K9Safety K9Caller Foglio di istruzioni

Configuration Manual

K9Caller™

Phone: 877-K9-SAFE-T

Phone: 877-597-2338

Located in Glendale, AZ

www.K9Safety.com

K9Caller™firmware v56

Page 2

Selecting Features and Connections.

In the following section we will identify the connections and programming for the

most common system configurations that are being used by our K9Caller custom-

ers.

The two most common uses of the K9Caller are found in but not restricted to

Police Patrol K9 Vehicle (Professional Handler) & Privately Owned Vehicle

(Dog Enthusiast) .

The K9Caller can be configured to operated in a number of fashions depending on

the user or agencies needs. Some of the system’s features can be selected from the

remote at any time while others are selected through the programmable branches.

Your preferences may also require the system to have some of the connections

wired to the vehicle in a particular fashion or with optional modules to achieve the

desired results though most of the connections are standard from vehicle to vehi-

cle. Some of the features that would require specific wiring or optional modules

include connecting any of the three aux channel outputs, Aux1, Aux2 and Trunk/

Door pop, or window modules, fans, and cellular messenger. Optional hardware

is typically necessary to achieve door pop functionality (door pop kit upgrade)

which will receive a command from the system to pop open the door.

It is helpful to review the options available in the programmable branches to make

the best determination as to the features that are desired and the wires or options

that will be connected on your vehicle.

Some of the features should only be changed by a qualified technician.

These features are denoted with Tech.

Other feature can be changed by the user and they are denoted with User.

See Branch Programming for details

Selecting Features and Connections Continued.

Police Patrol K9 - Professional Handler

This is the most common configuration for police agencies across the country. By

default the system comes programmed to operate in this fashion.

Features

The K9 systems will automatically turn on and monitor for temperature whenever

the vehicle arrives at a destination. If the temperature inside the vehicle reaches the

start temperature, the engine will start allowing the AC to operate. If the vehicle

reaches the alert temperature, the vehicles horn will honk and an alert message will

be sent to the LCD remote. If the optional window module is installed, the win-

dows will roll down during hot temperature alert. If the optional window fan is in-

stalled, the windows fan will turn on during hot temperature alert. The remote can

also be used to manually turn on/off the car alarm and lock and unlock the doors. If

the door pop kit is installed the LCD or 1way remote can be used to pop the door.

Aux1 can be wired with an optional relay to pop the trunk open.

Another feature is the starter disable/starter anti-grind which requires the connec-

tion of the included relay and will disable the vehicle from being started when the

security alarm is active and will also prevent the starter from grinding if the vehicle

is “auto-started”and the user turns the ignition key to the start position.

Note, police K9 vehicles normally have fixed inserts and window screens that

would prevent the dog from jumping out of the window and would also keep the

vehicle secure from intrusion.

Privately Owned Vehicle -Dog Enthusiast)

This is the most common configuration for users of privately owned vehicles that

have a canine companion travel with them. The default settings are typically

changed in branch programming to have manual K9 system activation selected.

Features

Consumer installations can be slightly different in nature as most consumers do not

want windows to roll down automatically as this could put their canine at risk of

injury or their vehicle at risk of unlawful entry. This simply means that an optional

window drop module would not be installed on the vehicle. The more likely option

would be the bidirectional window controller that can be connected to the aux out-

puts to remotely roll up and down the windows. Many consumer vehicles are

equipped with additional features such as automatic door sliders and rear hatch or

trunk pops that can also be connected to one of the three aux outputs.

