Kangaroo 224 Manuale
Kangaroo®224 Feeding Pump
NORMAL OPERATION
Plug the pump into AC wall outlet.
BATTERY OPERATION
Unplugging the pump from the AC line will automatically put the pump on battery
powere. to recharge the battery, plug the pump into an AC wall outlet. Pump will
automatically begin charging.
These general instructions are for inserting the Kendall Healthcare Pump
Administration Sets into the Kangaroo 224 Feeding Pump.
1. Fill the feeding bag prior to setting up pump.
2. Close roller clamp on pump set.
3. Press “ON”
4. Wait while pump performs systems check.
5. When display reads 0, set rate by turning knob on side of pump.
6. Insert drip chamber into drip chamber guides.
7. Open roller clamp, fill entire line with fluid, close roller clamp.
8. Attach distal connector to feeding tube.
9. Grasp the silicone portion of tubing and gently stretch around the pumps rotor.
Insert the pump set retainer disc into retainer lock on the pump. Thread tubing
through tubing guide.
10. Open roller clamp, press “START/HOLD”. While pump is running, dots will
flash across display.
TO CHANGE RATE:
1. Press “START/HOLD”.
2. Set new rate by rotating knob on side of pump.
3. Press “START/HOLD”.
Directions For Use
Kangaroo®224 Feeding Pump
Listed below are some of the probable cause of alarm conditions and their corrections.
Symptom Probable Cause Corrections
Flow Error
Alarm
(FLO Err)
Feeding container is empty.
Feeding tube or feeding set
tubing is occluded.
Drip chamber is improperly
placed in pump.
Drip chamber walls are coated
with feeding formula.
Sensors in upper drip chamber
guide are blocked.
Refill feeding container. If bag has been in use for
24 hours, replace.
Locate point of occlusion and correct. Note:
occlusion may occur upstream or downstream from
pump.
Check to make sure roller clamp on feeding set
tubing is open.
Check to patency of the feeding tube.
Check to make sure drip chamber is properly
“locked” in position in drip chamber guide.
Check to make sure formula is not preventing
detectors from proper operation. If formula cannot
be removed from inside walls of chamber via
chamber manipulation, replace set.
Check to make sure detectors are free of dried
formula. Remove any deposits by using a cotton
swab dampened with warm soapy water.
Low Battery
Alarm (Lo
BAT)
Battery has been run down
below point of maintaining
accuracy of pump.
Plug pump power cord into wall outlet.
Hold Error
Alarm (Hld
Err)
Pump set has been left in the
hold mode for over 2 ½ minutes.
Press “START/HOLD” to silence alarm, then press
“START/HOLD” again to restart pump.
No Set (no
SEt)
Pump set has been improperly
placed onto pump.
Check to make sure only Kangaroo Pump Set has
been placed onto the pump.
Check to make sure that retainer clip on pump set has
been properly positioned into retainer lock on pump.
System Error
Alarm (SYS
Err)
Rotor is not turning while pump
is running.
Rotor is turning but is not
detected by rotor sensors.
Return pump for technical service.
Return pump for technical service.
No Audible
Alarm
Battery is fully discharged.
Alarm circuitry failure.
Charge battery for a minimum of 15 hours.
Return pump for technical service.
Troubleshooting Guide
Altri manuali Kangaroo Pompa dell'acqua
Manuali Pompa dell'acqua popolari di altre marche
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi
DUROMAX
DUROMAX XP WX Series Manuale utente
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuale utente
Franklin Electric
Franklin Electric IPS Manuale utente
Xylem
Xylem e-1532 Series Manuale utente
Milton Roy
Milton Roy PRIMEROYAL Manuale utente