KAISDA K2 Manuale utente
KAISDA E bike
USER Manual
(Eglish, Deutsch, italiano, français, español)
Have CE, UKCA Certificate
KAISDA
Instruction Manual
CAUTION: Reading the instructions carefully before using the KAISDA electric bike !
Contents
Safety instruction Page1
instruction
-----------
-----------------------------------------------------Page 1
Dispiay operation
--------------------------------------------------------
Page 2-3
Battery related information and maintenance
----------------------------------Page 3
The charging metho
Page 3-4
Installation Instruction
Page 4-9
-
1
-
1.Safety Instruction
1. Thank you for purchasing the KAISDA E-BIKE. The E-BIKE features the most
recent innovation in technology.
2. For Safety reasons, it is most important that you read this user’s manual before
you operate the bike. Improper handling can reduce its riding performance and most
importantly, cause danger to your safe and healthy.
3. For handling and maintenance of the bicycle, please refer to the E-BIKE user’s
manual which is an integral part of this e-bike user’s manual!
4. Do not at any time dismantle or disassemble any of the above e-bike components!
5. Please check all parts are tighten and locked before riding.
6. Please make sure that the battery charger and charging plug are always kept dray
and never get wet.
7. When charging, do not place the charger and battery in the direct sunlight or high
temperature place.
8. The charger should only be cleaned with a dry cloth. Never use a wet cloth, oil or
any other liquid.
2. Instruction
3.Display operation
2.1Open the Display
Long press Button show "OPEN" for 2-3 seconds to boot, short press button "+ -
"1-5 gear adjust the speed of the E-BIKE.
3.1
2.2 Functional Layout Interface of Display (More details can contact us to get
the display instruction manual)
3.2
-2-
average speed 25km/h can continue to travel for a long
distance.
conditions and battery capacity. However, under the same conditions, the
1. How far can a fully charged battery go? It depends on load weight, road
important to place a fully charged battery on a dry, flat surface.
2. When storing batteries for an extended period of time (such as in winter), it is
2.3 Precautions for Operation
Pay attention to safe use. Do not attempt to untie the connector when connecting the
battery.
●Avoiding collision risk.
●Do not modify system parameters to avoid parameter clutter.
●Instrumentation error code should be repaired in time.
4. Battery related information and maintenance
3. Note: when the battery is not in use, it should be charged every 1-2 months.
4.Warning:
3.1. Please keep the battery out of reach of children.
3.2. Do not attempt to turn on the battery.
3.3. If the battery is damaged in a crash or cycling accident, there is a risk of
electrolyte leakage. Beware of chemical burns! And immediately stop using
damaged batteries.
4.4 Do not touch the battery without a cloth or gloves, and make sure the acid
does not touch your eyes.
4. 5.The charging method
1.When the battery of an electric bicycle needs to be charged, just put the bicycle in
the place where the power supply can reach it. First, connect the charging plug of the
charger to the charging seat on the battery, and then plug in the power plug of the
charger to charge.
2.
placed in a convenient place for charging.
-3-
The battery can be installed on the bicycle for charging, or it can be taken out and
2.1 Open the folding buckle of the riser. After the riser is aligned with the slot of the
riser, lock the quick disassembly rod (note: it must be completed in the folded state).
Handlebar installation
into the clamping slot of the folding handle.
2.2 Raise the riser to lock the folding handle and then fasten the protective sleeve
3. The red light means the battery is charging, and the green light means thebattery
is fully charged (wait for 30 minutes after the green light of the charger is displayed
before unplugging it).Charging time depends on the battery capacity, the general
charging time is 4-6 hours.
4.
W
ar
n
i
n
g
:
Do not charge for more than 10 hours. Keep away from high temperature
environment and store in a cool place.
6 . Installation instructions
1.
2. :
2.1 2.1 2.1 2.2 2.2
3.
Headlight& fenders installation:
3.1 Loosen the headlight screw from the front fork;Install the headlight into the
screw hole of the front fork and tighten the screw with the hexagon tool.
-4-
wrapping rope with tools.
Open the carton of the electric bicycle, take out the electric bicycle, and cut off the
-
5
-
rod and the front wheel protection cover.
4.2 Make sure the front and rear wheels are in line before mounting.First pull the
wheel up, place the disc brake disc into the front brake clamp, then use the No. 15
wrench to tighten the front flower drum fixing screw.
4.3 Adjust the adjusting screw of the disc brake so that the disc brake can rotate
without obvious friction
5.
P
e
dal
i
ns
tall
ation
：
5.1 Check the two pedal. The pedal with "L" printed on the end of the core shaft
should be installed on the left side of the vehicle (without toothed disc) and rotate
counterclockwise. The pedal with "R" is installed on the right side (with tootheddisc)
and rotate clockwise, then use the No.15 wrench
Tighten the foot core shaft (pay attention to screw the foot up by hand and then lock
it with a wrench).
4
.
F
ront wh
ee
l
i
ns
ta
ll
ation
：
4.1 Cut the wrapping rope, remove the front wheel, remove the front fork protection
-4-
rear reflector lamp on the seat rod.
6.2 Insert the seat rod into the frame.
6.3 Adjust the seat position to the height most suitable for your riding position, and
lock the quick release (please make sure the quick release lock is tight).
8.1 First open the folding handle safety buckle.
5.1
6.
Saddle installation
6.1. Open the package, take out the seat cushion and seat rod, and then install the
6.3
7.
Adjust angle of brake lever, meter, gear shifter and louder controller
on handle bar, then tighten them withtools.
8.
Remove the battery
8.2 Then open the folding device.
8.3 Folding the frame, turn the key which on the battery clockwise turn 3 times after
-6-
-
7
-
to the reach on the top).
9.1 First remove the preinstalled cover on the handlebars, If it is difficult to remove,
cut it off with a knife and replace the short handle sleeve as shown, picture.1
9.2 Take out the accelerator from the small box, firstly put the accelerator into the
right side of the handlebar, and then put it into the sheath, and then set the short
handle sleeve, and knock the sleeve into place with the rubber hammer; Picture 2, 3
and 4.
9.3 Find the oil line inside the wire harness and plug it into the throttle Picture 6
the key is pulled off the battery can be removed (when to the third time ,the key need
8.1 8.2 8.3
9.
Accelerator installation instructions
Indice
Lingue:
Altri manuali KAISDA Scooter
