K-Tool KTI-63105A Manuale utente
KTI-63105A 1
2 TON EXTRA LONG LOW PROFILE SERVICE JACK
OWNER'S MANUAL
KTI-63105A
SPECIFICATIONS
Capacity............................................................................... 2 Ton
Low Height............................................................................ 2-3/4"
High Height .............................................................................. 24"
Pump Stroked to Load............................................................... 8
Chassis Length....................................................................33-7/10"
Low Clearance Length .............................................................15"
Overall Width ........................................................................ 14-3/5"
Chassis Height....................................................................... 5-1/2"
Handle Length .................................................................... 49-1/5"
Saddle Diameter.....................................................................3-9/10"
Net Weight .....................................................................100.94 lbs.
Gross Weight .....................................................................105.8 lbs.
www.P65Warnings.ca.gov
Cancer and Reproductive Harm-WARNING:
Complies with ASME PASE/2014 Safety Standard
KTI-63105A 2
WARNING INFORMATION
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of
the device owner to keep this manual intact and in a convenient location for all to see and read.
THE NATURE OF HAZARDOUS SITUATIONS
The use of Portable Automotive Lifting Devices are subject to certain hazards that cannot be prevented by mechanical means, but only
by the exercise of intelligence, care, and common sense. It is essential to have personnel involved in the use and operation of the device
who are careful, competent, trained, and qualified in the safe operation of the device and its proper use when servicing motor vehicles
and their components. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads,
overloading, off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not intended.
METHODS TO AVOID HAZARDOUS SITUATIONS
•Read, study, understand and follow all instructions before operating this device.
•Inspect the jack before each use. Do not use jack if damaged, altered, in poor condition, leaking hydraulic or
unstable due to loose or missing components. Make corrections before using.
•Lift only on areas of the vehicle as by the vehicle manufacturer.
•User and bystanders wear eye protection that meets ANSI Z87.1 and OSHA standards.
•Do not use jack beyond its rated capacity. Do not shock load.
•This is a lifting device only. Immediately after lifting, support the vehicle with jack stands capable of sustaining the load before
working on the vehicle.
•Use only on a hard level surface free from obstructions so the jack is free to reposition itself during lifting and lowering operations.
•Center load on saddle. Be sure setup is stable before working on vehicle.
•Do not move or dolly the vehicle while on the jack.
•Do not use any materials that may serve as risers, spacers or extenders between the stock lifting saddle and the load.
•Do not use any adaptors that replace the stock lifting saddle unless approved for this device.
•Always lower the jack slowly and carefully.
•Failure to heed these warnings may result in fatal personal injury and/or property damage.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.
WARNING: Indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
WARNING
WARNING
WARNING
WARNING
KTI-63105A 3
SETUP
1. Remove 2-piece handle from box. Insert narrow portion of top handle into bottom handle, align top and bottom bolt holes, and secure
with handle bolt provided.
2. Unscrew the handle set screw #27 so that it will not interfere with the insertion of the handle in the handle socket. Insert the handle in
Secure the handle in the handle socket by tightening the handle set screw.
3. Sometimes air gets trapped in the hydraulic system during shipping and handling. If the pump feels spongy, or there is not a full
incremental pump stroke, or the jack will not raise to maximum height, follow these instructions in order to purge air from the system:
a. With the lift arm in its completely retracted position and the pump handle rotated all the way in a clockwise direction until it
stops, rotate the pump handle in a counterclockwise direction two full revolutions.
b. Proceed to pump the jack 15 full incremental pump strokes.
c. Rotate the pump handle clockwise until it stops and proceed to pump the handle until the lift arm reaches maximum height.
d. Repeat steps "A" through "C" until all air is purged from the system.
Any jack which appears to be damaged in any way, is found to be badly worn, or operates abnormally MUST BE REMOVED FROM SER-
VICE until necessary repairs are made.
