rinse operation.

‘Machine is rinsing’, ‘Milk system is being rinsed’, water

flows out of the coffee spout.

The rinse stops automatically. ‘Please select product’

appears on the display.

15 minutes after milk preparation, the milk system is automatically

rinsed. Therefore always place a receptacle under the cappuccino

frother after preparing milk.

When ‘Rinse the milk system’ is displayed, you can start rinsing by

pressing the Rotary Switch.

Rinsing the machine

Automatic milk system

rinsing

J6/J600 – Quick Reference Guide

To ensure that the cappuccino frother always works properly, you

must clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

EJURA milk system cleaner is available from specialised dealers.

ETo clean the milk system, use the container supplied.

TPress the P button.

‘Maintenance status’

TPress the Rotary Switch.

‘Clean’

TTurn the Rotary Switch until ‘Clean the milk system’ is dis-

played.

TPress the Rotary Switch.

‘Clean the milk system’

TPress the Rotary Switch again.

TPress the ‘Start’ button.

TRemove the milk pipe from the milk container or carton.

TAdd milk system cleaner to the front part of the container

up to the bottom mark (indicated by 6).

TThen fill with water up to the upper mark.

TPlace the container under the cappuccino frother.

TTurn the setting wheel of the cappuccino frother to the Milk

position z.

TConnect the milk pipe to the container.

ETo connect the milk pipe to the container correctly, the pipe

must be fitted with a connector.

TPress the ‘Next’ button.

‘Milk system is being cleaned’ appears and the cappuccino

frother and the milk pipe are cleaned.

Cleaning the milk system

CAUTION

J6/J600 – Quick Reference Guide

TDuring the first brief interruption, set the setting wheel of

the cappuccino frother to the Milk Foam position 5.

‘Water for cleaning milk system’

TRinse the container thoroughly and fill the front part with

fresh water up to the upper mark.

TPlace this under the cappuccino frother and reconnect the

milk pipe to the container.

TPress the ‘Next’ button.

‘Milk system is being cleaned’ appears and the cappuccino

frother and the milk pipe are rinsed with fresh water.

The start screen is displayed.

To make sure the cappuccino frother works properly, and in the inte-

rests of hygiene, it must be dismantled and rinsed daily if you have

been preparing milk.

TRemove the milk pipe and rinse it thoroughly under running

water.

TCarefully pull the cappuccino frother down and off.

TDismantle the cappuccino frother into its individual parts.

TRinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts

in a solution of 250 ml cold water and 1 capful of JURA milk

system cleaner. Then rinse the parts thoroughly.

TReassemble the cappuccino frother.

EEnsure that all individual parts are correctly and firmly con-

nected to ensure correct operation of the cappuccino frother.

TFirmly attach the frother to the connector.

Dismantling and rinsing

the cappuccino frother

J6/J600 – Quick Reference Guide

Your JURA no longer has to be descaled if you are using the CLARIS

Smart filter cartridge. If you did not insert the filter cartridge the first

time you used the machine, you can do this now as follows.

TPlace a receptacle under the hot-water spout.

TRemove and empty the water tank.

TOpen the filter holder.

TFit the filter cartridge extension supplied on top of a CLARIS

Smart filter cartridge.

TInsert the filter cartridge with its extension into the water

tank.

TClose the filter holder. It will click into place audibly.

TFill the water tank with fresh, cold water and reinsert the

tank.

EThe machine automatically detects that you have just inserted

the filter cartridge.

‘Filter operation’ / ‘Saved’

‘Filter is being rinsed’, water flows out of the hot-water

spout.

Rinsing of the filter stops automatically after approximately

300 ml.

‘Empty drip tray’

TEmpty the drip tray and put it back into the machine.

‘Filter operation’ / ‘Filter rinsing complete’

‘Please select product’ appears on the display. Your JURA is

once more ready for use.

Inserting the filter

J6/J600 – Quick Reference Guide

EOnce the filter cartridge stops working (depending on the

water hardness setting), the JURA will prompt you to change

the filter.

