Kemppi MasterTig MLS 3003 ACDC Manuale utente
1
Service manual
Mastertig MLS 3003 ACDC
Version 1.2
2
Technical data
The device may be repaired only by a person legally authorized
perform electric work!
Measured values may differ by the type and model of multimeter used.
Maximum power can be achieved with 20 kVA generator for the power source.
Mains Voltage 3 ~ 230 V - 10% … 460 V +10%, 50/60 Hz
Mains cable H07RN-F 4G2.5, length 5 m
Fuse 20/ 16A delayed fuse
Rated power 40% 100%
TIG 300A TIG 190A
MMA 250A MMA 190A
Minimum Current TIG 3A ( AC 5A ) / MMA 10A
Open circuit Voltage 58 V
Power Factor at nominal values 0,95
Efficiency at nominal values 80-84 % (250A / 30V)
77-81 % (300A / 22V)
Open circuit power TIG < 13W
MMA 190W
Electrode sizes to be welded 1,5 - 5,0 mm
Size ( l x w x h ) 500 x 180 x 390 mm
Weight 25 kg
3
User interface
1.2.
3.
4.
5.
6.
1. Gas connector for TIG torch
2. Welding current connection (negative)
3. Operation panel
4. Remote controller connection
5. TIG -torch control connection
6. Welding current connection (positive)
7. Main switch
8. Gas connector
7
8.
Error code Description
Err 3 Overvoltage
Err 4 Over heating
Err 6 Internal fault, secondary voltage over the limit.
Err 8 Maximum overheat time, machine doesn’t cool down fast enough. Only machine
shutdown and restart removes error.
Err 61 Water connection, water cooled gun connected without cooler.
COO Ler Cooler error:
- Cooling liquid over- / under pressure state
- Overheated alarm
BuS Err Communication between panel and power source isn’t possible
Err rSt System error, machine makes reset itself.
4
Setup functions
Welding current upslope time * A1
ON The upslope time depends on the welding
current
OFF The upslope time is fixed
Welding current downslope time * A2
ON The downslope time depends on the welding
current
OFF The downslope time is fixed
TIG Antifreeze * A3
ON TIG Antirfeeze is ON
OFF TIG Antifreeze is OFF
MMA Antifreeze * A4
ON MMA antifreeze is ON
OFF MMA antifreeze is OFF
VRD ***
(MMA open circuit voltage) A7
ON VRD-function: MMA open circuit voltage < 35
Vdc
OFF Normal open circuit voltage is 50 Vdc
2T-function´s downslope cutoff A8
ON On 2T-function the downslope is cut off by a
quick press on the start switch
OFF Quick press on the start switch has no function
Tacking automatics A9
ON Tacking automatics is ON; no downslope, if the
weld is shorter than 3 s
OFF Tacking automatics is OFF
Current upslope speed A10
ON If upslope time is 0,0 s, it goes to 0,2 s from the
halfway of currents > 100 A.
OFF Maximum current upslope speed
Method selection by remote
controller * A12
ON Method selection; TIG: minimum end of the
range of the remote controller, MMA: the
maximum end of the remote controller range
OFF The remote controller works as a normal current
adjustment
Entering the advanced setup press and hold the setup and Return buttons at the same
time. Changing the level press Setup button shortly
* Setting is always on ** Adjustable also by the Quick Setup *** Requires VRD card
5
Setup functions
Start current level A13
ON Start current level in use
OFF Start current level not in use
Current ”freezing” A14
ON During downslope the current can be ”frozen”
onto a certain level, using the start switch
OFF ”Freeze” function is OFF
TIG -torch auxiliary switches (RTC
20) * A15
ON Torch auxiliary switches are used to select
memory channels
OFF Torch auxiliary switches adjust welding current
TIG -torch auxiliary switches (RTC
20) activation * A16
ON Auxiliary switches are always active
OFF Auxiliary switches are active only when torch
control is selected
Cooling unit flow control * A17 ON Flow control is active
OFF Flow control is not active
Cooling unit control * A19
ON Controlled run
OFF Continous run
Coolant temperature watch * A20
ON Temperature watch is active
OFF Temperature watch is not active
Remote controller automatic
detection * A21
ON Automatic detection is ON
OFF Automatic detection is OFF
End current level A22
ON 4T-LOG: End current level is in use
OFF MINILOG: End current level is not in use
Tungsten electrode type *** A23 NOR Normal = Gray tungsten
GRN GRN = Green tungsten
* Setting is always on ** Adjustable also by the Quick Setup ***Depends on panel software version
6
Setup functions
Contact ignition current * B1
20 Factory setting 20 A
3…2
30
Adjustment range 3…230 A
Spark ignition duration * B2
1.0 Factory setting 1,0 s.
0.2
…2.
0
Adjustment range 0,2…2,0 s.
Downslope cutoff level * B3
10 Factory setting 10 % of the welding current
5…4
0
Adjustment range 5…40 % of the welding
current
Factory settings recall * B5
OFF Factory setting
PAN Recalls factory settings to the panel, but keeps
memory channels
ALL Recalls factory settings and empties the memory
channels
Downslope interruption –upslope
angle * B6
1 Upslope speed maximum
2 According to the upslope setting
3 According to the downslope
Non-linear downslope
(Current drop in the beginning of
downslope)
B7
OFF Factory setting
0…5
0
Adjustment range 0…50 % of welding current
Torch switch long press * B8
0.4 Factory setting 0,4 s.
0.3
…1.