INSPECTION
Handle
Bolt
Handle
Handle
Socket
Upper Handle
Bolt Hole
Lower Handle
Bolt Hole
Lower Handle
Chassis
Rear
Casters
Front
Wheels
Saddle
Lift Arm
KTI-63105A4
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death. IMPORTANT: Before attempting to raise any vehicle,
check vehicle service manual for recommended lifting surfaces.
OPERATION
1. Put vehicle transmission in park or in gear and then apply the emergency brake.
Toraiseload: Turn the handle in a clockwise direction until tight. Position the jack under the load. Proceed to pump the handle
in order to raise the lift arm to the load. As the saddle at the end of the lift arm gets closer to the load, reposition the jack so the
saddle will contact the load rmly and the load is centered on the saddle. Make sure the saddle is correctly positioned. Raise the
load to the desired work height. Place jack stands of appropriate capacity at the vehicle manufacturers's recommended support
areas that provide stable support for the raised vehicle. DONOTCRAWLUNDERVEHICLEWHILELIFTINGVEHICLEORPLACING
ORREMOVINGTHEJACKSTANDS! Once jack stands are positioned, turn the jack handle VERY SLOWLY in a counterclockwise di-
rection to lower the load to rest on the jack stands. Inspect the relationship between the jack stands and load to make sure the setup
is stable and safe. If the setup is not stable or safe, follow the preceding steps until corrected.
2. Tolowerload: Follow the procedures mentioned in "To raise load" section of the OPERATING INSTRUCTIONS in order to raise
the load off the jack stands. Once the load has cleared the jack stands, remove the jack stands from under the load and away
from the work area. DONOTCRAWLUNDERVEHICLEWHILELIFTINGVEHICLEORPLACINGORREMOVINGTHEJACK
STANDS!Turn handle very slowly in a counterclockwise direction until the load is completely lowered to the ground.
Once the jack's lifting saddle has cleared the load, remove the jack from under the load. CAUTION: Keep hands and feet away
from the hinge mechanism of the jack.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the jack in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust,
or any other harmful elements. The jack must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. The jack must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to
caster wheels, front axle, elevator arm, handle base pivot bolts, release mechanism and all other bearing surfaces. Worn parts result-
ing from inadequate or no lubrication are not eligible for warranty consideration. See page 5 for Regular Maintenance.
IMPORTANT:Inordertopreventsealdamageandjackfailure,neverusealcohol,hydraulicbrakeuid,ortransmissionoilinthe
jack.Usehydraulicjackoil,alightturbineoil,ChevronAWISO32orUnocalUnaxAW150.
3. Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external
surfaces of the jack but not any moving hydraulic components.
4. Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks
hydraulic uid. Do not use the jack if it has loose or missing hardware or components, or is modied in any way. Take corrective action
before using the jack again.
PROPER STORAGE
It is recommended that the jack be stored in a dry location with all wheels touching the ground on a relatively level surface.
TROUBLESHOOTING
Important: Service jacks are self-contained devices used for lifting, but not sustaining, a partial vehicular load. In accordance with ASME-
PALD Load Sustaining Test: “A load not less than the rated capacity…shall not lower more than 1/8" (3.18mm) in the rst minute, nor a
total of .1875" (4.76mm) in 10 minutes.” Lowering within this range is considered normal operation and is NOT a warrantable defect.
PROBLEM:UNITWILLNOTLIFTRATEDLOAD.
ACTION: Purge air from hydraulic system by following procedure under SETUP.
PROBLEM:UNITWILLNOTSUSTAINRATEDLOADORFEELS"SPONGY"UNDERRATEDLOAD.
ACTION: Purge air from hydraulic system as above.
PROBLEM:UNITWILLNOTLIFTTOFULLHEIGHT.
ACTION: Purge air from hydraulic system as above or check oil level in reservoir.
PROBLEM:HANDLETENDSTORAISEUPWHILETHEUNITISUNDERRATEDLOAD.
ACTION: Pump the handle rapidly several times to push oil past ball valves in power unit.
