Ken A Vision Vision Viewer 7890B Manuale utente

Vision Viewer

Instruction Manual

7890B

7890P

7890UM

Thank you for your purchase of a Ken-A-Vision Vision Viewer™! You have

acquired an easy to use, reliable solution for any presentation need, be it

classroom or conference room. Images captured by your camera will be

transmitted directly to your TV/Monitor, Projector, or VCR (7890B or 7890P) or

through your computer to a Projector, DVR, Flash drive or other digital device

(7890UM).

7890B includes: 7890P includes: 7890UM includes:

Formatted for NTSC Formatted for PAL Attached USB Cable

Appropriate Power

Supply

Appropriate Power

Supply

Video/Power Cable

Attached

Video/Power Cable

Attached

28mm Microscope

Adapter

28mm Microscope

Adapter

28mm Microscope

Adapter

Applied VisionTM

Software

Applied VisionTM

Manual

Connecting the Vision Viewer™ to Output Device

7890B and 7890P (Analog/Video Device)

Connecting the Video/Power Cable

Your Video/Power cables are pre-attached to the Vision Viewer™ camera.

Simply connect the video composite (RCA type) cable (yellow connector) into

the "video-in" on your TV/Monitor, VCR or Projector (output device). Then

connect the power supply to the power cable (black connector). Next connect

the other end of your power supply to a 110 volt (or 220 volt) electrical outlet.

Now push the "ON" switch to activate the camera. Video image from camera

should appear on your output device.

Note: If no "Video-in" is available, you may need an RF Modulator or a VCR

recorder.

7890UM (Digital Video Device)

Prior to connecting the USB cable, you must first install the supplied software.

Please see the Applied Vision Software booklet provided with the enclosed

software CD.

Once the software is loaded onto your computer, connect the USB cable to the

computer. Click on the desktop icon for the software, follow simple

instructions and the camera should show an image on your computer screen.

See Applied Vision Software Manual if there are any problems with an image.

You are ready to go!

Output from computer to Projector, VCR, DVR, Flash drive, CD's and/or DVD

will, most commonly, use VGA (15 pin) cables, but there are other possibilities

dependent upon your computer set up. See the owner's manual of the

computer for the operating procedures.

Note: The USB provides ample power to the camera, no separate power

supply needed

Focusing:

The focusing ring located on the camera head is a rubber knurled focusing

system with 6mm lens. Simply turn the focusing ring until you have obtained a

crisp clear image.

NOTE: The lens is permanently attached and may NOT be removed. Use care

when reaching the optimal focal distance, do not use force, and avoid turning

the focus ring to extremes in either direction.

Connecting the microscope eyepiece adapter:

The Vision Viewer™ as shipped came with a 28mm microscope eyepiece

adapter that allows your Vision Viewer™ to be coupled with microscopes or

other objects which have eyepieces. The 28mm adapter included will fit most

compound microscopes, but not stereo (dissecting) microscopes unless they

have an unusually small outer diameter..

NOTE: Before installing the microscope eyepiece adapter, measure the size of

the outside diameter of the microscope eyepiece to be sure adapter will fit over

the end of the eyepiece. Remove the rubber eyecup if present.

1. Place the microscope eyepiece adapter over one (if Dual-Headed or

Binocular) of the microscope's eyepieces. If there is a rubber eyecup on

the microscope eyepiece, it should be removed first. If there are two

eyepieces on your microscope, light entering the open eyepiece will not

cause any problems with imaging.

2. Attach the Vision Viewer™ to the eyepiece adapter by gently sliding the

Vision Viewer™ camera head onto the eyepiece adapter, aligning the

narrow part of the microscope adapter with the inside opening of the

Vision Viewer™ camera (inside the knurled focusing ring).

Note: Use only genuine Vision Viewer™ parts and accessories. All

Ken-A-Vision parts provided are made specifically for the Vision Viewer™

and failure due to use of non-vision viewer parts will void the warranty!

Lighting:

Your Vision Viewer™ operates using ambient, room light. If using the camera

in a severely darkened room, supplement the light entering the camera by

using a penlight, flashlight or small lamp near the camera, so that there is

more local input light for the camera to work with.

Never point your Vision Viewer™ at direct sunlight. Subjecting the Camera

"eye" to direct sunlight will discolor the filter over the CMOS chip causing

abnormal colors and or permanent focusing problems. It may even destroy

the camera's ability to capture an image.

