KEDDY K800 Series Manuale utente
K800
Installation instructions
CONTENTS
GENERAL INFORMATION..................................................................................................3
IMPORTANT POINTS..........................................................................................................3
PREREQUISITES................................................................................................................4
Floor plate
Outdoor air supply
Flue
PREPARATIONS................................................................................................................5-8
Flue connections for rear and top installation
Floor plate and outdoor air connection
INSTALLATION INSTRUCTIONS.....................................................................................9-11
CARE & FIRING INSTRUCTIONS .................................................................................12-14
TECHNICAL SPECIFICATION...........................................................................................15
CERTIFICATES..................................................................................................................16
- 2 -
GENERAL INFORMATION
* Turned hot plate (for rear installation)
* Outdoor air unit
* Glasshatch (816-36)
Important! Keep these installation instructions and the associated firing instructions!
Manufacturer's declaration
IMPORTANT POINTS
* NOTE! Read through all of the installation instructions before beginning the installation.
12-14.
touched.
-
se.
- 3 -
PREREQUISITES
BUILDING NOTICE
DISTANCE TO FLAMMABLE STRUCTURAL
UNITS
in the desired place.
-
-
LOAD-BEARING SURFACE
FLOOR PLATE
-
steel plate.
OUTDOOR AIR SUPPLY
-
-
-
FLUE
2
-
CHIMNEY CONNECTIONS
The illustration on page 5 shows the K800 from
- 4 -
Min 630
PREPARATIONS
1. FLOOR PLATE AND OUTDOOR AIR CONNEC-
TION
accessory.
2. FLUE CONNECTION
Note! If you install Keddy's floor glass, the di-
mensions above must be extended by 6 mm, i.e.
they become 926/1012 and 1066/1151 mm.
this at the end of the Installation instructions on p. 11.
-
- 5 -
Min 630 mm
195 mm
Min 595 mm
214 mm
100 mm
125 mm
100 mm
800 mm
Floor Plate
125 mm
Ø 100 mm
Ø 100 mm
665 mm
955 mm
Min 595 mm
45°
Floor Plate
EXAMPLE A
Rear connection directly into a chimneybreast or
a masonry chimney, e.g. a Heda Chimney.
Mark
-
installed.
-
NOTE! Bricking the pipe into the chimney is
not allowed.
EXAMPLE B
Rear connection through a flammable wall
-
3. UNPACKING / DISMANTLING
The stove can be moved in as delivered
-
- 6 -
-
NOTE! To close the door, push it closed without
lifting the lock hasp.
- 7 -
Keep a hand on the panels during this op-
eration, to prevent them from falling on the floor.
NOTE! Model 816-36 with whole sidepanel
should not be removed as it also holds the glass-
panels in place.
You have now removed all of the necessary parts and
can unscrew the stove and move it into the house.
NOTE! Because the stove is heavy and is also
equipped with adjustment screws under the base, it
can be a good idea to take a piece of the packaging to
stand the stove on, in order to protect the floor while
manoeuvring it into position.
Concrete panel guide
- 8 -
INSTALLATION INSTRUCTIONS
In most cases the installation is identical on all K800 stoves. When it differs we will describe it in the
text. Before starting on the installation of the stove, the following steps need to be fully completed:
The chimney:
Outdoor air supply
Floor plate
Several operations have to be carried out before the stove is put into place.
-
holes in the four corners of the plate. If
the correct position.
-
- 9 -
We are now ready to place the stove in its intended position.
-
NOTE! Because the stove is heavy and is also
equipped with adjustment screws under the base,
it can be a good idea to take a piece of the pack-
aging to stand the stove on, in order to protect
the floor while manoeuvring it into position.
- 10 -
Altri manuali per K800 Series
1
Indice
Altri manuali KEDDY Stufa