Page 3

Page 4

// Button1/ Button2/ Button3/ Button4

Branch1 // Passive/ Manual K9System Activation * User

Branch2 // 95f/ 90f/ 100f/ Hot Alert Temperature * User

Branch3 // Horn/ Siren/ Both Temperature Alert Warning User

Branch4 // 15min/ 5min/ 10min/ Disable Remote Temperature Poll User

Branch5 // 5Min/ 7Min/ 10Min Alert Delay Timer User

Branch6 // Enable/Disable K9SystemAutoOn Pin S4 Tech

Branch7 // TemperatureAutoStart/ EasyIdle Engine Controller User

Branch8 // 75f/ 80f/ 85f Hot Start Temperature * User

Branch9 // No Selection

Branch10 // Door Pop/ Trunk Pop Output Selection Pin M1 Tech

Branch11 // 5deg/ 10deg/ 2deg Hot Start Hysteresis. User

Branch12 // External Pop receiver/ Sensor Input Pin 2 Tech

Branch13 // Disable/ Enable Remote Feature Lockout Tech

Branch14 // Enable/ Disable Disarm before PinM1 Tech

Branch15 // Disable/ Enable Rearm after PinM1 User

Branch16 // FactoryAlarmDisarm/ Ignition Output Pin M10 Tech

Branch17 // Pulse/ Timed/ Latched/ HotStart Aux1 Output Pin A7 Tech

Branch18 // Pulse/ Timed/ Latched/ Hot Alert Aux2 Output Pin A6 Tech

Branch19 // Manual/ Passive Alarm Arming User

Branch20 // Disable/ Enable Auto Alarm Rearm User

Branch21 // Siren/ Both/ Silent Arming Chirps * User

Branch22 // No Selection

Branch23 // Single/ Double Door Unlock Pulse Tech

Branch24 // 1 Second/ 3 Seconds Door Lock Pulse Length Tech

Branch25 // Disable/ Enabled Passive Door Locking Tech

Branch26 // Disable/ Enable Lock After Start Tech

Branch27 // Disable/ Enable Lock After Shutdown Tech

Branch28 // Normal/ Extended/ SuperExtended Smart Start Crank Time Tech

Branch29 // Enable/ Disable Smart Start Temperature Compensation Tech

Branch30 // SmartStart/ Tach Engine Sense Mode Tech

Branch31 // RPMLearnTach/ GasEngine/ DieselEngine Program Engine Tech

Branch32 // Acc/ Ignition Pin i3 Output Type Tech

Branch33 // Negative/ Positive Wait to Start Input Type Tech

Branch34 // Enable/ Disable Turbo Timer Tech

Branch35 // Enable/ Disable Open Door Report Tech

*Asterisk denotes that the feature can be changed on the remote menu

User denotes that the feature can be changed by the user.

Programmable Branches/Features

Page 6

There are 35 installer programmable options that affect the way the system will operated.

These features can be changed at any time by entering feature programming mode. There is

also a factory reset function that allows the installer to quickly return the features to their

default setting. Please refer to your installer or installation guide for changing feature set-

tings.

Branch 1 Passive/Manual K9System

This function determines whether the K9 portion of the system will automatically turn the

monitoring state on whenever the vehicle arrives at a destination. Arrival is detected when

the vehicle transmission is shifted into park and the brake pedal is released.

Branch 2 Hot Temperature Alert Threshold

This is the programmable temperature setting that determines at what temperature the alert

outputs will be triggered. There are 3 factory settings that can be selected via this feature.

You can also change this setting via the remote control. See Remote Controls ( h° )

Branch 3 Temperature Alert Warning

This is the setting to select the audible alert output. The alert can trigger the horn, alarm

siren or both.

Branch 4 Automatic Temperature Poll

The system can be set to automatically send a temperature update to the remote at regular

intervals.

Branch 5 Alert Delay Timer

The alert delay timer controls the intervals at which the alert signal is sent to the remote and

the duration of delay for the alert delay function.

Branch 6 Pin S4 K9system Auto On

This setting selects the operation of the white wire on pin S4 as a trigger to automatically

turn on the K9system (dog in car sensor or pressure mat).

Branch 7 Temperature Engine Start/Easy Idle

This feature selects whether or not the system will automatically start the vehicle based on

temperature or automatically activate the Easy Idle feature. In Easy Idle the system will

keep the engine running every time the vehicle arrives at a destination. Step on the brake

pedal to shut the engine. Remote Start will still function in easy idle.