0
Adjustment range 0,3…1,0 s.
Cooling unit post running time * B9 OFF Factory setting 4 min.
ON Post-running time 30 s.
* Setting is always on ** Adjustable also by the Quick Setup
7
Setup functions
Spot welding spot-time * B10
OFF Factory setting 0,0…15,0 s.
ON 0…150 s.
MMA dynamics ** B11
0 Factory setting
-
9…0
…9
Adjustment range -9 = soft arc, 9 = rough arc
MMA ignition pulse ** B12
0 Factory setting
-
9…0
…9
Adjustment range -9 = minimum overrun, 9 =
maximum overrun
Start current level * B13
10 Factory setting 10 % of the welding current
OFF Minimum current
5…4
0
Adjustment range 5…40 % of the welding
current
Display recovery time B14
5.0 Factory setting 5,0 s.
1.0
…20
,0
Adjustment range 1,0…20,0 s.
2T Hot Start duration ** B15
1.0 Factory setting 1,0 s.
0.1
…5.
0
Adjustment range 0,1…5,0 s.
* Setting is always on ** Adjustable also by the Quick Setup
8
Setup functions
Pregas time minimum * C1
0.0 Factory setting 0,0 s.
0.0
…2.
0
Adjustment range 0,0…2,0 s.
Postgas time minimum * C7
1.0 Factory setting 1,0 s.
0…1
0
Adjustment range 0…10 s.
AC balance minimum * C16
-80 Factory setting -80 %
-
80…
-10
Adjustment range -80…-10 %
Pregas time maximum * D1
1 Factory setting 1 s.
0…1
0
Adjustment range 0…10 s.
Postgas time maximum * D7
30 Factory setting 30 s.
15…
150
Adjustment range 15…150 s.
AC balance maximum * D16
10 Factory setting 10 %
0…2
0
Adjustment range 0…120 %
* Setting is always on ** Adjustable also by the Quick Setup
9
Setup functions
AC frequency ** E1
60 Factory setting 60 Hz
50…250 Adjustment range 50…250 Hz
AC waveform ** E2
Sqr Square wave
Sin Sinus wave
Half cycle AC E3
5 Factory setting 5 A
5…20 Adjustment range 5…20 A
AC balance ** E4
-25 Factory setting -25 %
-50…10 Adjustment range -50…10 %
Negative ignition current * E5
100 Factory setting 100 %
100…500 Adjustment range 100…500 % (Limited by
the max. of the power source)
Positive ignition current * E6
50 Factory setting 50 %
30…150 Adjustment range 30…150 % (Limited by the
max. of the power source)
Positive ignition sequence time * E7
10 Factory setting 10 = 0,01 s
0…20 Adjustment range 0…20 = 0,0…0,02 s
Ignition cycle total time */*** E8
0.20 Setting 0,20 s.
0.01…1,0 Adjustment range 0,01…1,0 s.
MIX TIG cycle time ** E9
0.6 Factory setting
0.1…1,0 Adjustment range 0,1…1,0 s.
* Setting is always on ** Adjustable also by the Quick Setup *** Note panel software version
10
Setup functions
MIX TIG AC pulse ratio ** E10
50 Factory setting 50 %
10…
90
Adjustment range 10…90 %
MIX TIG DC level ** E11
100 Factory setting 100 %
50…
150
Adjustment range 50…150 %
Spotwelding time * E12
10 Factory setting 10 ms.
1…2
00
Adjustment range 1…200 ms.
* Setting is always on ** Adjustable also by the Quick Setup
Altri manuali per MasterTig MLS 3003 ACDC
1
Indice
Altri manuali Kemppi Sistema di saldatura
Kemppi
Kemppi KEMPACT 251R Manuale utente
Kemppi
Kemppi FastMig MF 29 Manuale utente
Kemppi
Kemppi MinarcMig 180 Manuale utente
Kemppi
Kemppi KEMPOMAT 320 KEMPOMAT 320C Manuale utente
Kemppi
Kemppi WELDFORCE KPS 3500 Manuale utente
Kemppi
Kemppi Promig 530 Manuale utente
Kemppi
Kemppi X8 MIG Manuale utente
Kemppi
Kemppi AX MIG Welder Manuale utente
Kemppi
Kemppi ArcValidator Manuale utente
Kemppi
Kemppi FastMig MF 29 Manuale utente
Kemppi
Kemppi Flexlite GX Series Manuale utente
Kemppi
Kemppi M 420MV FastMig Manuale utente
Kemppi
Kemppi FastMig Pulse 350 Manuale utente
Kemppi
Kemppi FastMig X 450 Manuale utente
Kemppi
Kemppi Kempact Pulse 3000 Manuale utente
Kemppi
Kemppi Protig 410 Manuale utente
Kemppi
Kemppi FASTMIG MS 200 Manuale utente
Kemppi
Kemppi Master S 400 Manuale utente
Kemppi
Kemppi FastMig KM500 Manuale utente
Kemppi
Kemppi Pro Evolution 3200 Manuale tecnico
