JYDELAND BOBMAN SL Manuale utente
BOBMAN SL
INSTRUCTIONS
READ BEFORE USE!
UK 40-2011
1
INTRODUCTION
Thank you for your interest in the
Jydeland Bobman. We trust you
will gain a lot of satisfaction from
your purchase for many years and
that your Bobman will fulfil your
expectations.
Please read these instructions
before using the machine.
The primary functions, main-
tenance and safety will be cov-
ered in the following pages. This
is a product for professional use
only. Instructions in use of the
machine comply with the check-
list enclosed, which can also be
used for a service agreement.
If further training or a follow-up
visit are required, please contact
Jydeland A/S .
Enjoy!
2
3
WARNING
A Bobman can only be used outdoors or in
a well-ventilated room, as the exhaust gas
contains highly toxic CO².
The machine can only be operated by the
driver sitting in the driver’s seat with at least
one hand always on the steering wheel and
both feet resting on the foot rests or pedals.
Do not start machine if any covers are
removed or defective.
Not suitable for use on very hilly terrain due
to risk of tipping over. That risk is increased
significantly when appliances are attached.
Noise level for normal use exceeds 80db. The
use of ear protectors is recommended.
We recommend that the operator wears a
dust mask for spreading work.
The Bobman is for professional use by trained
personnel only.
Advarsel
4
WARNING SYMBOLS
There are yellow warning stickers on the
machine indicating where extra caution
must be exercised. These are instructions.
Always use the machine with care.
Caution! Always accompanied by another
pictogram.
Read in instruction book.
Large rotating screw conveyor. Risk of
crushing. Keep arms and legs clear. Machine
must be switched off when working on the
parts referred to by this pictogram.
Small rotating screw conveyor. Risk of trap-
ping hands. Machine must be switched off
when working on the parts referred to by
this pictogram.
Rotating blower. Machine must be switched
off when working on the parts covered by this
pictogram.
Crushing function. Risk of crushing. Keep
arms and legs clear. Exercise caution when
using this function.
Hearing protectors and goggles. Recom-
mended when operating the machine.
5
Drive
Press pedal on right
for forwards and lift
pedal for reverse.
1 WD / 3 WD
Switch between
1 and 3 wheel drive
Tipping
Handle for
unloading
hopper.
Scraper
Handle for raising, lowering
and adjustment of scraper
height.
Throttle
Engine RPM Brush
Handle for brush start and
stop. Rotation right swings at
the same time out the brush.
Rotation left makes the brush
return to transport position.
Stop in centre position.
Dosing
Handle for adjusting
the dosing of spread
material.
Operation
6
1 WD / 3 WD
Switch between
1 and 3 wheel drive
Spreadmachine
Starts and stops the
hydraulic motors for
the spreader and mixer.
Fuel
Fuel filler cap at the left
side.
Scraper
Handle for raising, lowering
and adjustment of scraper
height.
Massive hjul
Massive silicone filled wheel
as option.
Battery
12 V sealed battery under
seat. Keep terminals clean.
7
Brush
Brush weighs approx. 80 cm and can be replaced.
19 mm spanner required to adjust up and down on swing arm.
Engine arm can be turned further.
Rear of brush must be approx. 5 cm clear of ground when brushing
Accessories for different box heights can be ordered (parallelogram).
Blower
The blower nozzle can be turned downwards to direct spreading upwards or
downwards.
Baffle opening and engine RPMs determine how much material is spread!
Never put fingers, arms or objects in blower nozzle, conveyor screw and
brush if engine and hydraulics are running.
STOP machine if any foreign object blocks blower!!!
Adjusting brush Blower housing
8
Mixer can be mounted afterwards over
snail, to prevent material not getteing
to the snail.
Rubber on scraper can be replaced.
Feedturner. Extra equipment. Detachable blower spout for ex fodder
pellets. Extra equipment.
Using the Bobman spreader
1Fill hopper with sawdust or chopped straw, 3-8 cm pieces, by lowering and
driving into sawdust/straw pile.
2Lower scraper onto ribbed floor.
3Start hydraulics with handle at the left side of seat. (on/off)
4Start brush with handle at the left of the seat
5Open baffle in hopper for quantity to be spread.
Working in barn - important!
• Floor must be scraped clean twice (or more) times daily
• Bed must be swept clean and dry
• Thin layer of sawdust or chopped straw spread over bed
9
Cleaning
Always keep engine clean - use com-
pressed air if necessary. Avoid blow-
ing directly into air filter. Replace air
filter often to avoid reducing engine
power due to dust in air. The machine
can also be cleaned by high pressure
washer, but never aim jet directly at
air filter, breather pipe for hydraulics
under seat, diesel filler cap, wiring
and electronics.
Tightening up and damage
Tightening up screws and bolts must
be done regularly.
Always repair any damage immedi-
ately after discovery.
Weekly check
Check there is sufficient oil in engine
(W15-40).
Monthly check
Check level of hydraulic oil in sight
glass on right side of machine (HV32
/ HV46).
Lubrication
Lubricate steering chain with oil
(spray-on chain oil is recommended).
Lubricate ball joints with no grease
nipple and universal joint on steering
column with oil. kugleled som ikke har
nipler smøres også med olie.
Hydraulic oil
Hydraulic oil level must be in centre
of sight glass.
Replace hydraulic oil after analysis or
2000 hours.
Fill hydraulic oil (HV32 / HV46) at
filter on right side of hydraulic oil
tank.
Hydraulic oil filter
Change hydraulic oil filter first time
after 50 hours and thereafter every
500 hours or once annually. NB: if oil
colour is milky white, there is water
in the system. Change oil.
Steering
Back wheel is turned by chains from
steering wheel passing under seat.
Remove seat and top panel to adjust.
Battery
12 V sealed battery.
Keep terminals clean.
Maintenance
10
Indice
Altri manuali JYDELAND Spargitore
Manuali Spargitore popolari di altre marche
Fisher
Fisher POLY-CASTER 78601 Manuale utente
TurfEx
TurfEx RS7200 Manuale del proprietario
Ferris
Ferris Pathfinder Series Manuale utente
Fayat Group
Fayat Group DYNAPAC S100 Guida alla risoluzione dei problemi
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Manuale di installazione e funzionamento
EASTMAN
EASTMAN CR 500 Manuale utente