Programming Branch Description Explained

Branch 8 Hot Temperature Start Setting

This is the programmable temperature setting that determines at what temperature the system

will start the vehicle based on High temperature. There are 3 factory settings that can be se-

lected via this feature. You can also change this setting via the remote control. See Remote

Controls ( c° )

Branch 9 No Selection

Branch 10 Door/TrunkPop Output Selection (Pin M10)

This setting selects whether the Aux 1 output will be used as a door pop or a trunk pop. As a

door pop, Aux 1 can only be triggered when the K9system is Activated and a valid signal is

received. As a trunk pop, Aux 1 will be triggered whenever a valid signal is received. Note,

the polarity can be changed between negative and positive depending on the jumper setting.

See Fig J1 on page 9. If you require door pop and trunk pop then use one of the aux channels

to perform trunk pop.

Branch 11 Hot Start Hysteresis

Hysteresis is an offset that determines the shutdown temperature for temperature activated

auto start. The default is 5 degrees which means if the start temperature is set to 75 degrees

then the cabin has to cool to 70 degrees before the engine will shut off.

Branch 12 Sensor Input/External Pop receiver

This setting selects whether Pin S2 Blue wire will act as a door pop trigger (Pro) when the K9

system is activated or as a alarm sensor input.

Branch 13 Remote Feature Lockout

This feature selects whether all the functions can be processed from the remote or only certain

ones. In lockout mode, the remote will not activate/deactivate the K9 system, change hot start,

or hot alert temperature.

Branch 14 Disarm before Pop/Trunk Output (Pin M1)

This feature selects if the system will disarm the alarm system before a door pop or trunk pop

to prevent the alarm from being triggered.

Branch 15 Rearm after M1 Pop Output

This feature selects if the system will rearm the alarm system after a door pop or trunk pop

Branch 16 Factory Alarm Disarm/Ignition

This setting chooses the type of output for Pin M10 between a factory disarm output or an

ignition output. Note, the polarity can be changed between negative and positive depending on

the jumper setting. See Fig J1 on page 9.

Programming Branch Description, Continued

Page 7

Page 8

Branch 17 Aux 1 Mode

This is to select the type of output for Aux 1 Pin A7. The selection can be pulsed, timed for

10 seconds, latched on/off, or during hot start.

Branch 18 Aux 2 Mode

This is to select the type of output for Aux 2 Pin A6. The selection can be pulsed, timed for

10 seconds, latched on/off. Aux 2 can also be selected to supply an output if the Hot Alert

temperature has been reached even if the K9 system is not activated (can be used for indica-

tion while driving or fail safe.

Branch 19 Manual/Passive Alarm Arming

This is to select the alarm arming feature between manual (remote only) and passive (auto

armed after last door closes)

Branch 20 Auto Alarm Rearming

When selected, the system will automatically re-arm 30 seconds after it is disarmed .

Branch 21 Arming Chirps

Selects whether the siren will chirp when the alarm system is armed/disarmed. This function

can also be changed via the remote. See

Branch 22 No Selection

Branch 23 Door Unlock Pulse

Selects between one pulse or two pulse operation for the door unlock output. Many new im-

port vehicles’factory door locking systems require two pulses on the proper wire to unlock

the doors.

Branch 24 Door Lock Pulse Length

Selects between a 1, 3 or 0.1 seconds output for door locking and unlocking. Program to 3

seconds for vehicles equipped with vacuum door locking systems.

Branch 25 Passive Door Locking

Selects whether or not the system will automatically lock the doors during Passive Arming.

Branch 26 Lock after Start

When selected, the doors will automatically lock after remote starting.

Branch 27 Lock after Shutdown

When enabled, the doors will automatically lock after remote shutdown.

Programming Branch Description Continued

Branch 28 Smart Start Crank Time

Selecting engine crank time automatically selects the tachless mode and one of three crank

times. If the normal engine crank time is too short increase the time by selecting one of the

two additional extended crank time options. Normal - 0.8Sec., Extended - 1.0Sec., Super Ex-

tended - 1.4Sec. Tachless Mode. Determines the engine status using an advanced software

routine, without requiring connection to the vehicle’s tachometer. Tachless operation may not

be compatible with some vehicles or in severe temperatures, in which case the tach wire must

be connected.

Branch 29 Smart Start Temp. Comp.

Adjusts crank time to compensate for temperature variations.