Camera complies with Class A and B, part 15 of the FCC Rules.

Use only Ken-A-Vision Video Flex parts. The Power Supply and Charger are

made exclusively for the Video Flex. Failure to use non-Video Flex parts will

void your warranty.

INFORMATION TO THE USER Changes or modifications not expressly

approved by the party responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy, and if not installed and used in accordance with instructions,

may cause harmful interference to radio communication. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio reception which can be

determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures: Reorient

or relocate the receiving antenna and/or increase the separation distance

between the equipment and the receiver, and/or connect equipment into an

outlet on a circuit different from that which the receiver is connected; and/or

consult your dealer or experienced radio/ TV technician for help.

5615 Raytown Road • Kansas City, MO 64133 U.S.A.

Tel.: 816-353-4787 • Fax: 816-358-5072

email:info@ken-a-vision.com • www.ken-a-vision.com

INS-VV

Ken-A-Vision reserves the right to make design improvements and other changes in accordance with the

latest technology. There is no obligation to make changes in products already manufactured. Patents

Altri manuali per Vision Viewer 7890B

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ken A Vision Telecamera per documenti

Ken A Vision

Ken A Vision Video Flex 7200HD Manuale utente

Ken A Vision

Ken A Vision FlexCam 2 910-171-200 Manuale utente

Ken A Vision

Ken A Vision Video Flex 7200HD Manuale utente

Ken A Vision

Ken A Vision FlexCam 2 910-171-200 Manuale utente

Ken A Vision

Ken A Vision StudentCam 910-171-120 Manuale utente

Ken A Vision

Ken A Vision Vision Viewer 7890B Manuale utente

Ken A Vision

Ken A Vision TeachCam 910-171-150 Manuale utente

Ken A Vision

Ken A Vision 7880OR Manuale utente

Ken A Vision

Ken A Vision FlexCam iCam 910-171-102 Manuale utente

Ken A Vision

Ken A Vision FlexCam 910-171-210 Manuale utente

Ken A Vision

Ken A Vision Doc Cam Guida all'installazione

Ken A Vision

Ken A Vision Video Flex 7610 Manuale utente

Ken A Vision

Ken A Vision Vision Viewer 7890UM Manuale utente

Ken A Vision

Ken A Vision Video Flex 7600 Manuale utente

Ken A Vision

Ken A Vision FlexCam 910-171-210 Manuale utente

Ken A Vision

Ken A Vision Vision Viewer 7880YL Manuale utente

Ken A Vision

Ken A Vision StudentCam 910-171-120 Manuale utente

Ken A Vision

Ken A Vision 7610 Manuale utente

Ken A Vision

Ken A Vision Video Flex 7100 Manuale utente

Ken A Vision

Ken A Vision Video Flex 7100 Manuale utente

Ken A Vision

Ken A Vision Video Flex 7200UM Manuale utente

Ken A Vision

Ken A Vision Video Flex 7600 Manuale utente

Ken A Vision

Ken A Vision IDCam 910-171-125 Manuale utente

Ken A Vision

Ken A Vision Video Flex 7100 Manuale utente

Manuali Telecamera per documenti popolari di altre marche

AVer

AVer AVerVision F35 Manuale utente

Lumens

Lumens PS760 Manuale utente

Genee World

Genee World GV8100 Manuale utente

Touchboards

Touchboards Vidifox DV 480 Manuale utente

Dukane

Dukane 210 Manuale utente

TTS

TTS Easi-View Pro Manuale utente

Lumens

Lumens dc153 Manuale utente

Avermedia

Avermedia AVerVision SPB350 Manuale utente

AVer

AVer TR311V2 Manuale utente

Inswan

Inswan INS-3 Manuale utente

Genee

Genee Vision 6100 Manuale utente

Rolls

Rolls DB14 - 02/10 Manuale utente

Lumens

Lumens DC-W80 Manuale utente

AVer

AVer AVerVision SPB350+ Manuale utente

Dukane

Dukane FASTFAX AV-P750U Manuale utente

Optoma

Optoma DC554 Manuale utente

Ipevo

Ipevo Ziggi Manuale utente

Vidifox

Vidifox PV 380 Manuale utente