KTI-63105A 5
IMPORTANT: Service jacks are designed for lifting purposes only; always support raised load with jack stands.
REGULAR MAINTENANCE
MONTHLY or as necessary (depending on usage)
#1
(Use a multi-purpose NLGI type grease only.)
#2 Lubricate all linkages and pivot points.
(Use white lithium spray grease only.)
#3 Remove handle; lubricate handle receptacle and handle end.
(Use white lithium spray grease only.)
#4 Lubricate both rear casters bearings and both front wheels.
(Use white lithium spray grease only.)
Tighten all accessible hardware.
HYDRAULIC MAINTENANCE GUIDE
#1
#2
#2
#3
#4
#4
#3
#2
KTI-63105A 6
WARRANTY
Michigan
K-Tool International warrants that all jacks and service-related equipment will be free from defects in material and workmanship for a
period of 2 years following the original date of purchase. This warranty is extended to the original retail purchaser only. If any jack or
service-related item proves to be defective during this period, it will be replaced or repaired, at K-Tool International’s option, without
charge. This warranty does not apply to damage from accident, overload, misuse or abuse, nor does it apply to any equipment which
has been altered or used with special attachments other than those recommended.
K-Tool International HD and XD service-related equipment 2 Year Limited Warranty.
KTI-63105A 7
2 TON EXTRA LONG LOW PROFILE SERVICE JACK
EXPLODED DRAWING
KTI-63105A
1 0
12
3
4
5
6
7
8
9
1 1
1 3
1 4
1 2
1 6
1 5
1 7
1 8
1 9
2 0
2 1 2 2
2 3
1 9
2 0
2 4
2 6
2 7
2 8
2 9
3 0
3 1
3 2
3 3
3 4
3 5
3 6
3 8 3 7
3 9
4 0
4 1
2 5
4 3
4 4
4 2
3 3
KTI-63105A 8
2 TON EXTRA LONG LOW PROFILE SERVICE JACK
KTI-63105A
PARTS LIST
*Available in KT63105AHRK - Hydraulic Repair Kit
REF. # PART # DESCRIPTION REF. # PART # DESCRIPTION
1 C ring 24 Cotter Pin
2 Washer Washer
3 Front Wheel Handle Socket
Left Side Plate4 27 Bolt
C ring5 Roller
Rod Link6 Roller Axle
7 Rod Link Axle 30 Limit Rod
8 Lift Arm 31 Handle Socket Limit Rod
9 Saddle 32 Nut
10 Lower Handle Part 33 Washer
Hex Bolt11 34 Rear Wheel Unit
Up Handle Part21 35 Reinforce Rod
13 M6 Grease Nipple 36 Washer
14 C ring Washer
Cotter Pin51 38 Inner Hex Bolt
16 Cover 39 Washer
17 Bolt 40 Inner Hex Bolt
18 Rod Link Bolt 41 Lift Arm Axle
19 Handle Socket Bolt 42 C Ring
20 Washer 43 Nut
21 Return Spring 44 Hook
22 Pump Unit
23 Rod Link
37
25
26
28
29
KTP63105A03
KTP63105A09
KTP63105A12
KTP63105A10
KTP63105A21
KTP63105A22
KTP63105A26
KTP63105A34
Indice
Altri manuali K-Tool Jack
K-Tool
K-Tool KTI-63517A Manuale utente
K-Tool
K-Tool KTI63500 Manuale utente
K-Tool
K-Tool XD KTI63101 Manuale utente
K-Tool
K-Tool KTI63131A Manuale utente
K-Tool
K-Tool KTI-63131B Manuale utente
K-Tool
K-Tool KTI63092 Manuale utente
K-Tool
K-Tool KTI63100 Manuale utente
K-Tool
K-Tool PRO Series Istruzioni per l’uso
K-Tool
K-Tool KTI63105 Manuale utente
K-Tool
K-Tool XD KTI-63133A Manuale utente