Branch 30 Engine Sense Mode Smart Sense/Tach Mode

Selects between Smart Sense or Tach mode. Note Tach mode is the preferred method of sens-

ing engine run

Branch 31 Remote Start Program

This dual program branch sets the engine mode for Gas or Diesel, and learns the vehicle’s

RPM threshold. For installation into a diesel equipped vehicle, first set the engine type to

diesel before learning RPM. RPM Learn/Tach Monitor. start the engine, enter Branch 21, the

LED light will flash continuously to indicate it is reading the tach signal. Press Button 1 to

learn the vehicle’s tach signal. The siren will chirp and the LED will flash once to confirm

learning of the tach signal. The siren will chirp four times and the LED will flash four times if

the tach signal was not learned. Tach Monitor mode: monitors the vehicle’s tach wire (or a

fuel injection wire) in real-time to determine engine status and adjust starter crank time auto-

matically. Gas Engine. Sets the engine type for Gasoline. Diesel Engine. Sets the engine type

for Diesel and monitors the glow plug input to make sure the glow plugs are warm before

cranking the starter. If the glow plug wire is not connected, the built-in timer waits 15 seconds

before automatically cranking the starter.

Branch 32 Acc/Ignition Output (Pin i3)

This setting selects whether the system will output an accessory signal or ignition signal to Pin

i3 brown wire.

Branch 33 Wait to Start Input

Selects between negative and positive input polarity on Pin A4

Branch 34 Turbo Timer

When enabled, if the emergency brake has been applied Ignition power will be kept On for a

predetermined time (2 minutes Factory Default) upon arrival.

Branch 35 Ignore Open Door Report

Bypasses the open zone warning chirps for vehicles equipped with a residual dome light cir-

cuit that remains on for a period of time after closing the door.

Page 9

Phone: 877-K9-SAFE-T

Phone: 877-597-2338

Located in Glendale, AZ

A Better Breed of Systems™

K9Safety warrants that all K9Safety products are free from defects in workmanship

and materials from the factory. K9Safety will repair or replace any part or parts that

K9Safety has examined and that K9Safety is satisfied were originally defective. Defective

parts must be returned to K9Safety accompanied by a copy of the corresponding K9Safety

invoice with transportation charges prepaid within one year of the date of purchase.

This warranty is void if the products or parts have been subject to improper installation,

misuse, accident, negligence, or unauthorized service. This warranty is void if the unit(s)

have been modified or if the unit(s) are used in a fashion not intended by K9Safety. This

warranty does not cover service or labor charges that may be incurred during replacement

or repair.

K9Safety will not be responsible for expense, loss, or damage caused indirectly or di-

rectly by the use of K9Safety products, or any other cause.

No person, dealer or agent is authorized to make modifications or additions to this warranty

or to assume any other liabilities on behalf of K9Safety.

Removing or defacing serial numbers or other identification, or accessing internal compo-

nents will void the warranty stated above.

The rights granted to you by this warranty may be supplemented or restricted by state law.

Altri manuali per K9Caller

Altri manuali K9Safety Avviamento remoto

K9Safety

K9Safety K9Caller Manuale utente

Manuali Avviamento remoto popolari di altre marche

AstroStart

AstroStart 803U Manuale utente

Durite

Durite 0-649-20 Manuale

EINHELL

EINHELL BT-PS 1000 Manuale

Linear

Linear ACCESS AK-21 Specifiche tecniche

Soundstream

Soundstream TARANTULA RS.2 Manuale utente

Jaycar Electronics

Jaycar Electronics MB3752 Manuale utente

Ultra Start

Ultra Start 72 Series Manuale utente

ADS

ADS FLASHLOGIC FLRSVW1 Manuale utente

Selecta

Selecta JS012 Manuale utente

Black Widow Security

Black Widow Security BW RAS 400 Manuale utente

Vector

Vector Power City DK080706 Supplemento

Code Alarm

Code Alarm CA-535 Manuale utente

Ozito

Ozito OJS-800 Manuale utente

Profi-Partner

Profi-Partner 46387 Manuale utente

EZ STARTER

EZ STARTER EZ-45 Manuale utente

Viper

Viper 4204 Manuale utente

Essex Electronics

Essex Electronics KE-1701 Manuale utente

EINHELL

EINHELL EGS 3600 Manuale