Keyline NINJA LASER Manuale utente
COMPLETE PRODUCT REGISTRATION FORM
Complete enclosed form and fax to 216-803-0202 or e-mail to info@keyline-
usa.com. This information is required to activate your warranty and inform you
of software updates and new products.
* IMPORTANT *
REGISTERING YOUR MACHINE
Thank you for your purchase of the Keyline Ninja Laser.
Before continuing with machine setup and use, please complete the following;
1
2
INSTALLING SAFETY SHIELD
STEP 1:
Remove the Ninja Laser
and the shield from the box
Locate the 4mm allen
wrench in the tool kit
Your Ninja Laser safety shield is shipped separate from the machine in order to
protect the shield in transit. Please follow the instructions for installing the shield
upon receipt before initial use.
STEP 2:
Remove the screws on each side
of the Ninja Laser and set aside
STEP 3:
Line up shield on machine so
opening is directly over screw hole.
Slots must be perpendicular to base.
STEP 4:
Reinsert screws and tighten down with
4mm allen wrench on both sides.
Machine is now ready for use.
Powering Machine OFF
Cable Connection & Powe ing Machine ON
1. Attach the 9-pin connector cable to the port on the LEFT SIDE of the console AND to
the back of the machine. SECURE WITH ATTACHED SCREWS. Also, connect the
black cable to the console and the back of the machine.
2. Attach power cord to back of machine and plug into a properly grounded outlet.
3. Make sure the ON/OFF button is pressed down and illuminated to RED.
4. Rotate the Emergency Stop button towards the back of the machine until it releases
outward. The machine will now begin to start-up. This process can take up to 4
minutes. Proceed with LOGIN (page 4).
POWERING MACHINE ON/OFF
*MOBILE USERS: YOU MUST USE A PURE SINE WAVE INVERTER WITH
1100 WATTS (or greater) TO POWER THE MACHINE OR MACHINE
MOTOR WILL NOT WORK PROPERLY
3
At MAIN MENU, select Power button Select YES to log out, then select
Power button again at Login screen
Select YES to exit
4
Select ADMINSTRATOR
LOGIN / PASSWORD ENTRY
TIP: Use included stylus with touch screen to ensure accurate selections
From Main Menu, Select SETUP, then USERS and then CHANGE PASSWORD.
At the Change Password screen enter in your new password and confirm
(leave Old Password line blank) then select NEXT. Administrator password is
now set.
PASSWORD CREATION (OPTIONAL) -Skip this section if you do not want a password-
Leave password screen blank, no
default password is set, Select NEXT.
To create password, see below.
IMPORTANT
MACHINE CALIBRATIONS
DO NOT CALIBRATE THE JAWS. The Ninja Laser is manufactured to highly precise
specifications. Machines and consoles are uniquely paired on initial factory setup. All cutter
and jaw calibrations have been performed at the factory matching the jaw to the machine
thus making calibrations by the user unnecessary. Consoles and machines cannot be
swapped with different versions without consenting Keyline technical team for instructions.
SAFETY SHIELD
The safety shield works in conjunction with the software prompts. If the shield is left open,
the software will prompt to close the shield after each selection and may reset to the
beginning of the procedure. Make sure to complete all parts of the process (i.e. positioning
AC jaw in correct position, securing key on jaw, removing tip stop, etc) at one time, then
close the shield before proceeding to next step. This will avoid having to replicate steps.
KEY MATERIAL
The Ninja Laser defaults to cutting brass keys as the key material type. If you are cutting a
different type of metal key, such as steel, nickel silver or aluminum, you can make the
selection in the cutting screen. Please note the Ninja Laser cannot cut or decode any type
of plastic key.
USE OF AFTERMARKET SPARE PARTS
Keyline machines require the use of factory original parts. Aftermarket cutters, tracers and
adaptors are not recommended and may cause product damage that will void your machine
warranty.
MACHINE PACKAGING
Please retain all machine packaging for transportation purposes. Packaging is specially
designed to safely transport the machine and it’s components. Keyline is not responsible for
providing additional packing material if original boxes are lost, damaged or discarded.
FOLLOW SCREEN PROMPTS
Please thoroughly follow the screen prompts and don’t jump ahead
MAINTENANCE
Please keep the machine and work area free of chips and as clean as possible for safety
and the best use .
5
To change the material type, simply touch the
BRASS icon on the screen until you reach the
desired material; BRASS, STEEL, NiSi (Nickel
Silver) or ALU (aluminum)
CUT BY DECODE – HIGH SECURITY
Select : Cut by Code
when prompted
6
1. Select: SETUP
Select MODEL, then NEXT
Select MAKE, then NEXT
Select CARS
Select DECODE, then select NEXT Take note of tip stop location.
The red bar indicates position (0 is
farthest slot back, then 1, then 2
Select YEAR RANGE, then NEXT
NOTE: Make sure AC Jaw is in DECODE
position on jaw carriage as shown in the
picture to the right. Confirm original key
is clean and free of dirt, chips, etc.
TIP: DO NOT DECODE PLASTIC
KEYS! Only metal keys can be decoded
and cut on the Ninja Laser.
CUT BY DECODE – H.S., cont. 7
Confirm tip stop tool removal Decoding in process
Confirm jaw position, select OK
Decode complete; Select OK Depths and key code displayed
Select NEXT, then proceed with
cutting the key by code (refer to
Page 8 – CUT BY CODE-H.S.,
cont. to proceed with cutting
Insert key correctly on jaw, remove tip
stop and close shield, select NEXT
CUT BY CODE – HIGH SECURITY
Select : Cut by Code
when prompted
8
1. Select: SETUP
Select MODEL, then NEXT
Select MAKE, then NEXT
Select CARS
Select CODES, then select NEXT Enter code, (ex. K041), select NEXT
NOTE: Make sure AC Jaw is in cutting
position on the jaw carriage as shown in
the picture to the right.
TIP: Cutting a test key is also
recommended on first use to verify correct
key cutting procedure.
Select YEAR RANGE, then NEXT
CUT BY CODE – HIGH SECURITY, cont. 9
Insert key correctly on jaw, paying
close attention to tip stop position
(shown in RED). Tighten down key,
then remove tip stop. Close shield.
When key is ready, select CUT
Key depths appear, select NEXT
Confirm jaw placement, select OK
Confirm tip stop removal tip stop,
select OK
Make sure jaw is in cutting position
Key cutting begins
Altri manuali per NINJA LASER
2
Indice
Altri manuali Keyline Taglierina