ECLARIS Smart filter cartridges are available from specialised

dealers.

Precondition: ‘Change filter’ is displayed.

TPlace a receptacle under the hot-water spout.

TRemove and empty the water tank.

TOpen the filter holder and remove the old CLARIS Smart

filter cartridge and filter extension.

TFit the filter cartridge extension on top of a new CLARIS filter

cartridge Smart.

TInsert the filter cartridge with its extension into the water

tank.

TClose the filter holder. It will click into place audibly.

TFill the water tank with fresh, cold water and reinsert the

tank.

EThe machine automatically detects that you have just chan-

ged the filter cartridge.

‘Change the filter’ / ‘Saved’

‘Filter is being rinsed’, water flows out of the hot-water

spout.

‘Empty drip tray’

TEmpty the drip tray and put it back into the machine.

‘Change the filter’ / ‘Filter rinsing complete’

‘Please select product’ appears on the display. Your JURA is

once more ready for use.

Changing the filter

J6/J600 – Quick Reference Guide

After 180 preparations or 80 switch-on rinses, the JURA will prompt

you to clean it.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

EThe cleaning programme lasts approximately 20 minutes.

EDo not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

EJURA cleaning tablets are available from specialised dealers.

Precondition: ‘Clean machine’ is displayed.

TPress the P button.

‘Clean’

TPress the Rotary Switch.

TPress the ‘Start’ button.

TPress the ‘Start’ button again.

‘Empty coffee grounds container’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Press the Rotary Switch’

TPlace one receptacle under the coffee spout and another

under the cappuccino frother.

TPress the Rotary Switch.

‘Machine is being cleaned’, water flows out of the coffee

spout.

The operation is interrupted, ‘Add cleaning tablet’.

TOpen the cover of the filler funnel for ground coffee.

TInsert a JURA cleaning tablet into the filler funnel.

TClose the cover of the filler funnel.

‘Press the Rotary Switch’

TPress the Rotary Switch.

‘Machine is being cleaned’, water flows repeatedly out of the

coffee spout and the cappuccino frother.

The operation stops automatically.

‘Empty coffee grounds container’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

Cleaning is now complete. The start screen is displayed.

Cleaning the machine

CAUTION

J6/J600 – Quick Reference Guide

The JURA builds up deposits of limescale over time and automati-

cally prompts you to descale it when necessary. The degree of calci-

fication depends on the hardness of your water.

EIf you are using a CLARIS Smart filter cartridge, you will not be

prompted to descale.

If the descaling agent comes into contact with the skin or eyes, this

can cause irritation.

TAvoid contact with the skin or eyes.

TRinse off the descaling agent with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be dama-

ged and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

If the descaling operation is interrupted, there may be damage to

the machine.

TAllow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces

(e.g. marble), damage cannot be ruled out.

TClean up any splashes immediately.

EThe descaling programme lasts approximately 45 minutes.

EJURA descaling tablets are available from specialised dealers.

Precondition: ‘Decalcify machine’ is displayed.

TPress the P button.

‘Descale’

TPress the Rotary Switch.

TPress the ‘Start’ button.

TPress the ‘Start’ button again.

‘Empty drip tray’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Pour descaling agent into water tank’

TRemove and empty the water tank.

Descaling the machine

JCAUTION

CAUTION

J6/J600 – Quick Reference Guide

TCompletely dissolve 3 JURA descaling tablets in a receptacle

holding 500 ml of water. This may take several minutes.

TPour the solution into the empty water tank and insert it

into the machine.

TPlace one receptacle under the hot-water spout and another

under the cappuccino frother.

‘Press the Rotary Switch’

TPress the Rotary Switch.

‘Machine is being descaled’ appears and water flows repea-

tedly out of the hot-water spout and the cappuccino frother.

The operation is interrupted, ‘Empty drip tray’.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Fill water tank’

TRemove the water tank and rinse it thoroughly.

TFill the water tank with fresh, cold water and reinsert the

tank.

‘Press the Rotary Switch’

TPlace a receptacle under the cappuccino frother, the coffee

spout and the hot-water spout.

TPress the Rotary Switch.

‘Machine is being descaled’, the descaling operation is

continued.

The operation is interrupted, ‘Empty drip tray’.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

Descaling is now complete. The start screen is displayed.

EIf the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

J6/J600 – Quick Reference Guide

Coffee beans may be covered with a slight oil film which remains on

the walls of the bean container. These traces may negatively affect

the coffee result. For this reason clean the bean container from time

to time.

Precondition: ‘Fill bean container’ is displayed.

TSwitch the machine off with the On/Off button Q.

TOpen the bean container cover and remove the aroma

preservation cover.

TClean the bean container with a soft, dry cloth.

TFill the bean container with coffee beans, then close the

aroma preservation cover and the bean container cover.

Limescale deposits may form in the water tank. To ensure correct

function of the machine, descale the water tank from time to time.

TRemove the water tank.

TIf you use a CLARIS Smart filter cartridge, remove this.

TCompletely fill the water tank and dissolve 3 JURA descaling

tablets in it.

TLeave the water tank with the descaling solution for several

hours (e.g. overnight).

TEmpty the water tank and rinse it thoroughly.

TIf you use a CLARIS Smart filter cartridge, insert this again.

TFill the water tank with fresh, cold water and reinsert the

tank.

Cleaning the bean

container

Descaling the water tank

J6/J600_Kurz/en/201804

Altri manuali per Impressa J6

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Jura Macchina per il caffè

Jura

Jura Z10 Manuale utente

Jura

Jura IMPRESSA XS95 Manuale utente

Jura

Jura IMPRESSA C5 Manuale utente

Jura

Jura IMPRESSA X5 Manuale utente

Jura

Jura A9 Manuale utente

Jura

Jura D4 Manuale utente

Jura

Jura IMPRESSA S9 One Touch Manuale di istruzioni

Jura

Jura ENA Micro 90 Manuale utente

Jura

Jura GIGA X8 Professional Manuale di servizio

Jura

Jura IMPRESSA S70 Manuale utente

Jura

Jura IMPRESSA E80 Manuale utente

Jura

Jura IMPRESSA E80 Scheda tecnica

Jura

Jura Z6 Manuale utente

Jura

Jura GIGA W3 Professional Manuale utente

Jura

Jura IMPRESSA X9 Guida alla configurazione

Jura

Jura IMPRESSA S9 One Touch Manuale utente

Jura

Jura WE8 Manuale utente

Jura

Jura Impressa S guide Manuale utente

Jura

Jura GIGA 10 Manuale utente

Jura

Jura ENA 8 NAC Manuale utente

Jura

Jura Impressa J6 Manuale utente

Jura

Jura GIGA X7c Professional Manuale utente

Jura

Jura E6 Manuale utente

Jura

Jura ENA 8 Manuale utente

Manuali Macchina per il caffè popolari di altre marche

Taurus

Taurus Livorno 6 Manuale utente

Delta-q

Delta-q QUICK Manuale utente

Bunn

Bunn LCA-1 Guida alla risoluzione dei problemi

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Istruzioni per l'installazione

Saeco

Saeco Vienna Plus Sup 018M Manuale utente

DeLonghi

DeLonghi DC300 Manuale utente

INCAPTO

INCAPTO BXCO1470E Manuale utente

Bosch

Bosch TASSIMO finesse TAS16B Series Manuale utente

Exido

Exido 245-072 Manuale utente

Animo

Animo OptiVend Choco Manuale utente

Siemens

Siemens TQ505DF Series Manuale utente

DeLonghi

DeLonghi ECI341 Manuale utente

Krups

Krups KT406511 Manuale utente

Cimbali

Cimbali M32 Classic Manuale utente

Philips

Philips HL3844N Manuale utente

Bosch

Bosch TES 515 SERIES Manuale utente

Tekmatix

Tekmatix TMFM - 65 Manuale utente

Scarlett

Scarlett SC-CM33005 Manuale utente